Xilinx DS312 Spartan-3E FPGA Family Data Sheet, Data Sheet

Loading...
1

Spartan-3E FPGA Family Data Sheet

DS312 July 19, 2013

Product Specification

Module 1: Introduction and Ordering Information

Module 3: DC and Switching Characteristics

DS312 (v4.1) July 19, 2013

DS312 (v4.1) July 19, 2013



Introduction





Features



Absolute Maximum Ratings



Architectural Overview



Supply Voltage Specifications



Package Marking



Recommended Operating Conditions



Ordering Information



DC Characteristics

Module 2: Functional Description



DC Electrical Characteristics

Switching Characteristics •

I/O Timing

DS312 (v4.1) July 19, 2013



SLICE Timing



Input/Output Blocks (IOBs)



DCM Timing



Overview



Block RAM Timing



SelectIO™ Signal Standards



Multiplier Timing



Configuration and JTAG Timing



Configurable Logic Block (CLB)



Block RAM



Dedicated Multipliers

Module 4: Pinout Descriptions



Digital Clock Manager (DCM)

DS312 (v4.1) July 19, 2013



Clock Network



Pin Descriptions



Configuration



Package Overview



Powering Spartan®-3E FPGAs



Pinout Tables



Production Stepping



Footprint Diagrams

© Copyright 2005–2013 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Spartan, ISE, Artix, Kintex, Zynq, Vivado, and other designated brands included herein are trademarks of Xilinx in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.

DS312 July 19, 2013 Product Specification

www.xilinx.com 1

8

Spartan-3E FPGA Family: Introduction and Ordering Information

DS312 (v4.1) July 19, 2013

Product Specification

Introduction The Spartan®-3E family of Field-Programmable Gate Arrays (FPGAs) is specifically designed to meet the needs of high volume, cost-sensitive consumer electronic applications. The five-member family offers densities ranging from 100,000 to 1.6 million system gates, as shown in Table 1. The Spartan-3E family builds on the success of the earlier Spartan-3 family by increasing the amount of logic per I/O, significantly reducing the cost per logic cell. New features improve system performance and reduce the cost of configuration. These Spartan-3E FPGA enhancements, combined with advanced 90 nm process technology, deliver more functionality and bandwidth per dollar than was previously possible, setting new standards in the programmable logic industry. Because of their exceptionally low cost, Spartan-3E FPGAs are ideally suited to a wide range of consumer electronics applications, including broadband access, home networking, display/projection, and digital television equipment. The Spartan-3E family is a superior alternative to mask programmed ASICs. FPGAs avoid the high initial cost, the lengthy development cycles, and the inherent inflexibility of conventional ASICs. Also, FPGA programmability permits design upgrades in the field with no hardware replacement necessary, an impossibility with ASICs.

• •







• •

• • •

Features •



Very low cost, high-performance logic solution for high-volume, consumer-oriented applications Proven advanced 90-nanometer process technology Multi-voltage, multi-standard SelectIO™ interface pins • Up to 376 I/O pins or 156 differential signal pairs

• • • •

LVCMOS, LVTTL, HSTL, and SSTL single-ended signal standards • 3.3V, 2.5V, 1.8V, 1.5V, and 1.2V signaling • 622+ Mb/s data transfer rate per I/O • True LVDS, RSDS, mini-LVDS, differential HSTL/SSTL differential I/O • Enhanced Double Data Rate (DDR) support • DDR SDRAM support up to 333 Mb/s Abundant, flexible logic resources • Densities up to 33,192 logic cells, including optional shift register or distributed RAM support • Efficient wide multiplexers, wide logic • Fast look-ahead carry logic • Enhanced 18 x 18 multipliers with optional pipeline • IEEE 1149.1/1532 JTAG programming/debug port Hierarchical SelectRAM™ memory architecture • Up to 648 Kbits of fast block RAM • Up to 231 Kbits of efficient distributed RAM Up to eight Digital Clock Managers (DCMs) • Clock skew elimination (delay locked loop) • Frequency synthesis, multiplication, division • High-resolution phase shifting • Wide frequency range (5 MHz to over 300 MHz) Eight global clocks plus eight additional clocks per each half of device, plus abundant low-skew routing Configuration interface to industry-standard PROMs • Low-cost, space-saving SPI serial Flash PROM • x8 or x8/x16 parallel NOR Flash PROM • Low-cost Xilinx® Platform Flash with JTAG Complete Xilinx ISE® and WebPACK™ software MicroBlaze™ and PicoBlaze embedded processor cores Fully compliant 32-/64-bit 33 MHz PCI support (66 MHz in some devices) Low-cost QFP and BGA packaging options Common footprints support easy density migration Pb-free packaging options XA Automotive version available

Table 1: Summary of Spartan-3E FPGA Attributes Device

System Equivalent Gates Logic Cells

CLB Array (One CLB = Four Slices) Total Total Rows Columns CLBs Slices 22 16 240 960 34 26 612 2,448 46 34 1,164 4,656 60 46 2,168 8,672 76 58 3,688 14,752

XC3S100E 100K 2,160 XC3S250E 250K 5,508 XC3S500E 500K 10,476 XC3S1200E 1200K 19,512 XC3S1600E 1600K 33,192 Notes: 1. By convention, one Kb is equivalent to 1,024 bits.

Distributed RAM bits(1) 15K 38K 73K 136K 231K

Block Dedicated RAM Multipliers bits(1) 72K 216K 360K 504K 648K

4 12 20 28 36

DCMs

Maximum User I/O

Maximum Differential I/O Pairs

2 4 4 8 8

108 172 232 304 376

40 68 92 124 156

© Copyright 2005–2013 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Spartan, ISE, Artix, Kintex, Zynq, Vivado, and other designated brands included herein are trademarks of Xilinx in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 2

Spartan-3E FPGA Family: Introduction and Ordering Information

Architectural Overview •

The Spartan-3E family architecture consists of five fundamental programmable functional elements: •

Configurable Logic Blocks (CLBs) contain flexible Look-Up Tables (LUTs) that implement logic plus storage elements used as flip-flops or latches. CLBs perform a wide variety of logical functions as well as store data.



Input/Output Blocks (IOBs) control the flow of data between the I/O pins and the internal logic of the device. Each IOB supports bidirectional data flow plus 3-state operation. Supports a variety of signal standards, including four high-performance differential standards. Double Data-Rate (DDR) registers are included.



Block RAM provides data storage in the form of 18-Kbit dual-port blocks.



Multiplier Blocks accept two 18-bit binary numbers as inputs and calculate the product.

Digital Clock Manager (DCM) Blocks provide self-calibrating, fully digital solutions for distributing, delaying, multiplying, dividing, and phase-shifting clock signals.

These elements are organized as shown in Figure 1. A ring of IOBs surrounds a regular array of CLBs. Each device has two columns of block RAM except for the XC3S100E, which has one column. Each RAM column consists of several 18-Kbit RAM blocks. Each block RAM is associated with a dedicated multiplier. The DCMs are positioned in the center with two at the top and two at the bottom of the device. The XC3S100E has only one DCM at the top and bottom, while the XC3S1200E and XC3S1600E add two DCMs in the middle of the left and right sides. The Spartan-3E family features a rich network of traces that interconnect all five functional elements, transmitting signals among them. Each functional element has an associated switch matrix that permits multiple connections to the routing.

X-Ref Target - Figure 1

Figure 1: Spartan-3E Family Architecture

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 3

Spartan-3E FPGA Family: Introduction and Ordering Information

Configuration

I/O Capabilities

Spartan-3E FPGAs are programmed by loading configuration data into robust, reprogrammable, static CMOS configuration latches (CCLs) that collectively control all functional elements and routing resources. The FPGA’s configuration data is stored externally in a PROM or some other non-volatile medium, either on or off the board. After applying power, the configuration data is written to the FPGA using any of seven different modes:

The Spartan-3E FPGA SelectIO interface supports many popular single-ended and differential standards. Table 2 shows the number of user I/Os as well as the number of differential I/O pairs available for each device/package combination.



Master Serial from a Xilinx Platform Flash PROM



Serial Peripheral Interface (SPI) from an industry-standard SPI serial Flash



Byte Peripheral Interface (BPI) Up or Down from an industry-standard x8 or x8/x16 parallel NOR Flash



Slave Serial, typically downloaded from a processor



Slave Parallel, typically downloaded from a processor



Boundary Scan (JTAG), typically downloaded from a processor or system tester.

Spartan-3E FPGAs support the following single-ended standards: •

3.3V low-voltage TTL (LVTTL)



Low-voltage CMOS (LVCMOS) at 3.3V, 2.5V, 1.8V, 1.5V, or 1.2V



3V PCI at 33 MHz, and in some devices, 66 MHz



HSTL I and III at 1.8V, commonly used in memory applications



SSTL I at 1.8V and 2.5V, commonly used for memory applications

Spartan-3E FPGAs support the following differential standards:

Furthermore, Spartan-3E FPGAs support MultiBoot configuration, allowing two or more FPGA configuration bitstreams to be stored in a single parallel NOR Flash. The FPGA application controls which configuration to load next and when to load it.



LVDS



Bus LVDS



mini-LVDS



RSDS



Differential HSTL (1.8V, Types I and III)



Differential SSTL (2.5V and 1.8V, Type I)



2.5V LVPECL inputs

Table 2: Available User I/Os and Differential (Diff) I/O Pairs Package

VQ100 VQG100

CP132 CPG132

TQ144 TQG144

PQ208 PQG208

FT256 FTG256

FG320 FGG320

FG400 FGG400

FG484 FGG484

Footprint Size (mm)

16 x 16

8x8

22 x 22

30.5 x 30.5

17 x 17

19 x 19

21 x 21

23 x 23

Device

User

Diff

User

Diff

User

Diff

User

Diff

User

Diff

User

Diff

User

Diff

User

Diff

XC3S100E

66(2) 9(7)

30 (2)

83 (11)

35 (2)

108 (28)

40 (4)

-

-

-

-

-

-

-

-

-

-

XC3S250E

66 (7)

30 (2)

92 (7)

41 (2)

108 (28)

40 (4)

158 (32)

65 (5)

172 (40)

68 (8)

-

-

-

-

-

-

XC3S500E

66(3) (7)

30 (2)

92 (7)

41 (2)

-

-

158 (32)

65 (5)

190 (41)

77 (8)

232 (56)

92 (12)

-

-

-

-

XC3S1200E

-

-

-

-

-

-

-

-

190 (40)

77 (8)

250 (56)

99 (12)

304 (72)

124 (20)

-

-

XC3S1600E

-

-

-

-

-

-

-

-

-

-

250 (56)

99 (12)

304 (72)

124 (20)

376 (82)

156 (21)

Notes: 1. 2. 3.

All Spartan-3E devices provided in the same package are pin-compatible as further described in Module 4, Pinout Descriptions. The number shown in bold indicates the maximum number of I/O and input-only pins. The number shown in (italics) indicates the number of input-only pins. The XC3S500E is available in the VQG100 Pb-free package and not the standard VQ100. The VQG100 and VQ100 pin-outs are identical and general references to the VQ100 will apply to the XC3S500E.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 4

Spartan-3E FPGA Family: Introduction and Ordering Information

Package Marking On the QFP and BGA packages, the optional numerical Stepping Code follows the Lot Code.

Figure 2 provides a top marking example for Spartan-3E FPGAs in the quad-flat packages. Figure 3 shows the top marking for Spartan-3E FPGAs in BGA packages except the 132-ball chip-scale package (CP132 and CPG132). The markings for the BGA packages are nearly identical to those for the quad-flat packages, except that the marking is rotated with respect to the ball A1 indicator. Figure 4 shows the top marking for Spartan-3E FPGAs in the CP132 and CPG132 packages.

The “5C” and “4I” part combinations can have a dual mark of “5C/4I”. Devices with a single mark are only guaranteed for the marked speed grade and temperature range. All “5C” and “4I” part combinations use the Stepping 1 production silicon.

X-Ref Target - Figure 2

Mask Revision Code Fabrication Code R

SPARTAN

R

Process Technology

Device Type Package

XC3S250E TM PQ208AGQ0525 D1234567A

Date Code Stepping Code (optional)

Speed Grade

4C

Lot Code

Temperature Range

Pin P1

DS312-1_06_102905

Figure 2: Spartan-3E QFP Package Marking Example X-Ref Target - Figure 3

Mask Revision Code

BGA Ball A1

R

SPARTAN

Fabrication Code Process Code

R

XC3S250ETM FT256AGQ0525 D1234567A 4C

Device Type Package

Date Code Stepping Code (optional)

Lot Code

Speed Grade Temperature Range DS312-1_02_090105

Figure 3: Spartan-3E BGA Package Marking Example X-Ref Target - Figure 4

Ball A1 Lot Code

3S250E F1234567-0525 PHILIPPINES

Package C5 = CP132 C6 = CPG132

C5AGQ

Mask Revision Code

Device Type Date Code Temperature Range

4C Speed Grade Process Code Fabrication Code DS312-1_05_032105

Figure 4: Spartan-3E CP132 and CPG132 Package Marking Example

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 5

Spartan-3E FPGA Family: Introduction and Ordering Information

Ordering Information Spartan-3E FPGAs are available in both standard and Pb-free packaging options for all device/package combinations. All devices are available in Pb-free packages, which adds a ‘G’ character to the ordering code. All devices are available in either Commercial (C) or Industrial (I)

Example:

temperature ranges. Both the standard –4 and faster –5 speed grades are available for the Commercial temperature range. However, only the –4 speed grade is available for the Industrial temperature range. See Table 2 for valid device/package combinations.

XC3S250E -4 FT 256 C S1 (optional code to specify Stepping 1)

Device Type

Device

Speed Grade

Temperature Range

Package Type

Number of Pins

Speed Grade

DS312_03_082409

Package Type / Number of Pins

Temperature Range (TJ )

XC3S100E

-4 Standard Performance

VQ100 VQG100

100-pin Very Thin Quad Flat Pack (VQFP)

C Commercial (0°C to 85°C)

XC3S250E

-5 High Performance(1)

CP132 CPG132

132-ball Chip-Scale Package (CSP)

I Industrial (–40°C to 100°C)

XC3S500E(2)

TQ144 TQG144

144-pin Thin Quad Flat Pack (TQFP)

XC3S1200E

PQ208 PQG208

208-pin Plastic Quad Flat Pack (PQFP)

XC3S1600E

FT256 FTG256

256-ball Fine-Pitch Thin Ball Grid Array (FTBGA)

FG320 FGG320

320-ball Fine-Pitch Ball Grid Array (FBGA)

FG400 FGG400

400-ball Fine-Pitch Ball Grid Array (FBGA)

FG484 FGG484

484-ball Fine-Pitch Ball Grid Array (FBGA)

Notes: 1. 2. 3.

The -5 speed grade is exclusively available in the Commercial temperature range. The XC3S500E VQG100 is available only in the -4 Speed Grade. See DS635 for the XA Automotive Spartan-3E FPGAs.

Production Stepping The Spartan-3E FPGA family uses production stepping to indicate improved capabilities or enhanced features. Stepping 1 is, by definition, a functional superset of Stepping 0. Furthermore, configuration bitstreams generated for any stepping are forward compatible. See Table 72 for additional details. Xilinx has shipped both Stepping 0 and Stepping 1. Designs operating on the Stepping 0 devices perform similarly on a Stepping 1 device. Stepping 1 devices have been shipping since 2006. The faster speed grade (-5), Industrial (I grade), Automotive devices, and -4C devices with date codes 0901 (2009) and later, are always Stepping 1 devices. Only -4C devices have shipped as Stepping 0 devices.

Table 3: Spartan-3E Optional Stepping Level Ordering Stepping Number

Suffix Code

Status

0

None or S0

Production

1

S1

Production

The stepping level is optionally marked on the device using a single number character, as shown in Figure 2, Figure 3, and Figure 4.

To specify only the later stepping for the -4C, append an S# suffix to the standard ordering code, where # is the stepping number, as indicated in Table 3. DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 6

Spartan-3E FPGA Family: Introduction and Ordering Information

Revision History The following table shows the revision history for this document. Date

Version

Revision

03/01/2005

1.0

Initial Xilinx release.

03/21/2005

1.1

Added XC3S250E in CP132 package to Table 2. Corrected number of differential I/O pairs for CP132 package. Added package markings for QFP packages (Figure 2) and CP132/CPG132 packages (Figure 4).

11/23/2005

2.0

Added differential HSTL and SSTL I/O standards. Updated Table 2 to indicate number of input-only pins. Added Production Stepping information, including example top marking diagrams.

03/22/2006

3.0

Upgraded data sheet status to Preliminary. Added XC3S100E in CP132 package and updated I/O counts for the XC3S1600E in FG320 package (Table 2). Added information about dual markings for –5C and –4I product combinations to Package Marking.

11/09/2006

3.4

Added 66 MHz PCI support and links to the Xilinx PCI LogiCORE data sheet. Indicated that Stepping 1 parts are Production status. Promoted Module 1 to Production status. Synchronized all modules to v3.4.

04/18/2008

3.7

Added XC3S500E VQG100 package. Added reference to XA Automotive version. Updated links.

08/26/2009

3.8

Added paragraph to Configuration indicating the device supports MultiBoot configuration. Added package sizes to Table 2. Described the speed grade and temperature range guarantee for devices having a single mark in paragraph 3 under Package Marking. Deleted Pb-Free Packaging example under Ordering Information. Revised information under Production Stepping. Revised description of Table 3.

10/29/2012

4.0

Added Notice of Disclaimer. This product is not recommended for new designs. Updated Table 2 footprint size of PQ208.

07/19/2013

4.1

Removed banner. This product IS recommended for new designs.

Notice of Disclaimer THE XILINX HARDWARE FPGA AND CPLD DEVICES REFERRED TO HEREIN (“PRODUCTS”) ARE SUBJECT TO THE TERMS AND CONDITIONS OF THE XILINX LIMITED WARRANTY WHICH CAN BE VIEWED AT http://www.xilinx.com/warranty.htm. THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY USE OF PRODUCTS IN AN APPLICATION OR ENVIRONMENT THAT IS NOT WITHIN THE SPECIFICATIONS STATED IN THE XILINX DATA SHEET. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, OR ANY OTHER APPLICATION THAT INVOKES THE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). USE OF PRODUCTS IN CRITICAL APPLICATIONS IS AT THE SOLE RISK OF CUSTOMER, SUBJECT TO APPLICABLE LAWS AND REGULATIONS. CRITICAL APPLICATIONS DISCLAIMER XILINX PRODUCTS (INCLUDING HARDWARE, SOFTWARE AND/OR IP CORES) ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS IN LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, CLASS III MEDICAL DEVICES, NUCLEAR FACILITIES, APPLICATIONS RELATED TO THE DEPLOYMENT OF AIRBAGS, OR ANY OTHER APPLICATIONS THAT COULD LEAD TO DEATH, PERSONAL INJURY OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (INDIVIDUALLY AND COLLECTIVELY, “CRITICAL APPLICATIONS”). FURTHERMORE, XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN ANY APPLICATIONS THAT AFFECT CONTROL OF A VEHICLE OR AIRCRAFT, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE OPERATOR. CUSTOMER AGREES, PRIOR TO USING OR DISTRIBUTING ANY SYSTEMS THAT INCORPORATE XILINX PRODUCTS, TO THOROUGHLY TEST THE SAME FOR SAFETY PURPOSES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN CRITICAL APPLICATIONS.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 7

Spartan-3E FPGA Family: Introduction and Ordering Information AUTOMOTIVE APPLICATIONS DISCLAIMER XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS APPLICATIONS RELATED TO: (I) THE DEPLOYMENT OF AIRBAGS, (II) CONTROL OF A VEHICLE, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE OPERATOR, OR (III) USES THAT COULD LEAD TO DEATH OR PERSONAL INJURY. CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN SUCH APPLICATIONS.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 8

114

Spartan-3E FPGA Family: Functional Description

DS312 (v4.1) July 19, 2013

Product Specification

Design Documentation Available

Xilinx Alerts

The functionality of the Spartan®-3E FPGA family is now described and updated in the following documents. The topics covered in each guide are listed below.

Create a Xilinx user account and sign up to receive automatic e-mail notification whenever this data sheet or the associated user guides are updated.



Sign Up for Alerts on Xilinx.com http://secure.xilinx.com/webreg/register.do ?group=myprofile&languageID=1

UG331: Spartan-3 Generation FPGA User Guide •

Clocking Resources



Digital Clock Managers (DCMs)



Block RAM



Configurable Logic Blocks (CLBs) -



Spartan-3E FPGA Starter Kit For specific hardware examples, please see the Spartan-3E FPGA Starter Kit board web page, which has links to various design examples and the user guide.

Distributed RAM SRL16 Shift Registers Carry and Arithmetic Logic



I/O Resources



Embedded Multiplier Blocks



Programmable Interconnect



ISE® Design Tools



IP Cores



Embedded Processing and Control Solutions



Pin Types and Package Overview



Package Drawings



Powering FPGAs



Power Management



Spartan-3E FPGA Starter Kit Board page http://www.xilinx.com/s3estarter



UG230: Spartan-3E FPGA Starter Kit User Guide

UG332: Spartan-3 Generation Configuration User Guide •

Configuration Overview -



Configuration Pins and Behavior Bitstream Sizes

Detailed Descriptions by Mode -

Master Serial Mode using Xilinx® Platform Flash PROM Master SPI Mode using Commodity SPI Serial Flash PROM Master BPI Mode using Commodity Parallel NOR Flash PROM Slave Parallel (SelectMAP) using a Processor Slave Serial using a Processor JTAG Mode



ISE iMPACT Programming Examples



MultiBoot Reconfiguration

© Copyright 2005–2013 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Spartan, ISE, Artix, Kintex, Zynq, Vivado, and other designated brands included herein are trademarks of Xilinx in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 9

Spartan-3E FPGA Family: Functional Description

Introduction As described in Architectural Overview, the Spartan-3E FPGA architecture consists of five fundamental functional elements: •

Input/Output Blocks (IOBs)



Configurable Logic Block (CLB) and Slice Resources



Block RAM



Dedicated Multipliers



Digital Clock Managers (DCMs)

pair of storage elements to the IQ1 and IQ2 lines. The IOB outputs I, IQ1, and IQ2 lead to the FPGA’s internal logic. The delay element can be set to ensure a hold time of zero (see Input Delay Functions). •

The output path, starting with the O1 and O2 lines, carries data from the FPGA’s internal logic through a multiplexer and then a three-state driver to the IOB pad. In addition to this direct path, the multiplexer provides the option to insert a pair of storage elements.



The 3-state path determines when the output driver is high impedance. The T1 and T2 lines carry data from the FPGA’s internal logic through a multiplexer to the output driver. In addition to this direct path, the multiplexer provides the option to insert a pair of storage elements.



All signal paths entering the IOB, including those associated with the storage elements, have an inverter option. Any inverter placed on these paths is automatically absorbed into the IOB.

The following sections provide detailed information on each of these functions. In addition, this section also describes the following functions: •

Clocking Infrastructure



Interconnect



Configuration



Powering Spartan-3E FPGAs

Input/Output Blocks (IOBs) For additional information, refer to the “Using I/O Resources” chapter in UG331.

IOB Overview The Input/Output Block (IOB) provides a programmable, unidirectional or bidirectional interface between a package pin and the FPGA’s internal logic. The IOB is similar to that of the Spartan-3 family with the following differences: •

Input-only blocks are added



Programmable input delays are added to all blocks



DDR flip-flops can be shared between adjacent IOBs

The unidirectional input-only block has a subset of the full IOB capabilities. Thus there are no connections or logic for an output path. The following paragraphs assume that any reference to output functionality does not apply to the input-only blocks. The number of input-only blocks varies with device size, but is never more than 25% of the total IOB count. Figure 5 is a simplified diagram of the IOB’s internal structure. There are three main signal paths within the IOB: the output path, input path, and 3-state path. Each path has its own pair of storage elements that can act as either registers or latches. For more information, see Storage Element Functions. The three main signal paths are as follows: •

The input path carries data from the pad, which is bonded to a package pin, through an optional programmable delay element directly to the I line. After the delay element, there are alternate routes through a

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 10

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 5

T T1

D

Q

TFF1

CE CK SR

REV DDR MUX

TCE T2

D

Q TFF2

CE CK SR

REV Three-state Path

O1 OTCLK1

D CE CK SR

Q

Pull-Up

OTCLK2

ESD

REV I/O Pin

DDR MUX

OCE O2

VCCO

OFF1

D CE

Programmable Output Driver

Q OFF2

PullDown

ESD

CK SR

REV Keeper Latch

Output Path Programmable Delay

I IQ1 IDDRIN1 IDDRIN2 ICLK1 ICE

LVCMOS, LVTTL, PCI

Programmable Delay D

Q

VREF Pin

IFF1

CE CK SR

Single-ended Standards using VREF

REV

Differential Standards I/O Pin from Adjacent IOB

IQ2 D

Q IFF2

CE ICLK2

CK SR

REV

SR REV

Input Path DS312-2_19_110606

Figure 5: Simplified IOB Diagram

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 11

Spartan-3E FPGA Family: Functional Description

Input Delay Functions Each IOB has a programmable delay block that optionally delays the input signal. In Figure 6, the signal path has a coarse delay element that can be bypassed. The input signal then feeds a 6-tap delay line. The coarse and tap delays vary; refer to timing reports for specific delay values. All six taps are available via a multiplexer for use as an asynchronous input directly into the FPGA fabric. In this way, the delay is programmable in 12 steps. Three of the six taps are also available via a multiplexer to the D inputs of the synchronous storage elements. The delay inserted in the path to the storage element can be varied in six steps. The first, coarse delay element is common to both asynchronous and synchronous paths, and must be either used or not used for both paths. The delay values are set up in the silicon once at configuration time—they are non-modifiable in device operation. The primary use for the input delay element is to adjust the input delay path to ensure that there is no hold time requirement when using the input flip-flop(s) with a global clock. The default value is chosen automatically by the Xilinx software tools as the value depends on device size and the specific device edge where the flip-flop resides. The value set by the Xilinx ISE software is indicated in the Map

report generated by the implementation tools, and the resulting effects on input timing are reported using the Timing Analyzer tool. If the design uses a DCM in the clock path, then the delay element can be safely set to zero because the Delay-Locked Loop (DLL) compensation automatically ensures that there is still no input hold time requirement. Both asynchronous and synchronous values can be modified, which is useful where extra delay is required on clock or data inputs, for example, in interfaces to various types of RAM. These delay values are defined through the IBUF_DELAY_VALUE and the IFD_DELAY_VALUE parameters. The default IBUF_DELAY_VALUE is 0, bypassing the delay elements for the asynchronous input. The user can set this parameter to 0-12. The default IFD_DELAY_VALUE is AUTO. IBUF_DELAY_VALUE and IFD_DELAY_VALUE are independent for each input. If the same input pin uses both registered and non-registered input paths, both parameters can be used, but they must both be in the same half of the total delay (both either bypassing or using the coarse delay element).

X-Ref Target - Figure 6

IFD_DELAY_VALUE Synchronous input (IQ1) D Q Synchronous input (IQ2) D Q

Coarse Delay PAD

Asynchronous input (I) IBUF_DELAY_VALUE UG331_c10_09_011508

Figure 6: Programmable Fixed Input Delay Elements

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 12

Spartan-3E FPGA Family: Functional Description

Storage Element Functions There are three pairs of storage elements in each IOB, one pair for each of the three paths. It is possible to configure each of these storage elements as an edge-triggered D-type flip-flop (FD) or a level-sensitive latch (LD). The storage-element pair on either the Output path or the Three-State path can be used together with a special multiplexer to produce Double-Data-Rate (DDR) transmission. This is accomplished by taking data

synchronized to the clock signal’s rising edge and converting it to bits synchronized on both the rising and the falling edge. The combination of two registers and a multiplexer is referred to as a Double-Data-Rate D-type flip-flop (ODDR2). Table 4 describes the signal paths associated with the storage element.

Table 4: Storage Element Signal Description Storage Element Signal

Description

Function

D

Data input

Data at this input is stored on the active edge of CK and enabled by CE. For latch operation when the input is enabled, data passes directly to the output Q.

Q

Data output

The data on this output reflects the state of the storage element. For operation as a latch in transparent mode, Q mirrors the data at D.

CK

Clock input

Data is loaded into the storage element on this input’s active edge with CE asserted.

CE

Clock Enable input

When asserted, this input enables CK. If not connected, CE defaults to the asserted state.

SR

Set/Reset input

This input forces the storage element into the state specified by the SRHIGH/SRLOW attributes. The SYNC/ASYNC attribute setting determines if the SR input is synchronized to the clock or not. If both SR and REV are active at the same time, the storage element gets a value of 0.

REV

Reverse input

This input is used together with SR. It forces the storage element into the state opposite from what SR does. The SYNC/ASYNC attribute setting determines whether the REV input is synchronized to the clock or not. If both SR and REV are active at the same time, the storage element gets a value of 0.

As shown in Figure 5, the upper registers in both the output and three-state paths share a common clock. The OTCLK1 clock signal drives the CK clock inputs of the upper registers on the output and three-state paths. Similarly, OTCLK2 drives the CK inputs for the lower registers on the output and three-state paths. The upper and lower registers on the input path have independent clock lines: ICLK1 and ICLK2. The OCE enable line controls the CE inputs of the upper and lower registers on the output path. Similarly, TCE

controls the CE inputs for the register pair on the three-state path and ICE does the same for the register pair on the input path. The Set/Reset (SR) line entering the IOB controls all six registers, as is the Reverse (REV) line. In addition to the signal polarity controls described in IOB Overview, each storage element additionally supports the controls described in Table 5.

Table 5: Storage Element Options Option Switch

Function

Specificity

FF/Latch

Chooses between an edge-triggered flip-flop or a level-sensitive latch

Independent for each storage element

SYNC/ASYNC

Determines whether the SR set/reset control is synchronous or asynchronous

Independent for each storage element

SRHIGH/SRLOW

Determines whether SR acts as a Set, which forces the storage element to a logic 1 (SRHIGH) or a Reset, which forces a logic 0 (SRLOW)

Independent for each storage element, except when using ODDR2. In the latter case, the selection for the upper element will apply to both elements.

INIT1/INIT0

When Global Set/Reset (GSR) is asserted or after configuration this option specifies the initial state of the storage element, either set (INIT1) or reset (INIT0). By default, choosing SRLOW also selects INIT0; choosing SRHIGH also selects INIT1.

Independent for each storage element, except when using ODDR2, which uses two IOBs. In the ODDR2 case, selecting INIT0 for one IOBs applies to both elements within the IOB, although INIT1 could be selected for the elements in the other IOB.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 13

Spartan-3E FPGA Family: Functional Description

Double-Data-Rate Transmission The storage-element pair on the Three-State path (TFF1 and TFF2) also can be combined with a local multiplexer to form a DDR primitive. This permits synchronizing the output enable to both the rising and falling edges of a clock. This DDR operation is realized in the same way as for the output path.

Double-Data-Rate (DDR) transmission describes the technique of synchronizing signals to both the rising and falling edges of the clock signal. Spartan-3E devices use register pairs in all three IOB paths to perform DDR operations. The pair of storage elements on the IOB’s Output path (OFF1 and OFF2), used as registers, combine with a special multiplexer to form a DDR D-type flip-flop (ODDR2). This primitive permits DDR transmission where output data bits are synchronized to both the rising and falling edges of a clock. DDR operation requires two clock signals (usually 50% duty cycle), one the inverted form of the other. These signals trigger the two registers in alternating fashion, as shown in Figure 7. The Digital Clock Manager (DCM) generates the two clock signals by mirroring an incoming signal, and then shifting it 180 degrees. This approach ensures minimal skew between the two signals. Alternatively, the inverter inside the IOB can be used to invert the clock signal, thus only using one clock line and both rising and falling edges of that clock line as the two clocks for the DDR flip-flops.

The storage-element pair on the input path (IFF1 and IFF2) allows an I/O to receive a DDR signal. An incoming DDR clock signal triggers one register, and the inverted clock signal triggers the other register. The registers take turns capturing bits of the incoming DDR data signal. The primitive to allow this functionality is called IDDR2. Aside from high bandwidth data transfers, DDR outputs also can be used to reproduce, or mirror, a clock signal on the output. This approach is used to transmit clock and data signals together (source synchronously). A similar approach is used to reproduce a clock signal at multiple outputs. The advantage for both approaches is that skew across the outputs is minimal.

X-Ref Target - Figure 7

DCM 180˚ 0˚

DCM 0˚ FDDR

FDDR

D1

D1 Q1

Q1

CLK1

CLK1 DDR MUX

DDR MUX

Q

D2

Q

D2 Q2

Q2

CLK2

CLK2

DS312-2_20_021105

Figure 7: Two Methods for Clocking the DDR Register

Register Cascade Feature

IDDR2

In the Spartan-3E family, one of the IOBs in a differential pair can cascade its input storage elements with those in the other IOB as part of a differential pair. This is intended to make DDR operation at high speed much simpler to implement. The new DDR connections that are available are shown in Figure 5 (dashed lines), and are only available for routing between IOBs and are not accessible to the FPGA fabric. Note that this feature is only available when using the differential I/O standards LVDS, RSDS, and MINI_LVDS.

As a DDR input pair, the master IOB registers incoming data on the rising edge of ICLK1 (= D1) and the rising edge of ICLK2 (= D2), which is typically the same as the falling edge of ICLK1. This data is then transferred into the FPGA fabric. At some point, both signals must be brought into the same clock domain, typically ICLK1. This can be difficult at high frequencies because the available time is only one half of a clock cycle assuming a 50% duty cycle. See Figure 8 for a graphical illustration of this function.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 14

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 8

D

Q

D1

PAD

To Fabric D

Q

D2

ICLK2 ICLK1

The C0 or C1 alignment feature of the ODDR2 flip-flop, originally introduced in the Spartan-3E FPGA family, is not recommended or supported in the ISE development software. The ODDR2 flip-flop without the alignment feature remains fully supported. Without the alignment feature, the ODDR2 feature behaves equivalent to the ODDR flip-flop on previous Xilinx FPGA families.

ICLK1 ICLK2 PAD

d

d+1 d+2 d+3 d+4 d+5 d

D1 D2

d+2

d-1

d+1

d+6 d+7 d+8

d+4 d+3

d+6

d+8

d+5

and the rising edge of OCLK2 (= D2), which is typically the same as the falling edge of OCLK1. These two bits of data are multiplexed by the DDR mux and forwarded to the output pin. The D2 data signal must be re-synchronized from the OCLK1 clock domain to the OCLK2 domain using FPGA slice flip-flops. Placement is critical at high frequencies, because the time available is only one half a clock cycle. See Figure 10 for a graphical illustration of this function.

X-Ref Target - Figure 10

d+7

Q

D

D1

PAD

DS312-2_21_021105

From Fabric

Figure 8: Input DDR (without Cascade Feature) In the Spartan-3E device, the signal D2 can be cascaded into the storage element of the adjacent slave IOB. There it is re-registered to ICLK1, and only then fed to the FPGA fabric where it is now already in the same time domain as D1. Here, the FPGA fabric uses only the clock ICLK1 to process the received data. See Figure 9 for a graphical illustration of this function.

D2

Q

D

OCLK1 OCLK2

X-Ref Target - Figure 9

OCLK1 D

Q

D1

OCLK2

PAD

D1

To Fabric

D

Q

D2

IDDRIN2

IQ2

D

Q

D2

PAD

d

d+2 d+1

d+4 d+3

d

d+1

d+2

d+6 d+5

d+3

d+8

d+9

d+7 d+4

d+5

d+10

d+6

d+7

d+8

DS312-2_23_030105

Figure 10: Output DDR

ICLK1 ICLK2

The Spartan-3E I/Os feature inputs and outputs that support a wide range of I/O signaling standards (Table 6 and Table 7). The majority of the I/Os also can be used to form differential pairs to support any of the differential signaling standards (Table 7).

ICLK1 ICLK2 PAD

d

d+1

d+2

d+3

d+4

d+5

d+6

d+7

SelectIO Signal Standards

d+8

D1

d

d+2

d+4

d+6

d+8

D2

d-1

d+1

d+3

d+5

d+7

DS312-2_22_030105

Figure 9: Input DDR Using Spartan-3E Cascade Feature

ODDR2

To define the I/O signaling standard in a design, set the IOSTANDARD attribute to the appropriate setting. Xilinx provides a variety of different methods for applying the IOSTANDARD for maximum flexibility. For a full description of different methods of applying attributes to control IOSTANDARD, refer to the Xilinx Software Manuals and Help.

As a DDR output pair, the master IOB registers data coming from the FPGA fabric on the rising edge of OCLK1 (= D1) DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 15

Spartan-3E FPGA Family: Functional Description Spartan-3E FPGAs provide additional input flexibility by allowing I/O standards to be mixed in different banks. For a particular VCCO voltage, Table 6 and Table 7 list all of the

IOSTANDARDs that can be combined and if the IOSTANDARD is supported as an input only or can be used for both inputs and outputs.

Table 6: Single-Ended IOSTANDARD Bank Compatibility VCCO Supply/Compatibility Single-Ended IOSTANDARD

Input Requirements VREF

Board Termination Voltage (VTT)

1.2V

1.5V

1.8V

2.5V

3.3V

LVTTL

-

-

-

-

Input/ Output

N/R(1)

N/R

LVCMOS33

-

-

-

-

Input/ Output

N/R

N/R

LVCMOS25

-

-

-

Input/ Output

Input

N/R

N/R

LVCMOS18

-

-

Input/ Output

Input

Input

N/R

N/R

LVCMOS15

-

Input/ Output

Input

Input

Input

N/R

N/R

LVCMOS12

Input/ Output

Input

Input

Input

Input

N/R

N/R

PCI33_3

-

-

-

-

Input/ Output

N/R

N/R

PCI66_3

-

-

-

-

Input/ Output

N/R

N/R

HSTL_I_18

-

-

Input/ Output

Input

Input

0.9

0.9

HSTL_III_18

-

-

Input/ Output

Input

Input

1.1

1.8

SSTL18_I

-

-

Input/ Output

Input

Input

0.9

0.9

SSTL2_I

-

-

-

Input/ Output

Input

1.25

1.25

Notes: 1.

N/R - Not required for input operation.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 16

Spartan-3E FPGA Family: Functional Description

Table 7: Differential IOSTANDARD Bank Compatibility VCCO Supply

Differential IOSTANDARD

Input Requirements: VREF

Differential Bank Restriction(1)

1.8V

2.5V

3.3V

LVDS_25

Input

Input, On-chip Differential Termination, Output

Input

Applies to Outputs Only

RSDS_25

Input

Input

Applies to Outputs Only

MINI_LVDS_25

Input

Input

Applies to Outputs Only

LVPECL_25

Input

BLVDS_25

Input

DIFF_HSTL_I_18 DIFF_HSTL_III_18 DIFF_SSTL18_I

Input, Output Input, Output Input, Output

DIFF_SSTL2_I

Input

Input, On-chip Differential Termination, Output Input, On-chip Differential Termination, Output Input Input, Output

Input

Input

Input

Input

Input

Input

Input

Input, Output

Input

Input

VREF is not used for these I/O standards No Differential Bank Restriction (other I/O bank restrictions might apply)

Notes: 1.

Each bank can support any two of the following: LVDS_25 outputs, MINI_LVDS_25 outputs, RSDS_25 outputs.

HSTL and SSTL inputs use the Reference Voltage (VREF) to bias the input-switching threshold. Once a configuration data file is loaded into the FPGA that calls for the I/Os of a given bank to use HSTL/SSTL, a few specifically reserved I/O pins on the same bank automatically convert to VREF inputs. For banks that do not contain HSTL or SSTL, VREF pins remain available for user I/Os or input pins. Differential standards employ a pair of signals, one the opposite polarity of the other. The noise canceling properties (for example, Common-Mode Rejection) of these standards permit exceptionally high data transfer rates. This subsection introduces the differential signaling capabilities of Spartan-3E devices. Each device-package combination designates specific I/O pairs specially optimized to support differential standards. A unique L-number, part of the pin name, identifies the line-pairs associated with each bank (see Module 4, Pinout Descriptions). For each pair, the letters P and N designate the true and inverted lines, respectively. For example, the pin names IO_L43P_3 and IO_L43N_3 indicate the true and inverted lines comprising the line pair L43 on Bank 3.

On-Chip Differential Termination Spartan-3E devices provide an on-chip ~120Ω differential termination across the input differential receiver terminals. The on-chip input differential termination in Spartan-3E devices potentially eliminates the external 100Ω termination resistor commonly found in differential receiver circuits. Differential termination is used for LVDS, mini-LVDS, and RSDS as applications permit. On-chip Differential Termination is available in banks with VCCO = 2.5V and is not supported on dedicated input pins. Set the DIFF_TERM attribute to TRUE to enable Differential Termination on a differential I/O pin pair. The DIFF_TERM attribute uses the following syntax in the UCF file: INST DIFF_TERM = "";

VCCO provides current to the outputs and additionally powers the On-Chip Differential Termination. VCCO must be 2.5V when using the On-Chip Differential Termination. The VREF lines are not required for differential operation. To further understand how to combine multiple IOSTANDARDs within a bank, refer to IOBs Organized into Banks, page 19. DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 17

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 11

X-Ref Target - Figure 12

Spartan-3E Differential Input

Z0 = 50Ω

Pull-up

100Ω

Spartan-3E Differential Output

Output Path

Z0 = 50Ω

Z0 = 50Ω ~120Ω

Spartan-3E Differential Output

Input Path Spartan-3E Differential Input with On-Chip Differential Terminator

Keeper Pull-down DS312-2_25_020807

Figure 12: Keeper Circuit

Z0 = 50Ω

Slew Rate Control and Drive Strength DS312-2_24_082605

Each IOB has a slew-rate control that sets the output switching edge-rate for LVCMOS and LVTTL outputs. The SLEW attribute controls the slew rate and can either be set to SLOW (default) or FAST.

Figure 11: Differential Inputs and Outputs

Pull-Up and Pull-Down Resistors Pull-up and pull-down resistors inside each IOB optionally force a floating I/O or Input-only pin to a determined state. Pull-up and pull-down resistors are commonly applied to unused I/Os, inputs, and three-state outputs, but can be used on any I/O or Input-only pin. The pull-up resistor connects an IOB to VCCO through a resistor. The resistance value depends on the VCCO voltage (see Module 3, DC and Switching Characteristics for the specifications). The pull-down resistor similarly connects an IOB to ground with a resistor. The PULLUP and PULLDOWN attributes and library primitives turn on these optional resistors. By default, PULLDOWN resistors terminate all unused I/O and Input-only pins. Unused I/O and Input-only pins can alternatively be set to PULLUP or FLOAT. To change the unused I/O Pad setting, set the Bitstream Generator (BitGen) option UnusedPin to PULLUP, PULLDOWN, or FLOAT. The UnusedPin option is accessed through the Properties for Generate Programming File in ISE. See Bitstream Generator (BitGen) Options. During configuration a Low logic level on the HSWAP pin activates pull-up resistors on all I/O and Input-only pins not actively used in the selected configuration mode.

Keeper Circuit Each I/O has an optional keeper circuit (see Figure 12) that keeps bus lines from floating when not being actively driven. The KEEPER circuit retains the last logic level on a line after all drivers have been turned off. Apply the KEEPER attribute or use the KEEPER library primitive to use the KEEPER circuitry. Pull-up and pull-down resistors override the KEEPER settings.

DS312 (v4.1) July 19, 2013 Product Specification

Each LVCMOS and LVTTL output additionally supports up to six different drive current strengths as shown in Table 8. To adjust the drive strength for each output, the DRIVE attribute is set to the desired drive strength: 2, 4, 6, 8, 12, and 16. Unless otherwise specified in the FPGA application, the software default IOSTANDARD is LVCMOS25, SLOW slew rate, and 12 mA output drive. Table 8: Programmable Output Drive Current IOSTANDARD

Output Drive Current (mA) 2

4

6

8

12

16

LVTTL













LVCMOS33













LVCMOS25











-

LVCMOS18









-

-

LVCMOS15







-

-

-

LVCMOS12



-

-

-

-

-

High output current drive strength and FAST output slew rates generally result in fastest I/O performance. However, these same settings generally also result in transmission line effects on the printed circuit board (PCB) for all but the shortest board traces. Each IOB has independent slew rate and drive strength controls. Use the slowest slew rate and lowest output drive current that meets the performance requirements for the end application. Likewise, due to lead inductance, a given package supports a limited number of simultaneous switching outputs (SSOs) when using fast, high-drive outputs. Only use fast, high-drive outputs when required by the application.

www.xilinx.com 18

Spartan-3E FPGA Family: Functional Description

IOBs Organized into Banks The Spartan-3E architecture organizes IOBs into four I/O banks as shown in Figure 13. Each bank maintains separate VCCO and VREF supplies. The separate supplies allow each bank to independently set VCCO. Similarly, the VREF supplies can be set for each bank. Refer to Table 6 and Table 7 for VCCO and VREF requirements. When working with Spartan-3E devices, most of the differential I/O standards are compatible and can be combined within any given bank. Each bank can support any two of the following differential standards: LVDS_25 outputs, MINI_LVDS_25 outputs, and RSDS_25 outputs. As an example, LVDS_25 outputs, RSDS_25 outputs, and any other differential inputs while using on-chip differential termination are a valid combination. A combination not allowed is a single bank with LVDS_25 outputs, RSDS_25 outputs, and MINI_LVDS_25 outputs. X-Ref Target - Figure 13

Bank 1

Bank 3

Bank 0

1. All VREF pins must be connected within a bank. 2. All VREF lines associated with the bank must be set to the same voltage level. 3. The VREF levels used by all standards assigned to the Inputs of the bank must agree. The Xilinx development software checks for this. Table 6 describes how different standards use the VREF supply. If VREF is not required to bias the input switching thresholds, all associated VREF pins within the bank can be used as user I/Os or input pins.

Package Footprint Compatibility Sometimes, applications outgrow the logic capacity of a specific Spartan-3E FPGA. Fortunately, the Spartan-3E family is designed so that multiple part types are available in pin-compatible package footprints, as described in Module 4, Pinout Descriptions. In some cases, there are subtle differences between devices available in the same footprint. These differences are outlined for each package, such as pins that are unconnected on one device but connected on another in the same package or pins that are dedicated inputs on one package but full I/O on another. When designing the printed circuit board (PCB), plan for potential future upgrades and package migration. The Spartan-3E family is not pin-compatible with any previous Xilinx FPGA family.

Bank 2

Dedicated Inputs DS312-2_26_021205

Figure 13: Spartan-3E I/O Banks (top view)

I/O Banking Rules When assigning I/Os to banks, these VCCO rules must be followed: 1. All VCCO pins on the FPGA must be connected even if a bank is unused. 2. All VCCO lines associated within a bank must be set to the same voltage level. 3. The VCCO levels used by all standards assigned to the I/Os of any given bank must agree. The Xilinx development software checks for this. Table 6 and Table 7 describe how different standards use the VCCO supply. 4. If a bank does not have any VCCO requirements, connect VCCO to an available voltage, such as 2.5V or 3.3V. Some configuration modes might place additional VCCO requirements. Refer to Configuration for more information. If any of the standards assigned to the Inputs of the bank use VREF, then the following additional rules must be observed:

DS312 (v4.1) July 19, 2013 Product Specification

Dedicated Inputs are IOBs used only as inputs. Pin names designate a Dedicated Input if the name starts with IP, for example, IP or IP_Lxxx_x. Dedicated inputs retain the full functionality of the IOB for input functions with a single exception for differential inputs (IP_Lxxx_x). For the differential Dedicated Inputs, the on-chip differential termination is not available. To replace the on-chip differential termination, choose a differential pair that supports outputs (IO_Lxxx_x) or use an external 100Ω termination resistor on the board.

ESD Protection Clamp diodes protect all device pads against damage from Electro-Static Discharge (ESD) as well as excessive voltage transients. Each I/O has two clamp diodes: one diode extends P-to-N from the pad to VCCO and a second diode extends N-to-P from the pad to GND. During operation, these diodes are normally biased in the off state. These clamp diodes are always connected to the pad, regardless of the signal standard selected. The presence of diodes limits the ability of Spartan-3E I/Os to tolerate high signal voltages. The VIN absolute maximum rating in Table 73 of Module 3, DC and Switching Characteristics specifies the voltage range that I/Os can tolerate.

www.xilinx.com 19

Spartan-3E FPGA Family: Functional Description

Supply Voltages for the IOBs The IOBs are powered by three supplies: 1. The VCCO supplies, one for each of the FPGA’s I/O banks, power the output drivers. The voltage on the VCCO pins determines the voltage swing of the output signal. 2. VCCINT is the main power supply for the FPGA’s internal logic. 3. VCCAUX is an auxiliary source of power, primarily to optimize the performance of various FPGA functions such as I/O switching.

I/O and Input-Only Pin Behavior During Power-On, Configuration, and User Mode In this section, all behavior described for I/O pins also applies to input-only pins and dual-purpose I/O pins that are not actively involved in the currently-selected configuration mode. All I/O pins have ESD clamp diodes to their respective VCCO supply and from GND, as shown in Figure 5. The VCCINT (1.2V), VCCAUX (2.5V), and VCCO supplies can be applied in any order. Before the FPGA can start its configuration process, VCCINT, VCCO Bank 2, and VCCAUX must have reached their respective minimum recommended operating levels indicated in Table 74. At this time, all output drivers are in a high-impedance state. VCCO Bank 2, VCCINT, and VCCAUX serve as inputs to the internal Power-On Reset circuit (POR).

beginning of design operation in the User mode. After the GTS net is released, all user I/Os go active while all unused I/Os are pulled down (PULLDOWN). The designer can control how the unused I/Os are terminated after GTS is released by setting the Bitstream Generator (BitGen) option UnusedPin to PULLUP, PULLDOWN, or FLOAT. One clock cycle later (default), the Global Write Enable (GWE) net is released allowing the RAM and registers to change states. Once in User mode, any pull-up resistors enabled by HSWAP revert to the user settings and HSWAP is available as a general-purpose I/O. For more information on PULLUP and PULLDOWN, see Pull-Up and Pull-Down Resistors.

Behavior of Unused I/O Pins After Configuration By default, the Xilinx ISE development software automatically configures all unused I/O pins as input pins with individual internal pull-down resistors to GND. This default behavior is controlled by the UnusedPin bitstream generator (BitGen) option, as described in Table 69.

JTAG Boundary-Scan Capability All Spartan-3E IOBs support boundary-scan testing compatible with IEEE 1149.1/1532 standards. During boundary-scan operations such as EXTEST and HIGHZ the pull-down resistor is active. See JTAG Mode for more information on programming via JTAG.

A Low level applied to the HSWAP input enables pull-up resistors on user-I/O and input-only pins from power-on throughout configuration. A High level on HSWAP disables the pull-up resistors, allowing the I/Os to float. HSWAP contains an internal pull-up resistor and defaults to High if left floating. As soon as power is applied, the FPGA begins initializing its configuration memory. At the same time, the FPGA internally asserts the Global Set-Reset (GSR), which asynchronously resets all IOB storage elements to a default Low state. Also see Pin Behavior During Configuration. Upon the completion of initialization and the beginning of configuration, INIT_B goes High, sampling the M0, M1, and M2 inputs to determine the configuration mode. Configuration data is then loaded into the FPGA. The I/O drivers remain in a high-impedance state (with or without pull-up resistors, as determined by the HSWAP input) throughout configuration. At the end of configuration, the GSR net is released, placing the IOB registers in a Low state by default, unless the loaded design reverses the polarity of their respective SR inputs. The Global Three State (GTS) net is released during Start-Up, marking the end of configuration and the

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 20

Spartan-3E FPGA Family: Functional Description

Configurable Logic Block (CLB) and Slice Resources

(SRL16), and additional multiplexers and carry logic simplify wide logic and arithmetic functions. Most general-purpose logic in a design is automatically mapped to the slice resources in the CLBs. Each CLB is identical, and the Spartan-3E family CLB structure is identical to that for the Spartan-3 family.

For additional information, refer to the “Using Configurable Logic Blocks (CLBs)” chapter in UG331.

CLB Overview

CLB Array

The Configurable Logic Blocks (CLBs) constitute the main logic resource for implementing synchronous as well as combinatorial circuits. Each CLB contains four slices, and each slice contains two Look-Up Tables (LUTs) to implement logic and two dedicated storage elements that can be used as flip-flops or latches. The LUTs can be used as a 16x1 memory (RAM16) or as a 16-bit shift register

The CLBs are arranged in a regular array of rows and columns as shown in Figure 14. Each density varies by the number of rows and columns of CLBs (see Table 9).

X-Ref Target - Figure 14

Spartan-3E FPGA

X0Y3

X1Y3

X2Y3

X3Y3

X0Y2

X1Y2

X2Y2

X3Y2

X0Y1

X1Y1

X2Y1

X3Y1

X0Y0

X1Y0

X2Y0

X3Y0

IOBs

Slice

CLB

DS312-2_31_021205

Figure 14: CLB Locations Table 9: Spartan-3E CLB Resources CLB Rows

CLB Columns

Slices

LUTs / Flip-Flops

Equivalent Logic Cells

RAM16 / SRL16

Distributed RAM Bits

XC3S100E

22

16

240

960

1,920

2,160

960

15,360

XC3S250E

34

26

612

2,448

4,896

5,508

2,448

39,168

XC3S500E

46

34

1,164

4,656

9,312

10,476

4,656

74,496

XC3S1200E

60

46

2,168

8,672

17,344

19,512

8,672

138,752

XC3S1600E

76

58

3,688

14,752

29,504

33,192

14,752

236,032

Device

CLB Total(1)

Notes: 1.

The number of CLBs is less than the multiple of the rows and columns because the block RAM/multiplier blocks and the DCMs are embedded in the array (see Figure 1 in Module 1).

Slices Each CLB comprises four interconnected slices, as shown in Figure 16. These slices are grouped in pairs. Each pair is organized as a column with an independent carry chain. The left pair supports both logic and memory functions and its slices are called SLICEM. The right pair supports logic only and its slices are called SLICEL. Therefore half the DS312 (v4.1) July 19, 2013 Product Specification

LUTs support both logic and memory (including both RAM16 and SRL16 shift registers) while half support logic only, and the two types alternate throughout the array columns. The SLICEL reduces the size of the CLB and lowers the cost of the device, and can also provide a performance advantage over the SLICEM.

www.xilinx.com 21

Spartan-3E FPGA Family: Functional Description . X-Ref Target - Figure 15

WS

DI

DI D

WF[4:1]

DS312-2_32_042007

Notes: 1. 2.

Options to invert signal polarity as well as other options that enable lines for various functions are not shown. The index i can be 6, 7, or 8, depending on the slice. The upper SLICEL has an F8MUX, and the upper SLICEM has an F7MUX. The lower SLICEL and SLICEM both have an F6MUX.

Figure 15: Simplified Diagram of the Left-Hand SLICEM DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 22

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 16

Left-Hand SLICEM (Logic or Distributed RAM or Shift Register)

Right-Hand SLICEL (Logic Only) COUT

CLB SLICE X1Y1

SLICE X1Y0 COUT

Switch Matrix

Interconnect to Neighbors

CIN SLICE X0Y1 SHIFTOUT SHIFTIN SLICE X0Y0

CIN

DS099-2_05_082104

Figure 16: Arrangement of Slices within the CLB

Slice Location Designations

Slice Overview

The Xilinx development software designates the location of a slice according to its X and Y coordinates, starting in the bottom left corner, as shown in Figure 14. The letter ‘X’ followed by a number identifies columns of slices, incrementing from the left side of the die to the right. The letter ‘Y’ followed by a number identifies the position of each slice in a pair as well as indicating the CLB row, incrementing from the bottom of the die. Figure 16 shows the CLB located in the lower left-hand corner of the die. The SLICEM always has an even ‘X’ number, and the SLICEL always has an odd ‘X’ number.

A slice includes two LUT function generators and two storage elements, along with additional logic, as shown in Figure 17. Both SLICEM and SLICEL have the following elements in common to provide logic, arithmetic, and ROM functions: •

Two 4-input LUT function generators, F and G



Two storage elements



Two wide-function multiplexers, F5MUX and FiMUX



Carry and arithmetic logic

X-Ref Target - Figure 17

SRL16 RAM16 LUT4 (G)

FiMUX Carry

FiMUX LUT4 (G)

Register

F5MUX SRL16 RAM16 LUT4 (F)

Carry

Carry

Register

F5MUX Carry

Register

Register

LUT4 (F) Arithmetic Logic

Arithmetic Logic

SLICEM

SLICEL

DS312-2_13_020905

Figure 17: Resources in a Slice

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 23

Spartan-3E FPGA Family: Functional Description Enable (CE), Slice Write Enable (SLICEWE1), and Reset/Set (RS) are shared in common between the two halves.

The SLICEM pair supports two additional functions: •

Two 16x1 distributed RAM blocks, RAM16



Two 16-bit shift registers, SRL16

Each of these elements is described in more detail in the following sections.

Logic Cells The combination of a LUT and a storage element is known as a “Logic Cell”. The additional features in a slice, such as the wide multiplexers, carry logic, and arithmetic gates, add to the capacity of a slice, implementing logic that would otherwise require additional LUTs. Benchmarks have shown that the overall slice is equivalent to 2.25 simple logic cells. This calculation provides the equivalent logic cell count shown in Table 9.

Slice Details Figure 15 is a detailed diagram of the SLICEM. It represents a superset of the elements and connections to be found in all slices. The dashed and gray lines (blue when viewed in color) indicate the resources found only in the SLICEM and not in the SLICEL. Each slice has two halves, which are differentiated as top and bottom to keep them distinct from the upper and lower slices in a CLB. The control inputs for the clock (CLK), Clock

The LUTs located in the top and bottom portions of the slice are referred to as “G” and “F”, respectively, or the “G-LUT” and the “F-LUT”. The storage elements in the top and bottom portions of the slice are called FFY and FFX, respectively. Each slice has two multiplexers with F5MUX in the bottom portion of the slice and FiMUX in the top portion. Depending on the slice, the FiMUX takes on the name F6MUX, F7MUX, or F8MUX, according to its position in the multiplexer chain. The lower SLICEL and SLICEM both have an F6MUX. The upper SLICEM has an F7MUX, and the upper SLICEL has an F8MUX. The carry chain enters the bottom of the slice as CIN and exits at the top as COUT. Five multiplexers control the chain: CYINIT, CY0F, and CYMUXF in the bottom portion and CY0G and CYMUXG in the top portion. The dedicated arithmetic logic includes the exclusive-OR gates XORF and XORG (bottom and top portions of the slice, respectively) as well as the AND gates FAND and GAND (bottom and top portions, respectively). See Table 10 for a description of all the slice input and output signals.

Table 10: Slice Inputs and Outputs Name

Location

Direction

Description

F[4:1]

SLICEL/M Bottom

Input

F-LUT and FAND inputs

G[4:1]

SLICEL/M Top

Input

G-LUT and GAND inputs or Write Address (SLICEM)

BX

SLICEL/M Bottom

Input

Bypass to or output (SLICEM) or storage element, or control input to F5MUX, input to carry logic, or data input to RAM (SLICEM)

BY

SLICEL/M Top

Input

Bypass to or output (SLICEM) or storage element, or control input to FiMUX, input to carry logic, or data input to RAM (SLICEM)

BXOUT

SLICEM Bottom

Output

BX bypass output

BYOUT

SLICEM Top

Output

BY bypass output

ALTDIG

SLICEM Top

Input

DIG

SLICEM Top

Output

SLICEWE1

SLICEM Common

Input

F5

SLICEL/M Bottom

Output

FXINA

SLICEL/M Top

Input

Input to FiMUX; direct feedback from F5MUX or another FiMUX

FXINB

SLICEL/M Top

Input

Input to FiMUX; direct feedback from F5MUX or another FiMUX

Fi

SLICEL/M Top

Output

CE

SLICEL/M Common

Input

FFX/Y Clock Enable

SR

SLICEL/M Common

Input

FFX/Y Set or Reset or RAM Write Enable (SLICEM)

CLK

SLICEL/M Common

Input

FFX/Y Clock or RAM Clock (SLICEM)

SHIFTIN

SLICEM Top

Input

Data input to G-LUT RAM

DS312 (v4.1) July 19, 2013 Product Specification

Alternate data input to RAM ALTDIG or SHIFTIN bypass output RAM Write Enable Output from F5MUX; direct feedback to FiMUX

Output from FiMUX; direct feedback to another FiMUX

www.xilinx.com 24

Spartan-3E FPGA Family: Functional Description Table 10: Slice Inputs and Outputs (Cont’d) Name

Location

Direction Output

Description

SHIFTOUT

SLICEM Bottom

CIN

SLICEL/M Bottom

COUT

SLICEL/M Top

Output

Carry chain output

X

SLICEL/M Bottom

Output

Combinatorial output

Y

SLICEL/M Top

Output

Combinatorial output

XB

SLICEL/M Bottom

Output

Combinatorial output from carry or F-LUT SRL16 (SLICEM)

YB

SLICEL/M Top

Output

Combinatorial output from carry or G-LUT SRL16 (SLICEM)

XQ

SLICEL/M Bottom

Output

FFX output

YQ

SLICEL/M Top

Output

FFY output

Input

Shift data output from F-LUT RAM Carry chain input

Main Logic Paths

2. Bypass the LUT, and then pass through a storage element via the D input before exiting as XQ (or YQ).

Central to the operation of each slice are two nearly identical data paths at the top and bottom of the slice. The description that follows uses names associated with the bottom path. (The top path names appear in parentheses.) The basic path originates at an interconnect switch matrix outside the CLB. See Interconnect for more information on the switch matrix and the routing connections. Four lines, F1 through F4 (or G1 through G4 on the upper path), enter the slice and connect directly to the LUT. Once inside the slice, the lower 4-bit path passes through a LUT ‘F’ (or ‘G’) that performs logic operations. The LUT Data output, ‘D’, offers five possible paths: 1. Exit the slice via line “X” (or “Y”) and return to interconnect. 2. Inside the slice, “X” (or “Y”) serves as an input to the DXMUX (or DYMUX) which feeds the data input, “D”, of the FFX (or FFY) storage element. The “Q” output of the storage element drives the line XQ (or YQ) which exits the slice. 3. Control the CYMUXF (or CYMUXG) multiplexer on the carry chain. 4. With the carry chain, serve as an input to the XORF (or XORG) exclusive-OR gate that performs arithmetic operations, producing a result on “X” (or “Y”). 5. Drive the multiplexer F5MUX to implement logic functions wider than four bits. The “D” outputs of both the F-LUT and G-LUT serve as data inputs to this multiplexer. In addition to the main logic paths described above, there are two bypass paths that enter the slice as BX and BY. Once inside the FPGA, BX in the bottom half of the slice (or BY in the top half) can take any of several possible branches:

3. Control the wide function multiplexer F5MUX (or FiMUX). 4. Via multiplexers, serve as an input to the carry chain. 5. Drive the DI input of the LUT. 6. BY can control the REV inputs of both the FFY and FFX storage elements. See Storage Element Functions. 7. Finally, the DIG_MUX multiplexer can switch BY onto the DIG line, which exits the slice. The control inputs CLK, CE, SR, BX and BY have programmable polarity. The LUT inputs do not need programmable polarity because their function can be inverted inside the LUT. The sections that follow provide more detail on individual functions of the slice.

Look-Up Tables The Look-Up Table or LUT is a RAM-based function generator and is the main resource for implementing logic functions. Furthermore, the LUTs in each SLICEM pair can be configured as Distributed RAM or a 16-bit shift register, as described later. Each of the two LUTs (F and G) in a slice have four logic inputs (A1-A4) and a single output (D). Any four-variable Boolean logic operation can be implemented in one LUT. Functions with more inputs can be implemented by cascading LUTs or by using the wide function multiplexers that are described later. The output of the LUT can connect to the wide multiplexer logic, the carry and arithmetic logic, or directly to a CLB output or to the CLB storage element. See Figure 18.

1. Bypass both the LUT and the storage element, and then exit the slice as BXOUT (or BYOUT) and return to interconnect. DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 25

Spartan-3E FPGA Family: Functional Description

Wide Multiplexers

X-Ref Target - Figure 18

Y

For additional information, refer to the “Using Dedicated Multiplexers” chapter in UG331.

4 G[4:1]

D

A[4:1]

YQ

FFY

Wide-function multiplexers effectively combine LUTs in order to permit more complex logic operations. Each slice has two of these multiplexers with F5MUX in the bottom portion of the slice and FiMUX in the top portion. The F5MUX multiplexes the two LUTs in a slice. The FiMUX multiplexes two CLB inputs which connect directly to the F5MUX and FiMUX results from the same slice or from other slices. See Figure 19.

G-LUT

X F[4:1]

4 A[4:1]

D

XQ

FFX

F-LUT

DS312-2_33_111105

Figure 18: LUT Resources in a Slice X-Ref Target - Figure 19

FiMUX FXINA

1

FXINB

0

FX (Local Feedback to FXIN) Y (General Interconnect)

BY D Q

YQ

F5MUX F[4:1]

LUT

1

G[4:1]

LUT

0

F5 (Local Feedback to FXIN) X (General Interconnect)

BX D Q

XQ

x312-2_34_021205

Figure 19: Dedicated Multiplexers in Spartan-3E CLB Depending on the slice, FiMUX takes on the name F6MUX, F7MUX, or F8MUX. The designation indicates the number of inputs possible without restriction on the function. For example, an F7MUX can generate any function of seven inputs. Figure 20 shows the names of the multiplexers in each position in the Spartan-3E CLB. The figure also includes the direct connections within the CLB, along with the F7MUX connection to the CLB below. Each mux can create logic functions of more inputs than indicated by its name. The F5MUX, for example, can generate any function of five inputs, with four inputs duplicated to two LUTs and the fifth input controlling the mux. Because each LUT can implement independent 2:1 muxes, the F5MUX can combine them to create a 4:1 mux, which is a six-input function. If the two LUTs have completely independent sets of inputs, some functions of all nine inputs can be implemented. Table 11 shows the connections for each multiplexer and the number of inputs possible for different types of functions.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 26

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 20

FXINB F8

X

F5

F5

FXINA

FXINB

FX

F6 FXINA

F5

F5

FXINB FXINA

FX

F7

F5

F5

F6

FX

F5

F5

FXINB FXINA

DS312-2_38_021305

Figure 20: MUXes and Dedicated Feedback in Spartan-3E CLB Table 11: MUX Capabilities Total Number of Inputs per Function MUX

Usage

Input Source

F5MUX

F5MUX

FiMUX

For Any Function

For MUX

For Limited Functions

LUTs

5

6 (4:1 MUX)

9

F6MUX

F5MUX

6

11 (8:1 MUX)

19

F7MUX

F6MUX

7

20 (16:1 MUX)

39

F8MUX

F7MUX

8

37 (32:1 MUX)

79

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 27

Spartan-3E FPGA Family: Functional Description The wide multiplexers can be used by the automatic tools or instantiated in a design using a component such as the F5MUX. The symbol, signals, and function are described in Figure 21, Table 12, and Table 13. The description is similar for the F6MUX, F7MUX, and F8MUX. Each has versions with a general output, local output, or both. X-Ref Target - Figure 21

I0

0

I1

1

LO O

S DS312-2_35_021205

Figure 21: F5MUX with Local and General Outputs Table 12: F5MUX Inputs and Outputs Signal

Function

I0

Input selected when S is Low

I1

Input selected when S is High

S

Select input

LO

Local Output that connects to the F5 or FX CLB pins, which use local feedback to the FXIN inputs to the FiMUX for cascading

O

General Output that connects to the general-purpose combinatorial or registered outputs of the CLB

Table 13: F5MUX Function Inputs

Outputs

S

I0

I1

O

LO

0

1

X

1

1

0

0

X

0

0

1

X

1

1

1

1

X

0

0

0

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 28

Spartan-3E FPGA Family: Functional Description

Carry and Arithmetic Logic For additional information, refer to the “Using Carry and Arithmetic Logic” chapter in UG331.

The carry chain enters the slice as CIN and exits as COUT, controlled by several multiplexers. The carry chain connects directly from one CLB to the CLB above. The carry chain can be initialized at any point from the BX (or BY) inputs.

The carry chain, together with various dedicated arithmetic logic gates, support fast and efficient implementations of math operations. The carry logic is automatically used for most arithmetic functions in a design. The gates and multiplexers of the carry and arithmetic logic can also be used for general-purpose logic, including simple wide Boolean functions.

The dedicated arithmetic logic includes the exclusive-OR gates XORF and XORG (upper and lower portions of the slice, respectively) as well as the AND gates GAND and FAND (upper and lower portions, respectively). These gates work in conjunction with the LUTs to implement efficient arithmetic functions, including counters and multipliers, typically at two bits per slice. See Figure 22 and Table 14.

X-Ref Target - Figure 22

COUT

YB 1 G[4:1]

CYMUXG

A[4:1] G1

G2

Y

CYSELG

G-LUT YQ

D XORG

FFY

CY0G

GAND

1 0

BY

XB 1 4 F[4:1]

CYMUXF

A[4:1] F1

F2

X

CYSELF

F-LUT XQ

D XORF

FFX

CY0F

FAND

1 0

CYINIT

BX

CIN

DS312-2_14_021305

Figure 22: Carry Logic Table 14: Carry Logic Functions Function

Description

CYINIT

Initializes carry chain for a slice. Fixed selection of: · CIN carry input from the slice below · BX input

CY0F

Carry generation for bottom half of slice. Fixed selection of: · F1 or F2 inputs to the LUT (both equal 1 when a carry is to be generated) · FAND gate for multiplication · BX input for carry initialization · Fixed 1 or 0 input for use as a simple Boolean function

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 29

Spartan-3E FPGA Family: Functional Description Table 14: Carry Logic Functions (Cont’d) Function

Description

CY0G

Carry generation for top half of slice. Fixed selection of: · G1 or G2 inputs to the LUT (both equal 1 when a carry is to be generated) · GAND gate for multiplication · BY input for carry initialization · Fixed 1 or 0 input for use as a simple Boolean function

CYMUXF

Carry generation or propagation mux for bottom half of slice. Dynamic selection via CYSELF of: · CYINIT carry propagation (CYSELF = 1) · CY0F carry generation (CYSELF = 0)

CYMUXG

Carry generation or propagation mux for top half of slice. Dynamic selection via CYSELF of: · CYMUXF carry propagation (CYSELG = 1) · CY0G carry generation (CYSELG = 0)

CYSELF

Carry generation or propagation select for bottom half of slice. Fixed selection of: · F-LUT output (typically XOR result) · Fixed 1 to always propagate

CYSELG

Carry generation or propagation select for top half of slice. Fixed selection of: · G-LUT output (typically XOR result) · Fixed 1 to always propagate

XORF

Sum generation for bottom half of slice. Inputs from: · F-LUT · CYINIT carry signal from previous stage Result is sent to either the combinatorial or registered output for the top of the slice.

XORG

Sum generation for top half of slice. Inputs from: · G-LUT · CYMUXF carry signal from previous stage Result is sent to either the combinatorial or registered output for the top of the slice.

FAND

Multiplier partial product for bottom half of slice. Inputs: · F-LUT F1 input · F-LUT F2 input Result is sent through CY0F to become the carry generate signal into CYMUXF

GAND

Multiplier partial product for top half of slice. Inputs: · G-LUT G1 input · G-LUT G2 input Result is sent through CY0G to become the carry generate signal into CYMUXG

The basic usage of the carry logic is to generate a half-sum in the LUT via an XOR function, which generates or propagates a carry out COUT via the carry mux CYMUXF (or CYMUXG), and then complete the sum with the dedicated XORF (or XORG) gate and the carry input CIN. This structure allows two bits of an arithmetic function in each slice. The CYMUXF (or CYMUXG) can be instantiated using the MUXCY element, and the XORF (or XORG) can be instantiated using the XORCY element. The FAND (or GAND) gate is used for partial product multiplication and can be instantiated using the MULT_AND component. Partial products are generated by two-input AND gates and then added. The carry logic is efficient for the adder, but one of the inputs must be outside the LUT as shown in Figure 23.

DS312 (v4.1) July 19, 2013 Product Specification

X-Ref Target - Figure 23

LUT

COUT

B MUXCY

A

Sum XORCY CIN DS312-2_37_021305

Figure 23: Using the MUXCY and XORCY in the Carry Logic The FAND (or GAND) gate is used to duplicate one of the partial products, while the LUT generates both partial products and the XOR function, as shown in Figure 24.

www.xilinx.com 30

Spartan-3E FPGA Family: Functional Description

Storage Elements

X-Ref Target - Figure 24

LUT COUT

Am Bn+1

The storage element, which is programmable as either a D-type flip-flop or a level-sensitive transparent latch, provides a means for synchronizing data to a clock signal, among other uses. The storage elements in the top and bottom portions of the slice are called FFY and FFX, respectively. FFY has a fixed multiplexer on the D input selecting either the combinatorial output Y or the bypass signal BY. FFX selects between the combinatorial output X or the bypass signal BX.

Am+1 Bn Pm+1 MULT_AND

CIN

DS312-2_39_021305

Figure 24: Using the MULT_AND for Multiplication in Carry Logic

The functionality of a slice storage element is identical to that described earlier for the I/O storage elements. All signals have programmable polarity; the default active-High function is described.

The MULT_AND is useful for small multipliers. Larger multipliers can be built using the dedicated 18x18 multiplier blocks (see Dedicated Multipliers). Table 15: Storage Element Signals Signal

Description

D

Input. For a flip-flop data on the D input is loaded when R and S (or CLR and PRE) are Low and CE is High during the Low-to-High clock transition. For a latch, Q reflects the D input while the gate (G) input and gate enable (GE) are High and R and S (or CLR and PRE) are Low. The data on the D input during the High-to-Low gate transition is stored in the latch. The data on the Q output of the latch remains unchanged as long as G or GE remains Low.

Q

Output. Toggles after the Low-to-High clock transition for a flip-flop and immediately for a latch.

C

Clock for edge-triggered flip-flops.

G

Gate for level-sensitive latches.

CE

Clock Enable for flip-flops.

GE

Gate Enable for latches.

S

Synchronous Set (Q = High). When the S input is High and R is Low, the flip-flop is set, output High, during the Low-to-High clock (C) transition. A latch output is immediately set, output High.

R

Synchronous Reset (Q = Low); has precedence over Set.

PRE

Asynchronous Preset (Q = High). When the PRE input is High and CLR is Low, the flip-flop is set, output High, during the Low-to-High clock (C) transition. A latch output is immediately set, output High.

CLR

Asynchronous Clear (Q = Low); has precedence over Preset to reset Q output Low

SR

CLB input for R, S, CLR, or PRE

REV

CLB input for opposite of SR. Must be asynchronous or synchronous to match SR.

The control inputs R, S, CE, and C are all shared between the two flip-flops in a slice.

Table 16: FD Flip-Flop Functionality with Synchronous Reset, Set, and Clock Enable Inputs

X-Ref Target - Figure 25

S FDRSE D CE C

Q

R DS312-2_40_021305

Figure 25: FD Flip-Flop Component with Synchronous Reset, Set, and Clock Enable

DS312 (v4.1) July 19, 2013 Product Specification

Outputs

R

S

CE

D

C

Q

1

X

X

X



0

0

1

X

X



1

0

0

0

X

X

No Change

0

0

1

1



1

0

0

1

0



0

www.xilinx.com 31

Spartan-3E FPGA Family: Functional Description

Initialization

Distributed RAM

The CLB storage elements are initialized at power-up, during configuration, by the global GSR signal, and by the individual SR or REV inputs to the CLB. The storage elements can also be re-initialized using the GSR input on the STARTUP_SPARTAN3E primitive. See Global Controls (STARTUP_SPARTAN3E).

For additional information, refer to the “Using Look-Up Tables as Distributed RAM” chapter in UG331.

Table 17: Slice Storage Element Initialization Signal

Description

SR

Set/Reset input. Forces the storage element into the state specified by the attribute SRHIGH or SRLOW. SRHIGH forces a logic 1 when SR is asserted. SRLOW forces a logic 0. For each slice, set and reset can be set to be synchronous or asynchronous.

REV

Reverse of Set/Reset input. A second input (BY) forces the storage element into the opposite state. The reset condition is predominant over the set condition if both are active. Same synchronous/asynchronous setting as for SR.

GSR

Global Set/Reset. GSR defaults to active High but can be inverted by adding an inverter in front of the GSR input of the STARTUP_SPARTAN3E element. The initial state after configuration or GSR is defined by a separate INIT0 and INIT1 attribute. By default, setting the SRLOW attribute sets INIT0, and setting the SRHIGH attribute sets INIT1.

The LUTs in the SLICEM can be programmed as distributed RAM. This type of memory affords moderate amounts of data buffering anywhere along a data path. One SLICEM LUT stores 16 bits (RAM16). The four LUT inputs F[4:1] or G[4:1] become the address lines labeled A[4:1] in the device model and A[3:0] in the design components, providing a 16x1 configuration in one LUT. Multiple SLICEM LUTs can be combined in various ways to store larger amounts of data, including 16x4, 32x2, or 64x1 configurations in one CLB. The fifth and sixth address lines required for the 32-deep and 64-deep configurations, respectively, are implemented using the BX and BY inputs, which connect to the write enable logic for writing and the F5MUX and F6MUX for reading. Writing to distributed RAM is always synchronous to the SLICEM clock (WCLK for distributed RAM) and enabled by the SLICEM SR input which functions as the active-High Write Enable (WE). The read operation is asynchronous, and, therefore, during a write, the output initially reflects the old data at the address being written. The distributed RAM outputs can be captured using the flip-flops within the SLICEM element. The WE write-enable control for the RAM and the CE clock-enable control for the flip-flop are independent, but the WCLK and CLK clock inputs are shared. Because the RAM read operation is asynchronous, the output data always reflects the currently addressed RAM location. A dual-port option combines two LUTs so that memory access is possible from two independent data lines. The same data is written to both 16x1 memories but they have independent read address lines and outputs. The dual-port function is implemented by cascading the G-LUT address lines, which are used for both read and write, to the F-LUT write address lines (WF[4:1] in Figure 15), and by cascading the G-LUT data input D1 through the DIF_MUX in Figure 15 and to the D1 input on the F-LUT. One CLB provides a 16x1 dual-port memory as shown in Figure 26. Any write operation on the D input and any read operation on the SPO output can occur simultaneously with and independently from a read operation on the second read-only port, DPO.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 32

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 26

SLICEM 16x1 LUT RAM

D A[3:0]

SPO

(Read/ Write)

Optional Register

WE WCLK

DPO

16x1 LUT RAM

DPRA[3:0]

Optional Register

(Read Only)

DS312-2_41_021305

Figure 26: RAM16X1D Dual-Port Usage Table 19: Distributed RAM Signals

X-Ref Target - Figure 27

RAM16X1D WE D WCLK A0 A1 A2 A3 DPRA0 DPRA1 DPRA2 DPRA3

Signal

SPO DPO

WCLK

The clock is used for synchronous writes. The data and the address input pins have setup times referenced to the WCLK pin. Active on the positive edge by default with built-in programmable polarity.

WE

The enable pin affects the write functionality of the port. An inactive Write Enable prevents any writing to memory cells. An active Write Enable causes the clock edge to write the data input signal to the memory location pointed to by the address inputs. Active High by default with built-in programmable polarity.

A0, A1, A2, A3 (A4, A5)

The address inputs select the memory cells for read or write. The width of the port determines the required address inputs.

D

The data input provides the new data value to be written into the RAM.

O, SPO, and DPO

The data output O on single-port RAM or the SPO and DPO outputs on dual-port RAM reflects the contents of the memory cells referenced by the address inputs. Following an active write clock edge, the data out (O or SPO) reflects the newly written data.

DS312-2_42_021305

Figure 27: Dual-Port RAM Component Table 18: Dual-Port RAM Function Inputs

Outputs

WE (mode)

WCLK

D

SPO

DPO

0 (read)

X

X

data_a

data_d

1 (read)

0

X

data_a

data_d

1 (read)

1

X

data_a

data_d

1 (write)



D

D

data_d

1 (read)



X

data_a

data_d

Notes: 1. 2.

data_a = word addressed by bits A3-A0. data_d = word addressed by bits DPRA3-DPRA0.

Description

The INIT attribute can be used to preload the memory with data during FPGA configuration. The default initial contents for RAM is all zeros. If the WE is held Low, the element can be considered a ROM. The ROM function is possible even in the SLICEL. The global write enable signal, GWE, is asserted automatically at the end of device configuration to enable all writable elements. The GWE signal guarantees that the

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 33

Spartan-3E FPGA Family: Functional Description initialized distributed RAM contents are not disturbed during the configuration process.

X-Ref Target - Figure 29

SRLC16E D CE CLK A0 A1 A2 A3

The distributed RAM is useful for smaller amounts of memory. Larger memory requirements can use the dedicated 18Kbit RAM blocks (see Block RAM).

Shift Registers

DS312-2_43_021305

For additional information, refer to the “Using Look-Up Tables as Shift Registers (SRL16)” chapter in UG331. It is possible to program each SLICEM LUT as a 16-bit shift register (see Figure 28). Used in this way, each LUT can delay serial data anywhere from 1 to 16 clock cycles without using any of the dedicated flip-flops. The resulting programmable delays can be used to balance the timing of data pipelines. The SLICEM LUTs cascade from the G-LUT to the F-LUT through the DIFMUX (see Figure 15). SHIFTIN and SHIFTOUT lines cascade a SLICEM to the SLICEM below to form larger shift registers. The four SLICEM LUTs of a single CLB can be combined to produce delays up to 64 clock cycles. It is also possible to combine shift registers across more than one CLB.

Figure 29: SRL16 Shift Register Component with Cascade and Clock Enable The functionality of the shift register is shown in Table 20. The SRL16 shifts on the rising edge of the clock input when the Clock Enable control is High. This shift register cannot be initialized either during configuration or during operation except by shifting data into it. The clock enable and clock inputs are shared between the two LUTs in a SLICEM. The clock enable input is automatically kept active if unused. Table 20: SRL16 Shift Register Function Inputs

X-Ref Target - Figure 28

SRLC16

SHIFTIN

Q Q15

Outputs

Am

CLK

CE

D

Q

Q15

Am

X

0

X

Q[Am]

Q[15]

Am



1

D

Q[Am-1]

Q[15]

Notes: 1.

SHIFT-REG A[3:0]

4

A[3:0]

D MC15

WS

DI

m = 0, 1, 2, 3.

Output D

Q

Registered Output

DI (BY) WSG CE (SR) CLK

(optional)

WE CK

SHIFTOUT or YB

X465_03_040203

Figure 28: Logic Cell SRL16 Structure Each shift register provides a shift output MC15 for the last bit in each LUT, in addition to providing addressable access to any bit in the shift register through the normal D output. The address inputs A[3:0] are the same as the distributed RAM address lines, which come from the LUT inputs F[4:1] or G[4:1]. At the end of the shift register, the CLB flip-flop can be used to provide one more shift delay for the addressable bit. The shift register element is known as the SRL16 (Shift Register LUT 16-bit), with a ‘C’ added to signify a cascade ability (Q15 output) and ‘E’ to indicate a Clock Enable. See Figure 29 for an example of the SRLC16E component.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 34

Spartan-3E FPGA Family: Functional Description

Block RAM

and write operations. There are four basic data paths, as shown in Figure 30:

For additional information, refer to the “Using Block RAM” chapter in UG331.

1. Write to and read from Port A 2. Write to and read from Port B 3. Data transfer from Port A to Port B 4. Data transfer from Port B to Port A X-Ref Target - Figure 30

Read 3

Write 4 Read

Each block RAM is configurable by setting the content’s initial values, default signal value of the output registers, port aspect ratios, and write modes. Block RAM can be used in single-port or dual-port modes.

Spartan-3E Dual-Port Block RAM

Port B

Write

Port A

Spartan-3E devices incorporate 4 to 36 dedicated block RAMs, which are organized as dual-port configurable 18 Kbit blocks. Functionally, the block RAM is identical to the Spartan-3 architecture block RAM. Block RAM synchronously stores large amounts of data while distributed RAM, previously described, is better suited for buffering small amounts of data anywhere along signal paths. This section describes basic block RAM functions.

Write

Write

Read

Read

2

1

Arrangement of RAM Blocks on Die The block RAMs are located together with the multipliers on the die in one or two columns depending on the size of the device. The XC3S100E has one column of block RAM. The Spartan-3E devices ranging from the XC3S250E to XC3S1600E have two columns of block RAM. Table 21 shows the number of RAM blocks, the data storage capacity, and the number of columns for each device. Row(s) of CLBs are located above and below each block RAM column. Table 21: Number of RAM Blocks by Device Total Number of RAM Blocks

Total Addressable Locations (bits)

Number of Columns

XC3S100E

4

73,728

1

XC3S250E

12

221,184

2

XC3S500E

20

368,640

2

XC3S1200E

28

516,096

2

XC3S1600E

36

663,552

2

Device

DS312-2_01_020705

Figure 30: Block RAM Data Paths

Number of Ports A choice among primitives determines whether the block RAM functions as dual- or single-port memory. A name of the form RAMB16_S[wA]_S[wB] calls out the dual-port primitive, where the integers wA and wB specify the total data path width at ports A and B, respectively. Thus, a RAMB16_S9_S18 is a dual-port RAM with a 9-bit Port A and an 18-bit Port B. A name of the form RAMB16_S[w] identifies the single-port primitive, where the integer w specifies the total data path width of the lone port A. A RAMB16_S18 is a single-port RAM with an 18-bit port.

Port Aspect Ratios Each port of the block RAM can be configured independently to select a number of different possible widths for the data input (DI) and data output (DO) signals as shown in Table 22.

Immediately adjacent to each block RAM is an embedded 18x18 hardware multiplier. The upper 16 bits of the block RAM's Port A Data input bus are shared with the upper 16 bits of the A multiplicand input bus of the multiplier. Similarly, the upper 16 bits of Port B's data input bus are shared with the B multiplicand input bus of the multiplier.

The Internal Structure of the Block RAM The block RAM has a dual port structure. The two identical data ports called A and B permit independent access to the common block RAM, which has a maximum capacity of 18,432 bits, or 16,384 bits with no parity bits (see parity bits description in Table 22). Each port has its own dedicated set of data, control, and clock lines for synchronous read

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 35

Spartan-3E FPGA Family: Functional Description

Table 22: Port Aspect Ratios Total Data Path Width (w bits)

DI/DO Data DIP/DOP ADDR Bus Width Parity Bus Bus Width (w-p bits)(1) Width (p bits) (r bits)(2)

DI/DO [w-p-1:0]

DIP/DOP [p-1:0]

ADDR [r-1:0]

No. of Addressable Locations (n)(3)

Block RAM Capacity (w*n bits)(4)

1

1

0

14

[0:0]

-

[13:0]

16,384

16,384

2

2

0

13

[1:0]

-

[12:0]

8,192

16,384

4

4

0

12

[3:0]

-

[11:0]

4,096

16,384

9

8

1

11

[7:0]

[0:0]

[10:0]

2,048

18,432

18

16

2

10

[15:0]

[1:0]

[9:0]

1,024

18,432

36

32

4

9

[31:0]

[3:0]

[8:0]

512

18,432

Notes: 1. 2. 3. 4.

The width of the total data path (w) is the sum of the DI/DO bus width (w-p) and any parity bits (p). The width selection made for the DI/DO bus determines the number of address lines (r) according to the relationship expressed as: r = 14 – [log(w–p)/log9(2)]. The number of address lines delimits the total number (n) of addressable locations or depth according to the following equation: n = 2r. The product of w and n yields the total block RAM capacity.

If the data bus width of Port A differs from that of Port B, the block RAM automatically performs a bus-matching function as described in Figure 31. When data is written to a port with a narrow bus and then read from a port with a wide bus, the latter port effectively combines “narrow” words to form “wide” words. Similarly, when data is written into a port with a wide bus and then read from a port with a narrow bus, the latter port divides “wide” words to form “narrow” words. Parity bits are not available if the data port width is configured as x4, x2, or x1. For example, if a x36 data word (32 data, 4 parity) is addressed as two x18 halfwords (16 data, 2 parity), the parity bits associated with each data byte are mapped within the block RAM to the appropriate parity bits. The same effect happens when the x36 data word is mapped as four x9 words.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 36

Spartan-3E FPGA Family: Functional Description X-Ref Target - Figure 31

Parity

Data

35 34 33 32 31

512x36

P3 P2 P1 P0

24 23

Byte 3

Address

16 15

Byte 2

8 7

Byte 1 17 16 15

1Kx18 Pa r (16 ity O K 2K bits ption bits a d pa ata, l rity )

0

Byte 0

0

8 7

0

P3 P2

Byte 3

Byte 2

P1 P0

Byte 1

Byte 0 8

2Kx9

1 0

7

0

P3

Byte 3

P2

Byte 2

P1

Byte 1

P0

Byte 0

3 2 1 0

3 2 1 0

7 6 5 34 y te1 0 3B 2

7 6

7 6 5 04 te 3B2y 1 0

1 0

4Kx4

1 0

6 4 2 0

F E D C

7 5 3 1

6 4 2 0

3 2 1 0

8Kx2 Byte 0

No Parity (16Kbits data)

Byte 3

7 5 3 1

Byte 3

0

7 6 5 4

1F 1E 1D 1C

3 2 1 0

3 2 1 0

Byte 0

16Kx1

DS312-2_02_102105

Figure 31: Data Organization and Bus-matching Operation with Different Port Widths on Port A and Port B

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 37

Spartan-3E FPGA Family: Functional Description

Block RAM Port Signal Definitions

Design Note

Representations of the dual-port primitive RAMB16_S[wA]_S[wB] and the single-port primitive RAMB16_S[w] with their associated signals are shown in Figure 32a and Figure 32b, respectively. These signals are defined in Table 23. The control signals (WE, EN, CLK, and SSR) on the block RAM are active High. However, optional inverters on the control signals change the polarity of the active edge to active Low.

Whenever a block RAM port is enabled (ENA or ENB = High), all address transitions must meet the data sheet setup and hold times with respect to the port clock (CLKA or CLKB), as shown in Table 103, page 139.This requirement must be met even if the RAM read output is of no interest.

X-Ref Target - Figure 32

WEA ENA SSRA CLKA ADDRA[rA–1:0] DIA[wA–pA–1:0] DIPA[pA–1:0]

RAMB16_SW _SW A

B

DOPA[pA–1:0] DOA[wA–pA–1:0]

WEB ENB SSRB CLKB ADDRB[rB–1:0] DIB[wB–pB–1:0] DIPB[pB–1:0]

DOPB[pB–1:0] DOB[wB–pB–1:0]

WE EN SSR CLK ADDR[r–1:0] DI[w–p–1:0] DIP[p–1:0]

(a) Dual-Port

RAMB16_Sw

DOP[p–1:0] DO[w–p–1:0]

(b) Single-Port DS312-2_03_111105

Notes: 1. 2. 3. 4.

wA and wB are integers representing the total data path width (i.e., data bits plus parity bits) at Ports A and B, respectively. pA and pB are integers that indicate the number of data path lines serving as parity bits. rA and rB are integers representing the address bus width at ports A and B, respectively. The control signals CLK, WE, EN, and SSR on both ports have the option of inverted polarity.

Figure 32: Block RAM Primitives

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 38

Spartan-3E FPGA Family: Functional Description

Table 23: Block RAM Port Signals Port A Signal Name

Port B Signal Name

Direction

Function

ADDRA

ADDRB

Input

The Address Bus selects a memory location for read or write operations. The width (w) of the port’s associated data path determines the number of available address lines (r), as per Table 22. Whenever a port is enabled (ENA or ENB = High), address transitions must meet the data sheet setup and hold times with respect to the port clock (CLKA or CLKB), as shown in Table 103, page 139.This requirement must be met even if the RAM read output is of no interest.

Data Input Bus

DIA

DIB

Input

Data at the DI input bus is written to the RAM location specified by the address input bus (ADDR) during the active edge of the CLK input, when the clock enable (EN) and write enable (WE) inputs are active. It is possible to configure a port’s DI input bus width (w-p) based on Table 22. This selection applies to both the DI and DO paths of a given port.

Parity Data Input(s)

DIPA

DIPB

Input

Parity inputs represent additional bits included in the data input path. Although referred to herein as “parity” bits, the parity inputs and outputs have no special functionality for generating or checking parity and can be used as additional data bits. The number of parity bits ‘p’ included in the DI (same as for the DO bus) depends on a port’s total data path width (w). See Table 22.

Data Output Bus

DOA

DOB

Output

Data is written to the DO output bus from the RAM location specified by the address input bus, ADDR. See the DI signal description for DO port width configurations. Basic data access occurs on the active edge of the CLK when WE is inactive and EN is active. The DO outputs mirror the data stored in the address ADDR memory location. Data access with WE active if the WRITE_MODE attribute is set to the value: WRITE_FIRST, which accesses data after the write takes place. READ_FIRST accesses data before the write occurs. A third attribute, NO_CHANGE, latches the DO outputs upon the assertion of WE. See Block RAM Data Operations for details on the WRITE_MODE attribute.

Parity Data Output(s)

DOPA

DOPB

Output

Parity outputs represent additional bits included in the data input path. The number of parity bits ‘p’ included in the DI bus (same as for the DO bus) depends on a port’s total data path width (w). See the DIP signal description for configuration details.

Write Enable

WEA

WEB

Input

When asserted together with EN, this input enables the writing of data to the RAM. When WE is inactive with EN asserted, read operations are still possible. In this case, a latch passes data from the addressed memory location to the DO outputs.

Clock Enable

ENA

ENB

Input

When asserted, this input enables the CLK signal to perform read and write operations to the block RAM. When inactive, the block RAM does not perform any read or write operations.

Set/Reset

SSRA

SSRB

Input

When asserted, this pin forces the DO output latch to the value of the SRVAL attribute. It is synchronized to the CLK signal.

Clock

CLKA

CLKB

Input

This input accepts the clock signal to which read and write operations are synchronized. All associated port inputs are required to meet setup times with respect to the clock signal’s active edge. The data output bus responds after a clock-to-out delay referenced to the clock signal’s active edge.

Signal Description Address Bus

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 39

Spartan-3E FPGA Family: Functional Description

Block RAM Attribute Definitions A block RAM has a number of attributes that control its behavior as shown in Table 24. Table 24: Block RAM Attributes Function

Attribute

Possible Values

Initial Content for Data Memory, Loaded during Configuration

INITxx (INIT_00 through INIT3F)

Each initialization string defines 32 hex values of the 16384-bit data memory of the block RAM.

INITPxx (INITP_00 through INITP0F)

Each initialization string defines 32 hex values of the 2048-bit parity data memory of the block RAM.

Initial Content for Parity Memory, Loaded during Configuration Data Output Latch Initialization

INIT (single-port) INITA, INITB (dual-port)

Data Output Latch Synchronous Set/Reset Value

Hex value the width of the chosen port.

SRVAL (single-port) Hex value the width of the chosen port. SRVAL_A, SRVAL_B (dual-port)

Data Output Latch Behavior during Write (see Block RAM Data Operations)

WRITE_FIRST, READ_FIRST, NO_CHANGE

WRITE_MODE

Block RAM Data Operations Writing data to and accessing data from the block RAM are synchronous operations that take place independently on each of the two ports. Table 25 describes the data operations of each port as a result of the block RAM control signals in their default active-High edges.

The waveforms for the write operation are shown in the top half of Figure 33, Figure 34, and Figure 35. When the WE and EN signals enable the active edge of CLK, data at the DI input bus is written to the block RAM location addressed by the ADDR lines.

Table 25: Block RAM Function Table Input Signals GSR

EN

SSR

WE

CLK

Output Signals ADDR

DIP

DI

DOP

RAM Data

DO

Parity

Data

X

INITP_xx

INIT_xx

INIT

No Chg

No Chg

No Chg

No Chg

No Chg

SRVAL

No Chg

No Chg

SRVAL

RAM(addr) ← pdata

RAM(addr) ← data

RAM(data)

No Chg

No Chg

Immediately After Configuration Loaded During Configuration

X

Global Set/Reset Immediately After Configuration 1

X

X

X

X

X

X

X

INIT

RAM Disabled 0

0

X

X

X

X

X

0

1

1

0



X

X

0

1

1

1



addr

0

1

0

0



addr

0

1

0

1



addr

X

No Chg

Synchronous Set/Reset X

SRVAL

Synchronous Set/Reset During Write RAM pdata

Data

SRVAL

Read RAM, no Write Operation X

X

RAM(pdata)

Write RAM, Simultaneous Read Operation pdata

Data

WRITE_MODE = WRITE_FIRST pdata

data

RAM(addr) ← pdata

RAM(addr) ← data

WRITE_MODE = READ_FIRST RAM(data)

RAM(data)

RAM(addr) ← pdata

RAM(addr) ← pdata

WRITE_MODE = NO_CHANGE No Chg

DS312 (v4.1) July 19, 2013 Product Specification

No Chg

RAM(addr) ← pdata

RAM(addr) ← pdata

www.xilinx.com 40

Spartan-3E FPGA Family: Functional Description There are a number of different conditions under which data can be accessed at the DO outputs. Basic data access always occurs when the WE input is inactive. Under this condition, data stored in the memory location addressed by the ADDR lines passes through a output latch to the DO outputs. The timing for basic data access is shown in the

portions of Figure 33, Figure 34, and Figure 35 during which WE is Low. Data also can be accessed on the DO outputs when asserting the WE input based on the value of the WRITE_MODE attribute as described in Table 26.

Table 26: WRITE_MODE Effect on Data Output Latches During Write Operations Write Mode

Effect on Opposite Port (dual-port only with same address)

Effect on Same Port

WRITE_FIRST Read After Write

Data on DI and DIP inputs is written into specified Invalidates data on DO and DOP outputs. RAM location and simultaneously appears on DO and DOP outputs.

READ_FIRST Read Before Write

Data from specified RAM location appears on DO and Data from specified RAM location appears on DO and DOP outputs. DOP outputs. Data on DI and DIP inputs is written into specified location.

NO_CHANGE No Read on Write

Data on DO and DOP outputs remains unchanged. Data on DI and DIP inputs is written into specified location.

Invalidates data on DO and DOP outputs.

X-Ref Target - Figure 33

Data_in

DI

Internal Memory

DO

Data_out = Data_in

CLK

WE DI

XXXX

ADDR DO

aa

0000

1111

2222

bb

cc

MEM(aa)

1111

XXXX

dd

2222

MEM(dd)

EN DISABLED

READ

WRITE MEM(bb)=1111

WRITE MEM(cc)=2222

READ DS312-2_05_020905

Figure 33: Waveforms of Block RAM Data Operations with WRITE_FIRST Selected Setting the WRITE_MODE attribute to a value of WRITE_FIRST, data is written to the addressed memory location on an enabled active CLK edge and is also passed to the DO outputs. WRITE_FIRST timing is shown in the portion of Figure 33 during which WE is High. Setting the WRITE_MODE attribute to a value of READ_FIRST, data already stored in the addressed location passes to the DO outputs before that location is overwritten with new data from the DI inputs on an enabled active CLK edge. READ_FIRST timing is shown in the portion of Figure 34 during which WE is High.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 41

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 34

Data_in

DI

Internal Memory

DO

Prior stored data

CLK

WE DI

XXXX

ADDR DO

aa

0000

1111

2222

bb

cc

MEM(aa)

old MEM(bb)

XXXX

dd

old MEM(cc)

MEM(dd)

EN DISABLED

READ

WRITE MEM(bb)=1111

WRITE MEM(cc)=2222

READ DS312-2_06_020905

Figure 34: Waveforms of Block RAM Data Operations with READ_FIRST Selected X-Ref Target - Figure 35

Data_in

DI

Internal Memory

DO

No change during write

CLK WE DI

XXXX

ADDR DO

aa

0000

1111

2222

bb

cc

MEM(aa)

XXXX

dd

MEM(dd)

EN DISABLED

READ

WRITE MEM(bb)=1111

WRITE MEM(cc)=2222

READ

DS312-2_07_020905

Figure 35: Waveforms of Block RAM Data Operations with NO_CHANGE Selected Setting the WRITE_MODE attribute to a value of NO_CHANGE, puts the DO outputs in a latched state when asserting WE. Under this condition, the DO outputs retain the data driven just before WE is asserted. NO_CHANGE timing is shown in the portion of Figure 35 during which WE is High.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 42

Spartan-3E FPGA Family: Functional Description

Dedicated Multipliers

product ranging from –17,179,738,11210 to +17,179,869,18410.

For additional information, refer to the “Using Embedded Multipliers” chapter in UG331.

Implement multipliers with inputs less than 18 bits by sign-extending the inputs (i.e., replicating the most-significant bit). Wider multiplication operations are performed by combining the dedicated multipliers and slice-based logic in any viable combination or by time-sharing a single multiplier. Perform unsigned multiplication by restricting the inputs to the positive range. Tie the most-significant bit Low and represent the unsigned value in the remaining 17 lesser-significant bits.

The Spartan-3E devices provide 4 to 36 dedicated multiplier blocks per device. The multipliers are located together with the block RAM in one or two columns depending on device density. See Arrangement of RAM Blocks on Die for details on the location of these blocks and their connectivity.

Operation The multiplier blocks primarily perform two’s complement numerical multiplication but can also perform some less obvious applications, such as simple data storage and barrel shifting. Logic slices also implement efficient small multipliers and thereby supplement the dedicated multipliers. The Spartan-3E dedicated multiplier blocks have additional features beyond those provided in Spartan-3 FPGAs.

Optional Pipeline Registers As shown in Figure 36, each multiplier block has optional registers on each of the multiplier inputs and the output. The registers are named AREG, BREG, and PREG and can be used in any combination. The clock input is common to all the registers within a block, but each register has an independent clock enable and synchronous reset controls making them ideal for storing data samples and coefficients. When used for pipelining, the registers boost the multiplier clock rate, beneficial for higher performance applications.

Each multiplier performs the principle operation P = A × B, where ‘A’ and ‘B’ are 18-bit words in two’s complement form, and ‘P’ is the full-precision 36-bit product, also in two’s complement form. The 18-bit inputs represent values ranging from –131,07210 to +131,07110 with a resulting

Figure 36 illustrates the principle features of the multiplier block.

X-Ref Target - Figure 36

AREG (Optional) CEA A[17:0]

CE D

Q PREG (Optional)

RST CEP

X

RSTA

D

BREG (Optional) CEB B[17:0]

CE Q

P[35:0]

RST

CE D

RSTP

Q

RST RSTB DS312-2_27_021205

CLK

Figure 36: Principle Ports and Functions of Dedicated Multiplier Blocks Use the MULT18X18SIO primitive shown in Figure 37 to instantiate a multiplier within a design. Although high-level logic synthesis software usually automatically infers a multiplier, adding the pipeline registers might require the MULT18X18SIO primitive. Connect the appropriate signals to the MULT18X18SIO multiplier ports and set the individual AREG, BREG, and PREG attributes to ‘1’ to insert the DS312 (v4.1) July 19, 2013 Product Specification

associated register, or to 0 to remove it and make the signal path combinatorial.

www.xilinx.com 43

Spartan-3E FPGA Family: Functional Description

Cascading Multipliers

X-Ref Target - Figure 37

MULT18X18SIO A[17:0]

The MULT18X18SIO primitive has two additional ports called BCIN and BCOUT to cascade or share the multiplier’s ‘B’ input among several multiplier bocks. The 18-bit BCIN “cascade” input port offers an alternate input source from the more typical ‘B’ input. The B_INPUT attribute specifies whether the specific implementation uses the BCIN or ‘B’ input path. Setting B_INPUT to DIRECT chooses the ‘B’ input. Setting B_INPUT to CASCADE selects the alternate BCIN input. The BREG register then optionally holds the selected input value, if required.

P[35:0]

B[17:0] CEA CEB CEP CLK RSTA RSTB RSTP

BCOUT is an 18-bit output port that always reflects the value that is applied to the multiplier’s second input, which is either the ‘B’ input, the cascaded value from the BCIN input, or the output of the BREG if it is inserted.

BCOUT[17:0]

BCIN[17:0]

DS312-2_28_021205

Figure 37: MULT18X18SIO Primitive

Figure 38 illustrates the four possible configurations using different settings for the B_INPUT attribute and the BREG attribute. X-Ref Target - Figure 38

BCOUT[17:0]

BCOUT[17:0]

BREG CEB

X

CE D

X

Q BREG = 0 B_INPUT = CASCADE

CLK RST BREG = 1 B_INPUT = CASCADE

RSTB BCIN[17:0]

BCIN[17:0] BCOUT[17:0]

BCOUT[17:0] BREG CEB B[17:0]

X

X

CE D

B[17:0]

Q

BREG = 0 B_INPUT = DIRECT

CLK RST RSTB

BREG = 1 B_INPUT = DIRECT

DS312-2_29_021505

Figure 38: Four Configurations of the B Input

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 44

Spartan-3E FPGA Family: Functional Description The BCIN and BCOUT ports have associated dedicated routing that connects adjacent multipliers within the same column. Via the cascade connection, the BCOUT port of one multiplier block drives the BCIN port of the multiplier block directly above it. There is no connection to the BCIN port of the bottom-most multiplier block in a column or a connection from the BCOUT port of the top-most block in a column. As an example, Figure 39 shows the multiplier cascade capability within the XC3S100E FPGA, which has a single column of multiplier, four blocks tall. For clarity, the figure omits the register control inputs. X-Ref Target - Figure 39

BCOUT A P B B_INPUT = CASCADE

BCIN

BCOUT A P B B_INPUT = CASCADE

BCIN

BCOUT A P B B_INPUT = CASCADE

BCIN

BCOUT A P B B_INPUT = DIRECT

BCIN

DS312-2_30_021505

Figure 39: Multiplier Cascade Connection When using the BREG register, the cascade connection forms a shift register structure typically used in DSP algorithms such as direct-form FIR filters. When the BREG register is omitted, the cascade structure essentially feeds the same input value to more than one multiplier. This parallel connection serves to create wide-input multipliers, implement transpose FIR filters, and is used in any application that requires that several multipliers have the same input value.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 45

Spartan-3E FPGA Family: Functional Description

Multiplier/Block RAM Interaction Each multiplier is located adjacent to an 18 Kbit block RAM and shares some interconnect resources. Configuring an 18 Kbit block RAM for 36-bit wide data (512 x 36 mode) prevents use of the associated dedicated multiplier.

The upper 16 bits of the ‘A’ multiplicand input are shared with the upper 16 bits of the block RAM’s Port A Data input. Similarly, the upper 16 bits of the ‘B’ multiplicand input are shared with Port B’s data input. See also Figure 48, page 63. Table 27 defines each port of the MULT18X18SIO primitive.

Table 27: MULT18X18SIO Embedded Multiplier Primitives Description Signal Name

Direction

Function

A[17:0]

Input

The primary 18-bit two’s complement value for multiplication. The block multiplies by this value asynchronously if the optional AREG and PREG registers are omitted. When AREG and/or PREG are used, the value provided on this port is qualified by the rising edge of CLK, subject to the appropriate register controls.

B[17:0]

Input

The second 18-bit two’s complement value for multiplication if the B_INPUT attribute is set to DIRECT. The block multiplies by this value asynchronously if the optional BREG and PREG registers are omitted. When BREG and/or PREG are used, the value provided on this port is qualified by the rising edge of CLK, subject to the appropriate register controls.

BCIN[17:0]

Input

The second 18-bit two’s complement value for multiplication if the B_INPUT attribute is set to CASCADE. The block multiplies by this value asynchronously if the optional BREG and PREG registers are omitted. When BREG and/or PREG are used, the value provided on this port is qualified by the rising edge of CLK, subject to the appropriate register controls.

P[35:0]

Output

The 36-bit two’s complement product resulting from the multiplication of the two input values applied to the multiplier. If the optional AREG, BREG and PREG registers are omitted, the output operates asynchronously. Use of PREG causes this output to respond to the rising edge of CLK with the value qualified by CEP and RSTP. If PREG is omitted, but AREG and BREG are used, this output responds to the rising edge of CLK with the value qualified by CEA, RSTA, CEB, and RSTB. If PREG is omitted and only one of AREG or BREG is used, this output responds to both asynchronous and synchronous events.

BCOUT[17:0]

Output

The value being applied to the second input of the multiplier. When the optional BREG register is omitted, this output responds asynchronously in response to changes at the B[17:0] or BCIN[17:0] ports according to the setting of the B_INPUT attribute. If BREG is used, this output responds to the rising edge of CLK with the value qualified by CEB and RSTB.

CEA

Input

Clock enable qualifier for the optional AREG register. The value provided on the A[17:0] port is captured by AREG in response to a rising edge of CLK when this signal is High, provided that RSTA is Low.

RSTA

Input

Synchronous reset for the optional AREG register. AREG content is forced to the value zero in response to a rising edge of CLK when this signal is High.

CEB

Input

Clock enable qualifier for the optional BREG register. The value provided on the B[17:0] or BCIN[17:0] port is captured by BREG in response to a rising edge of CLK when this signal is High, provided that RSTB is Low.

RSTB

Input

Synchronous reset for the optional BREG register. BREG content is forced to the value zero in response to a rising edge of CLK when this signal is High.

CEP

Input

Clock enable qualifier for the optional PREG register. The value provided on the output of the multiplier port is captured by PREG in response to a rising edge of CLK when this signal is High, provided that RSTP is Low.

RSTP

Input

Synchronous reset for the optional PREG register. PREG content is forced to the value zero in response to a rising edge of CLK when this signal is High.

Notes: 1.

The control signals CLK, CEA, RSTA, CEB, RSTB, CEP, and RSTP have the option of inverted polarity.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 46

Spartan-3E FPGA Family: Functional Description

Digital Clock Managers (DCMs) For additional information, refer to the “Using Digital Clock Managers (DCMs)” chapter in UG331.

Differences from the Spartan-3 Architecture •

Spartan-3E FPGAs have two, four, or eight DCMs, depending on device size.



The variable phase shifting feature functions differently on Spartan-3E FPGAs than from Spartan-3 FPGAs.



The Spartan-3E DLLs support lower input frequencies, down to 5 MHz. Spartan-3 DLLs support down to 18 MHz.

surrounded by CLBs within the logic array and is no longer located at the top and bottom of a column of block RAM as in the Spartan-3 architecture. The Digital Clock Manager is instantiated within a design using a “DCM” primitive. The DCM supports three major functions: •

Clock-skew Elimination: Clock skew within a system occurs due to the different arrival times of a clock signal at different points on the die, typically caused by the clock signal distribution network. Clock skew increases setup and hold time requirements and increases clock-to-out times, all of which are undesirable in high frequency applications. The DCM eliminates clock skew by phase-aligning the output clock signal that it generates with the incoming clock signal. This mechanism effectively cancels out the clock distribution delays.



Frequency Synthesis: The DCM can generate a wide range of different output clock frequencies derived from the incoming clock signal. This is accomplished by either multiplying and/or dividing the frequency of the input clock signal by any of several different factors.



Phase Shifting: The DCM provides the ability to shift the phase of all its output clock signals with respect to the input clock signal.

Overview Spartan-3E FPGA Digital Clock Managers (DCMs) provide flexible, complete control over clock frequency, phase shift and skew. To accomplish this, the DCM employs a Delay-Locked Loop (DLL), a fully digital control system that uses feedback to maintain clock signal characteristics with a high degree of precision despite normal variations in operating temperature and voltage. This section provides a fundamental description of the DCM. The XC3S100E FPGA has two DCMs, one at the top and one at the bottom of the device. The XC3S250E and XC3S500E FPGAs each include four DCMs, two at the top and two at the bottom. The XC3S1200E and XC3S1600E FPGAs contain eight DCMs with two on each edge (see also Figure 45). The DCM in Spartan-3E FPGAs is

Although a single design primitive, the DCM consists of four interrelated functional units: the Delay-Locked Loop (DLL), the Digital Frequency Synthesizer (DFS), the Phase Shifter (PS), and the Status Logic. Each component has its associated signals, as shown in Figure 40.

X-Ref Target - Figure 40

DCM PSINCDEC PSEN PSCLK

Phase Shifter

Delay Steps

Input Stage

Output Stage

CLK0

CLKIN

CLKFB

PSDONE

CLK90 CLK180 CLK270 CLK2X CLK2X180 CLKDV CLKFX CLKFX180

DFS DLL RST

Status Logic

Clock Distribution Delay

8

LOCKED STATUS [7:0]

DS099-2_07_101205

Figure 40: DCM Functional Blocks and Associated Signals

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 47

Spartan-3E FPGA Family: Functional Description

Delay-Locked Loop (DLL) The most basic function of the DLL component is to eliminate clock skew. The main signal path of the DLL consists of an input stage, followed by a series of discrete delay elements or steps, which in turn leads to an output stage. This path together with logic for phase detection and control forms a system complete with feedback as shown in Figure 41. In Spartan-3E FPGAs, the DLL is implemented using a counter-based delay line.

The DLL component has two clock inputs, CLKIN and CLKFB, as well as seven clock outputs, CLK0, CLK90, CLK180, CLK270, CLK2X, CLK2X180, and CLKDV as described in Table 28. The clock outputs drive simultaneously. Signals that initialize and report the state of the DLL are discussed in Status Logic.

CLKIN

Delay 1

Delay 2

Delay n-1

Delay n

Output Section

X-Ref Target - Figure 41

Control

CLKFB

CLK0 CLK90 CLK180 CLK270 CLK2X CLK2X180 CLKDV

LOCKED

Phase Detection

RST

DS099-2_08_041103

Figure 41: Simplified Functional Diagram of DLL Table 28: DLL Signals Signal

Direction

Description

CLKIN

Input

Receives the incoming clock signal. See Table 30, Table 31, and Table 32 for optimal external inputs to a DCM.

CLKFB

Input

Accepts either CLK0 or CLK2X as the feedback signal. (Set the CLK_FEEDBACK attribute accordingly).

CLK0

Output

Generates a clock signal with the same frequency and phase as CLKIN.

CLK90

Output

Generates a clock signal with the same frequency as CLKIN, phase-shifted by 90°.

CLK180

Output

Generates a clock signal with the same frequency as CLKIN, phase-shifted by 180°.

CLK270

Output

Generates a clock signal with the same frequency as CLKIN, phase-shifted by 270°.

CLK2X

Output

Generates a clock signal with the same phase as CLKIN, and twice the frequency.

CLK2X180

Output

Generates a clock signal with twice the frequency of CLKIN, and phase-shifted 180° with respect to CLK2X.

CLKDV

Output

Divides the CLKIN frequency by CLKDV_DIVIDE value to generate lower frequency clock signal that is phase-aligned to CLKIN.

The clock signal supplied to the CLKIN input serves as a reference waveform. The DLL seeks to align the rising-edge of feedback signal at the CLKFB input with the rising-edge of CLKIN input. When eliminating clock skew, the common approach to using the DLL is as follows: The CLK0 signal is passed through the clock distribution network that feeds all the registers it synchronizes. These registers are either DS312 (v4.1) July 19, 2013 Product Specification

internal or external to the FPGA. After passing through the clock distribution network, the clock signal returns to the DLL via a feedback line called CLKFB. The control block inside the DLL measures the phase error between CLKFB and CLKIN. This phase error is a measure of the clock skew that the clock distribution network introduces. The control block activates the appropriate number of delay steps to

www.xilinx.com 48

Spartan-3E FPGA Family: Functional Description cancel out the clock skew. When the DLL phase-aligns the CLK0 signal with the CLKIN signal, it asserts the LOCKED output, indicating a lock on to the CLKIN signal.

DLL Attributes and Related Functions The DLL unit has a variety of associated attributes as described in Table 29. Each attribute is described in detail in the sections that follow.

Table 29: DLL Attributes Attribute

Description

Values

CLK_FEEDBACK

Chooses either the CLK0 or CLK2X output to drive the CLKFB input

NONE, 1X, 2X

CLKIN_DIVIDE_BY_2

Halves the frequency of the CLKIN signal just as it enters the DCM

FALSE, TRUE

CLKDV_DIVIDE

Selects the constant used to divide the CLKIN input 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6.0, 6.5, 7.0, frequency to generate the CLKDV output frequency 7.5, 8, 9, 10, 11, 12, 13, 14, 15, and 16

CLKIN_PERIOD

Additional information that allows the DLL to operate with the most efficient lock time and the best jitter tolerance

Floating-point value representing the CLKIN period in nanoseconds

DLL Clock Input Connections For best results, an external clock source enters the FPGA via a Global Clock Input (GCLK). Each specific DCM has four possible direct, optimal GCLK inputs that feed the DCM’s CLKIN input, as shown in Table 30. Table 30 also provides the specific pin numbers by package for each GCLK input. The two additional DCM’s on the XC3S1200E and XC3S1600E have similar optimal connections from the left-edge LHCLK and the right-edge RHCLK inputs, as described in Table 31 and Table 32. •

Design Note Avoid using global clock input GCLK1 as it is always shared with the M2 mode select pin. Global clock inputs GCLK0, GCLK2, GCLK3, GCLK12, GCLK13, GCLK14, and GCLK15 have shared functionality in some configuration modes.

The DCM supports differential clock inputs (for example, LVDS, LVPECL_25) via a pair of GCLK inputs that feed an internal single-ended signal to the DCM’s CLKIN input.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 49

Spartan-3E FPGA Family: Functional Description

Table 30: Direct Clock Input Connections and Optional External Feedback to Associated DCMs Differential Pair Package

N

P

Differential Pair N

Differential Pair

P

N

Pin Number for Single-Ended Input VQ100

P91

P90

P89

P

Differential Pair N

P

Pin Number for Single-Ended Input

P88

P86

P85

P84

P83

CP132

B7

A7

C8

B8

A9

B9

C9

A10

TQ144

P131

P130

P129

P128

P126

P125

P123

P122

PQ208

P186

P185

P184

P183

P181

P180

P178

P177

FT256

D8

C8

B8

A8

A9

A10

F9

E9

FG320

D9

C9

B9

B8

A10

B10

E10

D10

FG400

A9

A10

G10

H10

E10

E11

G11

F11

FG484

B11

C11

H11

H12

C12

B12

E12

F12

Top Left DCM XC3S100: N/A XC3S250E, XC3S500E: DCM_X0Y1 XC3S1200E, XC3S1600E: DCM_X1Y3

Associated Global Buffers BUFGMUX_X2Y11

 GCLK8

BUFGMUX_X2Y10

 GCLK9

BUFGMUX_X1Y11

 GCLK10

BUFGMUX_X1Y10

 GCLK11









H

G

F

E









GCLK7

GCLK6

GCLK5

GCLK4

Top Right DCM XC3S100: DCM_X0Y1 XC3S250E, XC3S500E: DCM_X1Y1 XC3S1200E, XC3S1600E: DCM_X2Y3

GCLK14

GCLK15









Differential Pair Package

P

N

A







 BUFGMUX_X2Y1

GCLK13

B BUFGMUX_X2Y0

GCLK12

C BUFGMUX_X1Y1

Bottom Left DCM XC3S100: N/A XC3S250E, XC3S500E: DCM_X0Y0 XC3S1200E, XC3S1600E: DCM_X1Y0

D BUFGMUX_X1Y0

Clock Line (see Table 41)

Associated Global Buffers

Differential Pair P

P32

P33

P35

GCLK0

GCLK1

GCLK2

GCLK3









Differential Pair

N

P

Pin Number for Single-Ended Input VQ100

Bottom Right DCM XC3S100: DCM_X0Y0 XC3S250E, XC3S500E: DCM_X1Y0 XC3S1200E, XC3S1600E: DCM_X2Y0

N

Differential Pair P

N

Pin Number for Single-Ended Input

P36

P38

P39

P40

P41

CP132

M4

N4

M5

N5

M6

N6

P6

P7

TQ144

P50

P51

P53

P54

P56

P57

P58

P59

PQ208

P74

P75

P77

P78

P80

P81

P82

P83

FT256

M8

L8

N8

P8

T9

R9

P9

N9

FG320

N9

M9

U9

V9

U10

T10

R10

P10

FG400

W9

W10

R10

P10

P11

P12

V10

V11

FG484

V11

U11

R11

T11

R12

P12

Y12

W12

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 50

Spartan-3E FPGA Family: Functional Description

Table 31: Direct Clock Input and Optional External Feedback to Left-Edge DCMs (XC3S1200E and XC3S1600E) CP132

TQ144

PQ208

FT256

FG320

Left Edge

FG400

FG484

LHCLK

P

P9

F3

P14

P22

H5

J5

K3

M5



LHCLK0

N

P10

F2

P15

P23

H6

J4

K2

L5



LHCLK1

P

P11

F1

P16

P24

H3

J1

K7

L8



LHCLK2

N

P12

G1

P17

P25

H4

J2

L7

M8



LHCLK3

P

P15

G3

P20

P28

J2

K3

M1

M1



LHCLK4

N

P16

H1

P21

P29

J3

K4

L1

N1



LHCLK5

P

P17

H2

P22

P30

J5

K6

M3

M3



LHCLK6

N

P18

H3

P23

P31

J4

K5

L3

M4



LHCLK7

DCM/BUFGMUX BUFGMUX_X0Y5



D

BUFGMUX_X0Y4



C Clock Lines

Single-Ended Pin Number by Package Type VQ100

DCM_X0Y2

BUFGMUX_X0Y3



B

BUFGMUX_X0Y2



A

BUFGMUX_X0Y9



H

BUFGMUX_X0Y8



G Clock Lines

Pair

Pair

Pair

Pair

Diff. Clock

DCM_X0Y1

BUFGMUX_X0Y7



F

BUFGMUX_X0Y6



E

Table 32: Direct Clock Input and Optional External Feedback to Right-Edge DCMs (XC3S1200E and XC3S1600E)



BUFGMUX_X3Y4

DCM_X3Y2



BUFGMUX_X3Y3

A



BUFGMUX_X3Y2

H



BUFGMUX_X3Y9

G



BUFGMUX_X3Y8

Clock Lines

B

DCM_X3Y1

F



BUFGMUX_X3Y7

E



BUFGMUX_X3Y6

TQ144

PQ208

FT256

FG320

FG484

Diff. Clock

RHCLK7



P68

G13

P94

P135

H11

J14

J20

L19

N

RHCLK6



P67

G14

P93

P134

H12

J15

K20

L18

P

RHCLK5



P66

H12

P92

P133

H14

J16

K14

L21

N

RHCLK4



P65

H13

P91

P132

H15

J17

K13

L20

P

RHCLK3



P63

J14

P88

P129

J13

K14

L14

M16

N

RHCLK2



P62

J13

P87

P128

J14

K15

L15

M15

P

RHCLK1



P61

J12

P86

P127

J16

K12

L16

M22

N

RHCLK0



P60

K14

P85

P126

K16

K13

M16

N22

P

Every FPGA input provides a possible DCM clock input, but the path is not temperature and voltage compensated like the GCLKs. Alternatively, clock signals within the FPGA optionally provide a DCM clock input via a Global Clock Multiplexer Buffer (BUFGMUX). The global clock net DS312 (v4.1) July 19, 2013 Product Specification

FG400

Pair

C

CP132

Pair

BUFGMUX_X3Y5

VQ100

Pair



Clock Lines

D

Single-Ended Pin Number by Package Type RHCLK

Pair

Right Edge DCM/BUFGMUX

connects directly to the CLKIN input. The internal and external connections are shown in Figure 42a and Figure 42c, respectively.

www.xilinx.com 51

Spartan-3E FPGA Family: Functional Description

DLL Clock Output and Feedback Connections As many as four of the nine DCM clock outputs can simultaneously drive four of the BUFGMUX buffers on the same die edge. All DCM clock outputs can simultaneously drive general routing resources, including interconnect leading to OBUF buffers. The feedback loop is essential for DLL operation. Either the CLK0 or CLK2X outputs feed back to the CLKFB input via a BUFGMUX global buffer to eliminate the clock distribution delay. The specific BUFGMUX buffer used to feed back the CLK0 or CLK2X signal is ideally one of the BUFGMUX buffers associated with a specific DCM, as shown in Table 30, Table 31, and Table 32. The feedback path also phase-aligns the other seven DLL outputs: CLK0, CLK90, CLK180, CLK270, CLKDV, CLK2X, or CLK2X180. The CLK_FEEDBACK attribute value must agree with the physical feedback connection. Use “1X” for CLK0 feedback and “2X” for CLK2X feedback. If the DFS unit is used stand-alone, without the DLL, then no feedback is required and set the CLK_FEEDBACK attribute to “NONE”.

Two basic cases determine how to connect the DLL clock outputs and feedback connections: on-chip synchronization and off-chip synchronization, which are illustrated in Figure 42a through Figure 42d. In the on-chip synchronization case in Figure 42a and Figure 42b, it is possible to connect any of the DLL’s seven output clock signals through general routing resources to the FPGA’s internal registers. Either a Global Clock Buffer (BUFG) or a BUFGMUX affords access to the global clock network. As shown in Figure 42a, the feedback loop is created by routing CLK0 (or CLK2X) in Figure 42b to a global clock net, which in turn drives the CLKFB input. In the off-chip synchronization case in Figure 42c and Figure 42d, CLK0 (or CLK2X) plus any of the DLL’s other output clock signals exit the FPGA using output buffers (OBUF) to drive an external clock network plus registers on the board. As shown in Figure 42c, the feedback loop is formed by feeding CLK0 (or CLK2X) in Figure 42d back into the FPGA, then to the DCM’s CLKFB input via a Global Buffer Input, specified in Table 30.

X-Ref Target - Figure 42

FPGA

FPGA BUFGMUX

BUFGMUX BUFG CLKIN

DCM

CLK90 CLK180 CLK270 CLKDV CLK2X CLK2X180

CLKFB

BUFG CLKIN

DCM

Clock Net Delay

CLK0 CLK90 CLK180 CLK270 CLKDV CLK2X180 CLK2X

CLKFB

CLK0

BUFGMUX

BUFGMUX CLK2X

CLK0

(a) On-Chip with CLK0 Feedback

(b) On-Chip with CLK2X Feedback

FPGA IBUFG CLKIN

DCM CLKFB

Clock Net Delay

FPGA

CLK90 CLK180 CLK270 CLKDV CLK2X CLK2X180

OBUF

IBUFG CLKIN Clock Net Delay

DCM CLKFB

CLK0 OBUF

IBUFG

CLK0 CLK90 CLK180 CLK270 CLKDV CLK2X180

OBUF

Clock Net Delay

CLK2X

IBUFG

OBUF

CLK2X

CLK0

(c) Off-Chip with CLK0 Feedback

(d) Off-Chip with CLK2X Feedback DS099-2_09_082104

Figure 42: Input Clock, Output Clock, and Feedback Connections for the DLL

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 52

Spartan-3E FPGA Family: Functional Description

Accommodating Input Frequencies Beyond Specified Maximums If the CLKIN input frequency exceeds the maximum permitted, divide it down to an acceptable value using the CLKIN_DIVIDE_BY_2 attribute. When this attribute is set to “TRUE”, the CLKIN frequency is divided by a factor of two as it enters the DCM. In addition, the CLKIN_DIVIDE_BY_2 option produces a 50% duty-cycle on the input clock, although at half the CLKIN frequency.

multiple (for multiplication) of the incoming clock frequency. The CLK2X output produces an in-phase signal that is twice the frequency of CLKIN. The CLK2X180 output also doubles the frequency, but is 180° out-of-phase with respect to CLKIN. The CLKDIV output generates a clock frequency that is a predetermined fraction of the CLKIN frequency. The CLKDV_DIVIDE attribute determines the factor used to divide the CLKIN frequency. The attribute can be set to various values as described in Table 29. The basic frequency synthesis outputs are described in Table 28.

Quadrant and Half-Period Phase Shift Outputs

Duty Cycle Correction of DLL Clock Outputs

In addition to CLK0 for zero-phase alignment to the CLKIN signal, the DLL also provides the CLK90, CLK180, and CLK270 outputs for 90°, 180°, and 270° phase-shifted signals, respectively. These signals are described in Table 28, page 48 and their relative timing is shown in Figure 43. For control in finer increments than 90°, see Phase Shifter (PS).

The DLL output signals exhibit a 50% duty cycle, even if the incoming CLKIN signal has a different duty cycle. Fifty-percent duty cycle means that the High and Low times of each clock cycle are equal.

X-Ref Target - Figure 43

Phase:

0

o

o

o

90 180 270

o

0

o

o

o

90 180 270

o

0

o

Input Signal (40%/60% Duty Cycle)

DLL Performance Differences Between Steppings As indicated in Digital Clock Manager (DCM) Timing (Module 3), the Stepping 1 revision silicon supports higher maximum input and output frequencies. Stepping 1 devices are backwards compatible with Stepping 0 devices.

Digital Frequency Synthesizer (DFS)

t

The DFS unit generates clock signals where the output frequency is a product of the CLKIN input clock frequency and a ratio of two user-specified integers. The two dedicated outputs from the DFS unit, CLKFX and CLKFX180, are defined in Table 33.

CLKIN

Output Signal - Duty Cycle Corrected

Table 33: DFS Signals

CLK0

Signal CLK90

Direction

CLKFX

Output

Multiplies the CLKIN frequency by the attribute-value ratio (CLKFX_MULTIPLY/ CLKFX_DIVIDE) to generate a clock signal with a new target frequency.

CLKFX180

Output

Generates a clock signal with the same frequency as CLKFX, but shifted 180° out-of-phase.

CLK180

CLK270

CLK2X

CLK2X180

CLKDV DS099-2_10_101105

Figure 43: Characteristics of the DLL Clock Outputs

Basic Frequency Synthesis Outputs The DLL component provides basic options for frequency multiplication and division in addition to the more flexible synthesis capability of the DFS component, described in a later section. These operations result in output clock signals with frequencies that are either a fraction (for division) or a DS312 (v4.1) July 19, 2013 Product Specification

Description

The signal at the CLKFX180 output is essentially an inversion of the CLKFX signal. These two outputs always exhibit a 50% duty cycle, even when the CLKIN signal does not. The DFS clock outputs are active coincident with the seven DLL outputs and their output phase is controlled by the Phase Shifter unit (PS). The output frequency (fCLKFX) of the DFS is a function of the incoming clock frequency (fCLKIN) and two integer attributes, as follows. CLKFX_MULTIPLY Eq 1 f CLKFX = f CLKIN •  ----------------------------------------------------  CLKFX_DIVIDE  The CLKFX_MULTIPLY attribute is an integer ranging from 2 to 32, inclusive, and forms the numerator in Equation 1.

www.xilinx.com 53

Spartan-3E FPGA Family: Functional Description The CLKFX_DIVIDE is an integer ranging from 1 to 32, inclusive and forms the denominator in Equation 1. For example, if CLKFX_MULTIPLY = 5 and CLKFX_DIVIDE = 3, the frequency of the output clock signal is 5/3 that of the input clock signal. These attributes and their acceptable ranges are described in Table 34.

periods, which is equivalent in time to five CLKFX output periods.

Description

Values

CLKFX_MULTIPLY

Frequency multiplier constant

Integer from 2 to 32, inclusive

Smaller CLKFX_MULTIPLY and CLKFX_DIVIDE values result in faster lock times. Therefore, CLKFX_MULTIPLY and CLKFX_DIVIDE must be factored to reduce their values wherever possible. For example, given CLKFX_MULTIPLY = 9 and CLKFX_DIVIDE = 6, removing a factor of three yields CLKFX_MULTIPLY = 3 and CLKFX_DIVIDE = 2. While both value-pairs result in the multiplication of clock frequency by 3/2, the latter value-pair enables the DLL to lock more quickly.

CLKFX_DIVIDE

Frequency divisor constant

Integer from 1 to 32, inclusive

Phase Shifter (PS)

Table 34: DFS Attributes Attribute

Any combination of integer values can be assigned to the CLKFX_MULTIPLY and CLKFX_DIVIDE attributes, provided that two conditions are met: 1. The two values fall within their corresponding ranges, as specified in Table 34. 2. The fCLKFX output frequency calculated in Equation 1 falls within the DCM’s operating frequency specifications (see Table 107 in Module 3).

DFS With or Without the DLL Although the CLKIN input is shared with both units, the DFS unit functions with or separately from the DLL unit. Separate from the DLL, the DFS generates an output frequency from the CLKIN frequency according to the respective CLKFX_MULTIPLY and CLKFX_DIVIDE values. Frequency synthesis does not require a feedback loop. Furthermore, without the DLL, the DFS unit supports a broader operating frequency range. With the DLL, the DFS unit operates as described above, only with the additional benefit of eliminating the clock distribution delay. In this case, a feedback loop from the CLK0 or CLK2X output to the CLKFB input must be present. When operating with the DLL unit, the DFS’s CLKFX and CLKFX180 outputs are phase-aligned with the CLKIN input every CLKFX_DIVIDE cycles of CLKIN and every CLKFX_MULTIPLY cycles of CLKFX. For example, when CLKFX_MULTIPLY = 5 and CLKFX_DIVIDE = 3, the input and output clock edges coincide every three CLKIN input

The DCM provides two approaches to controlling the phase of a DCM clock output signal relative to the CLKIN signal: First, eight of the nine DCM clock outputs – CLK0, CLK90, CLK180, CLK270, CLK2X, CLK2X180, CLKFX, and CLKFX180 – provide either quadrant or half-period phase shifting of the input clock. Second, the PS unit provides additional fine phase shift control of all nine DCM outputs. The PS unit accomplishes this by introducing a “fine phase shift” delay (TPS) between the CLKFB and CLKIN signals inside the DLL unit. In FIXED phase shift mode, the fine phase shift is specified at design time with a resolution down to 1/256th of a CLKIN cycle or one delay step (DCM_DELAY_STEP), whichever is greater. This fine phase shift value is relative to the coarser quadrant or half-period phase shift of the DCM clock output. When used, the PS unit shifts the phase of all nine DCM clock output signals.

Enabling Phase Shifting and Selecting an Operating Mode The CLKOUT_PHASE_SHIFT attribute controls the PS unit for the specific DCM instantiation. As described in Table 35, this attribute has three possible values: NONE, FIXED, and VARIABLE. When CLKOUT_PHASE_SHIFT = NONE, the PS unit is disabled and the DCM output clocks are phase-aligned to the CLKIN input via the CLKFB feedback path. Figure 44a shows this case. The PS unit is enabled when the CLKOUT_PHASE_SHIFT attribute is set to FIXED or VARIABLE modes. These two modes are described in the sections that follow.

Table 35: PS Attributes Attribute

Description

Values

CLKOUT_PHASE_SHIFT

Disables the PS component or chooses between Fixed Phase and Variable Phase modes.

NONE, FIXED, VARIABLE

PHASE_SHIFT

Determines size and direction of initial fine phase shift.

Integers from –255 to +255

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 54

Spartan-3E FPGA Family: Functional Description

FIXED Phase Shift Mode The FIXED phase shift mode shifts the DCM outputs by a fixed amount (TPS), controlled by the user-specified PHASE_SHIFT attribute. The PHASE_SHIFT value (shown as P in Figure 44) must be an integer ranging from –255 to +255. PHASE_SHIFT specifies a phase shift delay as a fraction of the TCLKIN. The phase shift behavior is different between ISE 8.1, Service Pack 3 and prior software versions, as described below. Design Note Prior to ISE 8.1i, Service Pack 3, the FIXED phase shift feature operated differently than the Spartan-3 DCM design primitive and simulation model. Designs using software prior to ISE 8.1i, Service Pack 3 require recompilation using the latest ISE software release. The following Answer Record contains additional information: http://www.xilinx.com/support/answers/23153.htm. FIXED Phase Shift using ISE 8.1i, Service Pack 3 and later: See Equation 2. The value corresponds to a phase shift range of –360° to +360°, which matches behavior of the Spartan-3 DCM design primitive and simulation model. PHASESHIFT t PS =  ---------------------------------------- • T CLKIN   256

FIXED Phase Shift prior to ISE 8.1i, Service Pack 3: See Equation 3. The value corresponds to a phase shift range of –180° to +180° degrees, which is different from the Spartan-3 DCM design primitive and simulation model. Designs created prior to ISE 8.1i, Service Pack 3 must be recompiled using the most recent ISE development software. PHASESHIFT Eq 3 t PS =  ---------------------------------------- • T CLKIN   512 When the PHASE_SHIFT value is zero, CLKFB and CLKIN are in phase, the same as when the PS unit is disabled. When the PHASE_SHIFT value is positive, the DCM outputs are shifted later in time with respect to CLKIN input. When the attribute value is negative, the DCM outputs are shifted earlier in time with respect to CLKIN. Figure 44b illustrates the relationship between CLKFB and CLKIN in the Fixed Phase mode. In the Fixed Phase mode, the PSEN, PSCLK, and PSINCDEC inputs are not used and must be tied to GND. Equation 2 or Equation 3 applies only to FIXED phase shift mode. The VARIABLE phase shift mode operates differently.

Eq 2

X-Ref Target - Figure 44

a. CLKOUT_PHASE_SHIFT = NONE CLKIN

CLKFB (via CLK0 or CLK2X feedback)

b. CLKOUT_PHASE_SHIFT = FIXED CLKIN Shift Range over all P Values:

–255

0

+255 P * TCLKIN 256

CLKFB (via CLK0 or CLK2X feedback)

DS312-2_61_021606

Figure 44: NONE and FIXED Phase Shifter Waveforms (ISE 8.1i, Service Pack 3 and later)

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 55

Spartan-3E FPGA Family: Functional Description

VARIABLE Phase Shift Mode In VARIABLE phase shift mode, the FPGA application dynamically adjusts the fine phase shift value using three

inputs to the PS unit (PSEN, PSCLK, and PSINCDEC), as defined in Table 36 and shown in Figure 40.

Table 36: Signals for Variable Phase Mode Signal

Direction

Description

PSEN(1)

Input

Enables the Phase Shift unit for variable phase adjustment.

PSCLK(1)

Input

Clock to synchronize phase shift adjustment.

PSINCDEC(1)

Input

When High, increments the current phase shift value. When Low, decrements the current phase shift value. This signal is synchronized to the PSCLK signal.

PSDONE

Output

Goes High to indicate that the present phase adjustment is complete and PS unit is ready for next phase adjustment request. This signal is synchronized to the PSCLK signal.

Notes: 1.

This input supports either a true or inverted polarity.

The FPGA application uses the three PS inputs on the Phase Shift unit to dynamically and incrementally increase or decrease the phase shift amount on all nine DCM clock outputs.

phase shift range measured in time and not steps, use MAX_STEPS derived in Equation 6 and Equation 7 for VALUE in Equation 4 and Equation 5.

To adjust the current phase shift value, the PSEN enable signal must be High to enable the PS unit. Coincidently, PSINCDEC must be High to increment the current phase shift amount or Low to decrement the current amount. All VARIABLE phase shift operations are controlled by the PSCLK input, which can be the CLKIN signal or any other clock signal.

MAX_STEPS = ± [ INTEGER ( 10 • ( T CLKIN – 3 ) ) ]

Design Note The VARIABLE phase shift feature operates differently from the Spartan-3 DCM; use the DCM_SP primitive, not the DCM primitive.

If CLKIN < 60 MHz: Eq 6

If CLKIN ≥ 60 MHz: MAX_STEPS = ± [ INTEGER ( 15 • ( T CLKIN – 3 ) ) ]

Eq 7

The phase adjustment might require as many as 100 CLKIN cycles plus 3 PSCLK cycles to take effect, at which point the DCM’s PSDONE output goes High for one PSCLK cycle. This pulse indicates that the PS unit completed the previous adjustment and is now ready for the next request. Asserting the Reset (RST) input returns the phase shift to zero.

DCM_DELAY_STEP DCM_DELAY_STEP is the finest delay resolution available in the PS unit. Its value is provided at the bottom of Table 105 in Module 3. For each enabled PSCLK cycle that PSINCDEC is High, the PS unit adds one DCM_ DELAY_STEP of phase shift to all nine DCM outputs. Similarly, for each enabled PSCLK cycle that PSINCDEC is Low, the PS unit subtracts one DCM_ DELAY_STEP of phase shift from all nine DCM outputs. Because each DCM_DELAY_STEP has a minimum and maximum value, the actual phase shift delay for the present phase increment/decrement value (VALUE) falls within the minimum and maximum values according to Equation 4 and Equation 5. T PS ( Max ) = VALUE • DCM_DELAY_STEP_MAX Eq 4 T PS ( Min ) = VALUE • DCM_DELAY_STEP_MIN

Eq 5

The maximum variable phase shift steps, MAX_STEPS, is described in Equation 6 or Equation 7, for a given CLKIN input period, TCLKIN, in nanoseconds. To convert this to a

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 56

Spartan-3E FPGA Family: Functional Description

Status Logic The Status Logic indicates the present state of the DCM and a means to reset the DCM to its initial known state. The Status Logic signals are described in Table 37. In general, the Reset (RST) input is only asserted upon configuring the FPGA or when changing the CLKIN

frequency. The RST signal must be asserted for three or more CLKIN cycles. A DCM reset does not affect attribute values (for example, CLKFX_MULTIPLY and CLKFX_DIVIDE). If not used, RST is tied to GND. The eight bits of the STATUS bus are described in Table 38.

Table 37: Status Logic Signals Signal

Direction

Description

RST

Input

A High resets the entire DCM to its initial power-on state. Initializes the DLL taps for a delay of zero. Sets the LOCKED output Low. This input is asynchronous.

STATUS[7:0]

Output

The bit values on the STATUS bus provide information regarding the state of DLL and PS operation

LOCKED

Output

Indicates that the CLKIN and CLKFB signals are in phase by going High. The two signals are out-of-phase when Low.

Table 38: DCM Status Bus Bit

Name

Description

0

Reserved

-

1

CLKIN Stopped

When High, indicates that the CLKIN input signal is not toggling. When Low, indicates CLKIN is toggling. This bit functions only when the CLKFB input is connected.(1)

2

CLKFX Stopped

When High, indicates that the CLKFX output is not toggling. When Low, indicates the CLKFX output is toggling. This bit functions only when the CLKFX or CLKFX180 output are connected.

Reserved

-

3-6 Notes: 1.

When only the DFS clock outputs but none of the DLL clock outputs are used, this bit does not go High when the CLKIN signal stops.

Stabilizing DCM Clocks Before User Mode

Spread Spectrum

The STARTUP_WAIT attribute shown in Table 39 optionally delays the end of the FPGA’s configuration process until after the DCM locks to its incoming clock frequency. This option ensures that the FPGA remains in the Startup phase of configuration until all clock outputs generated by the DCM are stable. When all DCMs that have their STARTUP_WAIT attribute set to TRUE assert the LOCKED signal, then the FPGA completes its configuration process and proceeds to user mode. The associated bitstream generator (BitGen) option LCK_cycle specifies one of the six cycles in the Startup phase. The selected cycle defines the point at which configuration stalls until all the LOCKED outputs go High. See Start-Up, page 106 for more information.

DCMs accept typical spread spectrum clocks as long as they meet the input requirements. The DLL will track the frequency changes created by the spread spectrum clock to drive the global clocks to the FPGA logic. See XAPP469, Spread-Spectrum Clocking Reception for Displays for details.

Table 39: STARTUP_WAIT Attribute Attribute STARTUP_WAIT

Description When TRUE, delays transition from configuration to user mode until DCM locks to the input clock.

DS312 (v4.1) July 19, 2013 Product Specification

Values TRUE, FALSE

www.xilinx.com 57

Spartan-3E FPGA Family: Functional Description

Clocking Infrastructure For additional information, refer to the “Using Global Clock Resources” chapter in UG331. The Spartan-3E clocking infrastructure, shown in Figure 45, provides a series of low-capacitance, low-skew interconnect lines well-suited to carrying high-frequency signals throughout the FPGA. The infrastructure also includes the clock inputs and BUFGMUX clock buffers/multiplexers. The Xilinx Place-and-Route (PAR) software automatically routes high-fanout clock signals using these resources.

High or Low time of either input clock. The two clock inputs can be asynchronous with regard to each other, and the S input can change at any time, except for a short setup time prior to the rising edge of the presently selected clock (I0 or I1). This setup time is specified as TGSI in Table 101, page 137. Violating this setup time requirement possibly results in an undefined runt pulse output. Table 40: BUFGMUX Select Mechanism

Clock Inputs Clock pins accept external clock signals and connect directly to DCMs and BUFGMUX elements. Each Spartan-3E FPGA has: •

16 Global Clock inputs (GCLK0 through GCLK15) located along the top and bottom edges of the FPGA



8 Right-Half Clock inputs (RHCLK0 through RHCLK7) located along the right edge



8 Left-Half Clock inputs (LHCLK0 through LHCLK7) located along the left edge

Clock inputs optionally connect directly to DCMs using dedicated connections. Table 30, Table 31, and Table 32 show the clock inputs that best feed a specific DCM within a given Spartan-3E part number. Different Spartan-3E FPGA densities have different numbers of DCMs. The XC3S1200E and XC3S1600E are the only two densities with the left- and right-edge DCMs. Each clock input is also optionally a user-I/O pin and connects to internal interconnect. Some clock pad pins are input-only pins as indicated in Module 4, Pinout Descriptions. Design Note Avoid using global clock input GCLK1 as it is always shared with the M2 mode select pin. Global clock inputs GCLK0, GCLK2, GCLK3, GCLK12, GCLK13, GCLK14, and GCLK15 have shared functionality in some configuration modes.

S Input

O Output

0

I0 Input

1

I1 Input

The BUFG clock buffer primitive drives a single clock signal onto the clock network and is essentially the same element as a BUFGMUX, just without the clock select mechanism. Similarly, the BUFGCE primitive creates an enabled clock buffer using the BUFGMUX select mechanism. The I0 and I1 inputs to an BUFGMUX element originate from clock input pins, DCMs, or Double-Line interconnect, as shown in Figure 46. As shown in Figure 45, there are 24 BUFGMUX elements distributed around the four edges of the device. Clock signals from the four BUFGMUX elements at the top edge and the four at the bottom edge are truly global and connect to all clocking quadrants. The eight left-edge BUFGMUX elements only connect to the two clock quadrants in the left half of the device. Similarly, the eight right-edge BUFGMUX elements only connect to the right half of the device. BUFGMUX elements are organized in pairs and share I0 and I1 connections with adjacent BUFGMUX elements from a common clock switch matrix as shown in Figure 46. For example, the input on I0 of one BUFGMUX is also a shared input to I1 of the adjacent BUFGMUX. The clock switch matrix for the left- and right-edge BUFGMUX elements receive signals from any of the three following sources: an LHCLK or RHCLK pin as appropriate, a Double-Line interconnect, or a DCM in the XC3S1200E and XC3S1600E devices.

Clock Buffers/Multiplexers Clock Buffers/Multiplexers either drive clock input signals directly onto a clock line (BUFG) or optionally provide a multiplexer to switch between two unrelated, possibly asynchronous clock signals (BUFGMUX). Each BUFGMUX element, shown in Figure 46, is a 2-to-1 multiplexer. The select line, S, chooses which of the two inputs, I0 or I1, drives the BUFGMUX’s output signal, O, as described in Table 40. The switching from one clock to the other is glitch-less, and done in such a way that the output High and Low times are never shorter than the shortest DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 58

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 45

Global Clock Inputs GCLK11 GCLK10

4

GCLK7

BUFGMUX pair

4

4 H

G

8

F

8



2

H

Top Right Quadrant (TR)

8

8

DCM

Clock Line in Quadrant

XC3S100E (X0Y1) XC3S250E (X1Y1) XC3S500E (X1Y1) XC3S1200E (X2Y3) XC3S1600E (X2Y3)

4



XC3S1200E (X0Y1) XC3S1600E (X0Y1)

E

G



Top Spine

X0Y9 X0Y8

G

X2Y10 X2Y11

X1Y10 X1Y11

DCM 8



XC3S1200E (X3Y1) XC3S1600E (X3Y1)

2

8

DCM

Note 4







XC3S1200E (X0Y2) XC3S1600E (X0Y2)

Note 4

Note 3

8

2

8

Spine

Bottom Spine

X0Y6 X0Y7 X0Y5 X0Y4

Horizontal

8

Right Spine

D

C

2

8 8



DCM 2

4

8

DCM

4

D

XC3S250E (X0Y0) XC3S500E (X0Y0) XC3S1200E (X1Y0) XC3S1600E (X1Y0)

8

C

B

X1Y0 X1Y1

4

A

X2Y0 X2Y1

4 4

GCLK3 GCLK2

2 B Bottom Right Quadrant (BR)

A

X3Y2

Bottom Left Quadrant (BL)



RHCLK5 RHCLK4



B

X3Y3

X0Y2 X0Y3

2 XC3S1200E (X3Y2) XC3S1600E (X3Y2)

2 2

A

E

Right-Half Clock Inputs

C

8

X3Y5 X3Y4

D

Note 3

X3Y6

8

Left Spine



X3Y7

E



F

RHCLK1 RHCLK0 RHCLK7 RHCLK6

2 F

2

LHCLK0 LHCLK1

2

2 8

RHCLK3 RHCLK2

LHCLK6 LHCLK7

4

DCM

Top Left Quadrant (TL)

2

Left-Half Clock Inputs

GCLK5 GCLK4

X3Y9 X3Y8

H

2

LHCLK2 LHCLK3 LHCLK4 LHCLK5

GCLK6

DCM XC3S250E (X0Y1) XC3S500E (X0Y1) XC3S1200E (X1Y3) XC3S1600E (X1Y3)

BUFGMUX

2

GCLK9 GCLK8

DCM XC3S100E (X0Y0) XC3S250E (X1Y0) XC3S500E (X1Y0) XC3S1200E (X2Y0) XC3S1600E (X2Y0)

GCLK1 GCLK0

GCLK15 GCLK14

GCLK13 GCLK12

Global Clock Inputs

DS312-2_04_041106

Notes: 1. The diagram presents electrical connectivity. The diagram locations do not necessarily match the physical location on the device, although the coordinate locations shown are correct. 2. Number of DCMs and locations of these DCM varies for different device densities. The left and right DCMs are only in the XC3S1200E and XC3S1600E. The XC3S100E has only two DCMs, one on the top right and one on the bottom right of the die. 3. See Figure 47a, which shows how the eight clock lines are multiplexed on the left-hand side of the device. 4. See Figure 47b, which shows how the eight clock lines are multiplexed on the right-hand side of the device. 5. For best direct clock inputs to a particular clock buffer, not a DCM, see Table 41. 6. For best direct clock inputs to a particular DCM, not a BUFGMUX, see Table 30, Table 31, and Table 32. Direct pin inputs to a DCM are shown in gray.

Figure 45: Spartan-3E Internal Quadrant-Based Clock Network (Electrical Connectivity View)

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 59

Spartan-3E FPGA Family: Functional Description By contrast, the clock switch matrixes on the top and bottom edges receive signals from any of the five following sources: two GCLK pins, two DCM outputs, or one Double-Line interconnect. Table 41 indicates permissible connections between clock inputs and BUFGMUX elements. The I0-input provides the best input path to a clock buffer. The I1-input provides the secondary input for the clock multiplexer function.

The four BUFGMUX elements on the top edge are paired together and share inputs from the eight global clock inputs along the top edge. Each BUFGMUX pair connects to four of the eight global clock inputs, as shown in Figure 45. This optionally allows differential inputs to the global clock inputs without wasting a BUFGMUX element.

Table 41: Connections from Clock Inputs to BUFGMUX Elements and Associated Quadrant Clock Quadran t Clock Line(1)

Left-Half BUFGMUX Location(2)

I0 Input

I1 Input

Top or Bottom BUFGMUX Location(2)

I0 Input

I1 Input

Right-Half BUFGMUX Location(2)

I0 Input

I1 Input

H

X0Y9

LHCLK7

LHCLK6

X1Y10

GCLK7 or GCLK11

GCLK6 or GCLK10

X3Y9

RHCLK3

RHCLK2

G

X0Y8

LHCLK6

LHCLK7

X1Y11

GCLK6 or GCLK10

GCLK7 or GCLK11

X3Y8

RHCLK2

RHCLK3

F

X0Y7

LHCLK5

LHCLK4

X2Y10

GCLK5 or GCLK9

GCLK4 or GCLK8

X3Y7

RHCLK1

RHCLK0

E

X0Y6

LHCLK4

LHCLK5

X2Y11

GCLK4 or GCLK8

GCLK5 or GCLK9

X3Y6

RHCLK0

RHCLK1

D

X0Y5

LHCLK3

LHCLK2

X1Y0

GCLK3 or GCLK15

GCLK2 or GCLK14

X3Y5

RHCLK7

RHCLK6

C

X0Y4

LHCLK2

LHCLK3

X1Y1

GCLK2 or GCLK14

GCLK3 or GCLK15

X3Y4

RHCLK6

RHCLK7

B

X0Y3

LHCLK1

LHCLK0

X2Y0

GCLK1 or GCLK13

GCLK0 or GCLK12

X3Y3

RHCLK5

RHCLK4

A

X0Y2

LHCLK0

LHCLK1

X2Y1

GCLK0 or GCLK12

GCLK1 or GCLK13

X3Y2

RHCLK4

RHCLK5

Notes: 1. 2.

See Quadrant Clock Routing for connectivity details for the eight quadrant clocks. See Figure 45 for specific BUFGMUX locations, and Figure 47 for information on how BUFGMUX elements drive onto a specific clock line within a quadrant.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 60

Spartan-3E FPGA Family: Functional Description The connections for the bottom-edge BUFGMUX elements are similar to the top-edge connections (see Figure 46).

On the left and right edges, only two clock inputs feed each pair of BUFGMUX elements.

X-Ref Target - Figure 46

Left-/Right-Half BUFGMUX

Top/Bottom (Global) BUFGMUX

CLK Switch Matrix

CLK Switch Matrix BUFGMUX S I0 I1 I0 I1

BUFGMUX S I0

0 O 1

I1 I0

0 O 1

I1

S

0 O 1 0 O 1

S

LHCLK or RHCLK input

1st GCLK pin

Double Line

1st DCM output Double Line

DCM output*

2nd DCM output

*(XC3S1200E and XC3S1600E only)

2nd GCLK pin DS312-2_16_110706

Figure 46: Clock Switch Matrix to BUFGMUX Pair Connectivity

Quadrant Clock Routing

Table 42: QFP Package Clock Quadrant Locations

The clock routing within the FPGA is quadrant-based, as shown in Figure 45. Each clock quadrant supports eight total clock signals, labeled ‘A’ through ‘H’ in Table 41 and Figure 47. The clock source for an individual clock line originates either from a global BUFGMUX element along the top and bottom edges or from a BUFGMUX element along the associated edge, as shown in Figure 47. The clock lines feed the synchronous resource elements (CLBs, IOBs, block RAM, multipliers, and DCMs) within the quadrant. The four quadrants of the device are:

Clock Pins

Quadrant

GCLK[3:0]

BR

GCLK[7:4]

TR

GCLK[11:8]

TL

GCLK[15:12]

BL

RHCLK[3:0]

BR

RHCLK[7:4]

TR

LHCLK[3:0]

TL

LHCLK[7:4]

BL



Top Right (TR)



Bottom Right (BR)



Bottom Left (BL)

In a few cases, a dedicated input is physically in one quadrant of the device but connects to a different clock quadrant:



Top Left (TL)



FT256, H16 is in clock quadrant BR

Note that the quadrant clock notation (TR, BR, BL, TL) is separate from that used for similar IOB placement constraints.



FG320, K2 is in clock quadrant BL



FG400, L8 is in clock quadrant TL and the I/O at N11 is in clock quadrant BL

To estimate the quadrant location for a particular I/O, see the footprint diagrams in Module 4, Pinout Descriptions. For exact quadrant locations, use the floorplanning tool. In the QFP packages (VQ100, TQ144 and PQ208) the quadrant borders fall in the middle of each side of the package, at a GND pin. The clock inputs fall on the quadrant boundaries, as indicated in Table 42.



FG484, M2 is in clock quadrant TL and L15 is in clock quadrant BR

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 61

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 47

BUFGMUX Output X1Y10 (Global) X0Y9 (Left Half) X1Y11 (Global) X0Y8 (Left Half) X2Y10 (Global) X0Y7 (Left Half) X2Y11 (Global) X0Y6 (Left Half) X1Y0 (Global) X0Y5 (Left Half) X1Y1 (Global) X0Y4 (Left Half) X2Y0 (Global) X0Y3 (Left Half) X2Y1 (Global) X0Y2 (Left Half)

Clock Line

H G

F E

D

C

B

A

a. Left (TL and BL Quadrants) Half of Die

BUFGMUX Output X1Y10 (Global) X3Y9 (Right Half) X1Y11 (Global) X3Y8 (Right Half) X2Y10 (Global) X3Y7 (Right Half) X2Y11 (Global) X3Y6 (Right Half) X1Y0 (Global) X3Y5 (Right Half) X1Y1 (Global) X3Y4 (Right Half) X2Y0 (Global) X3Y3 (Right Half) X2Y1 (Global) X3Y2 (Right Half)

Clock Line

H G

F E

D

C

B

A

b. Right (TR and BR Quadrants) Half of Die DS312-2_17_103105

Figure 47: Clock Sources for the Eight Clock Lines within a Clock Quadrant The outputs of the top or bottom BUFGMUX elements connect to two vertical spines, each comprising four vertical clock lines as shown in Figure 45. At the center of the die, these clock signals connect to the eight-line horizontal clock spine. Outputs of the left and right BUFGMUX elements are routed onto the left or right horizontal spines, each comprising eight horizontal clock lines. Each of the eight clock signals in a clock quadrant derives either from a global clock signal or a half clock signal. In other words, there are up to 24 total potential clock inputs to the FPGA, eight of which can connect to clocked elements in a single clock quadrant. Figure 47 shows how the clock lines in each quadrant are selected from associated BUFGMUX sources. For example, if quadrant clock ‘A’ in the bottom left (BL) quadrant originates from BUFGMUX_X2Y1, then the clock signal from BUFGMUX_X0Y2 is unavailable in the bottom left quadrant. However, the top left (TL) quadrant clock ‘A’ can still solely use the output from either BUFGMUX_X2Y1 or BUFGMUX_X0Y2 as the source. To minimize the dynamic power dissipation of the clock network, the Xilinx development software automatically disables all clock segments not in use.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 62

Spartan-3E FPGA Family: Functional Description

Interconnect

exploits the rich interconnect array to deliver optimal system performance and the fastest compile times.

For additional information, refer to the “Using Interconnect” chapter in UG331.

Switch Matrix

Interconnect is the programmable network of signal pathways between the inputs and outputs of functional elements within the FPGA, such as IOBs, CLBs, DCMs, and block RAM.

The switch matrix connects to the different kinds of interconnects across the device. An interconnect tile, shown in Figure 48, is defined as a single switch matrix connected to a functional element, such as a CLB, IOB, or DCM. If a functional element spans across multiple switch matrices such as the block RAM or multipliers, then an interconnect tile is defined by the number of switch matrices connected to that functional element. A Spartan-3E device can be represented as an array of interconnect tiles where interconnect resources are for the channel between any two adjacent interconnect tile rows or columns as shown in Figure 49.

Overview Interconnect, also called routing, is segmented for optimal connectivity. Functionally, interconnect resources are identical to that of the Spartan-3 architecture. There are four kinds of interconnects: long lines, hex lines, double lines, and direct lines. The Xilinx Place and Route (PAR) software X-Ref Target - Figure 48

Switch Matrix

CLB

Switch Matrix Switch Matrix

Switch Matrix

18Kb Block RAM

IOB Switch Matrix

Switch Matrix

DCM

MULT 18 x 18

Switch Matrix DS312_08_100110

Figure 48: Four Types of Interconnect Tiles (CLBs, IOBs, DCMs, and Block RAM/Multiplier) X-Ref Target - Figure 49

Switch Matrix

IOB

Switch Matrix

IOB

Switch Matrix

IOB

Switch Matrix

IOB

Switch Matrix

Switch Matrix

IOB

Switch Matrix

CLB

Switch Matrix

CLB

Switch Matrix

CLB

Switch Matrix

Switch Matrix

IOB

Switch Matrix

CLB

Switch Matrix

CLB

Switch Matrix

CLB

Switch Matrix

Switch Matrix

IOB

Switch Matrix

CLB

Switch Matrix

CLB

Switch Matrix

CLB

Switch Matrix

Switch Matrix

IOB

Switch Matrix

CLB

Switch Matrix

CLB

Switch Matrix

CLB

Switch Matrix DS312_09_100110

Figure 49: Array of Interconnect Tiles in Spartan-3E FPGA DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 63

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 50

6

CLB

CLB

6

CLB

CLB

6

CLB

6

CLB

•• •

CLB

•• •

CLB

•• •

CLB

•• •

24

•• •

Horizontal and Vertical Long Lines (horizontal channel shown as an example)

CLB

6 DS312-2_10_022305

Horizontal and Vertical Hex Lines (horizontal channel shown as an example)

8

CLB

CLB

CLB

CLB

CLB

CLB

CLB DS312-2_11_020905

Horizontal and Vertical Double Lines (horizontal channel shown as an example)

8

CLB

CLB

CLB DS312-2_15_022305

Direct Connections CLB

CLB

CLB

CLB

CLB

CLB

CLB

CLB

CLB DS312-2_12_020905

Figure 50: Interconnect Types between Two Adjacent Interconnect Tiles The four types of general-purpose interconnect available in each channel, shown in Figure 50, are described below.

Long Lines Each set of 24 long line signals spans the die both horizontally and vertically and connects to one out of every six interconnect tiles. At any tile, four of the long lines drive or receive signals from a switch matrix. Because of their low capacitance, these lines are well-suited for carrying high-frequency signals with minimal loading effects (e.g. skew). If all global clock lines are already committed and additional clock signals remain to be assigned, long lines serve as a good alternative.

DS312 (v4.1) July 19, 2013 Product Specification

Hex Lines Each set of eight hex lines are connected to one out of every three tiles, both horizontally and vertically. Thirty-two hex lines are available between any given interconnect tile. Hex lines are only driven from one end of the route.

Double Lines Each set of eight double lines are connected to every other tile, both horizontally and vertically. in all four directions. Thirty-two double lines available between any given interconnect tile. Double lines are more connections and more flexibility, compared to long line and hex lines.

www.xilinx.com 64

Spartan-3E FPGA Family: Functional Description

Direct Connections Direct connect lines route signals to neighboring tiles: vertically, horizontally, and diagonally. These lines most often drive a signal from a “source” tile to a double, hex, or long line and conversely from the longer interconnect back to a direct line accessing a “destination” tile.

Global Controls (STARTUP_SPARTAN3E) In addition to the general-purpose interconnect, Spartan-3E FPGAs have two global logic control signals, as described in Table 43. These signals are available to the FPGA application via the STARTUP_SPARTAN3E primitive. Table 43: Spartan-3E Global Logic Control Signals Global Control Input

Description

GSR

Global Set/Reset: When High, asynchronously places all registers and flip-flops in their initial state (see Initialization, page 32). Asserted automatically during the FPGA configuration process (see Start-Up, page 106).

GTS

Global Three-State: When High, asynchronously forces all I/O pins to a high-impedance state (Hi-Z, three-state).

The Global Set/Reset (GSR) signal replaces the global reset signal included in many ASIC-style designs. Use the GSR control instead of a separate global reset signal in the design to free up CLB inputs, resulting in a smaller, more efficient design. Similarly, the GSR signal is asserted automatically during the FPGA configuration process, guaranteeing that the FPGA starts-up in a known state. The STARTUP_SPARTAN3E primitive also includes two other signals used specifically during configuration. The MBT signals are for Dynamically Loading Multiple Configuration Images Using MultiBoot Option, page 92. The CLK input is an alternate clock for configuration Start-Up, page 106.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 65

Spartan-3E FPGA Family: Functional Description

Configuration

merely borrowed and returned to the application as general-purpose user I/Os after configuration completes.

For additional information on configuration, refer to UG332: Spartan-3 Generation Configuration User Guide.

Differences from Spartan-3 FPGAs In general, Spartan-3E FPGA configuration modes are a superset to those available in Spartan-3 FPGAs. Two new modes added in Spartan-3E FPGAs provide a glueless configuration interface to industry-standard parallel NOR Flash and SPI serial Flash memories.

Configuration Process The function of a Spartan-3E FPGA is defined by loading application-specific configuration data into the FPGA’s internal, reprogrammable CMOS configuration latches (CCLs), similar to the way a microprocessor’s function is defined by its application program. For FPGAs, this configuration process uses a subset of the device pins, some of which are dedicated to configuration; other pins are

Spartan-3E FPGAs offer several configuration options to minimize the impact of configuration on the overall system design. In some configuration modes, the FPGA generates a clock and loads itself from an external memory source, either serially or via a byte-wide data path. Alternatively, an external host such as a microprocessor downloads the FPGA’s configuration data using a simple synchronous serial interface or via a byte-wide peripheral-style interface. Furthermore, multiple-FPGA designs share a single configuration memory source, creating a structure called a daisy chain. Three FPGA pins—M2, M1, and M0—select the desired configuration mode. The mode pin settings appear in Table 44. The mode pin values are sampled during the start of configuration when the FPGA’s INIT_B output goes High. After the FPGA completes configuration, the mode pins are available as user I/Os.

Table 44: Spartan-3E Configuration Mode Options and Pin Settings Master Serial

SPI

BPI

Slave Parallel

Slave Serial

JTAG

<0:0:0>

<0:0:1>

<0:1:0>=Up <0:1:1>=Down

<1:1:0>

<1:1:1>

<1:0:1>

Serial

Serial

Byte-wide

Byte-wide

Serial

Serial

Configuration memory source

Xilinx Platform Flash

Industry-standard SPI serial Flash

Industry-standard parallel NOR Flash or Xilinx parallel Platform Flash

Any source via microcontroller, CPU, Xilinx parallel Platform Flash, etc.

Any source via microcontroller, CPU, Xilinx Platform Flash, etc.

Any source via microcontroller, CPU, System ACE™ CF, etc.

Clock source

Internal oscillator

Internal oscillator

Internal oscillator

External clock on CCLK pin

External clock on CCLK pin

External clock on TCK pin

8

13

46

21

8

0

Slave Serial

Slave Serial

Slave Parallel

Slave Parallel or Memory Mapped

Slave Serial

JTAG

M[2:0] mode pin settings Data width

Total I/O pins borrowed during configuration Configuration mode for downstream daisychained FPGAs Stand-alone FPGA applications (no external download host) Uses low-cost, industry-standard Flash Supports optional MultiBoot, multi-configuration mode

DS312 (v4.1) July 19, 2013 Product Specification











Possible using Possible using XCFxxP XCFxxP Platform Flash, Platform Flash, which optionally which optionally generates CCLK generates CCLK



www.xilinx.com 66

Spartan-3E FPGA Family: Functional Description

Configuration Bitstream Image Sizes A specific Spartan-3E part type always requires a constant number of configuration bits, regardless of design complexity, as shown in Table 45. The configuration file size for a multiple-FPGA daisy-chain design roughly equals the sum of the individual file sizes. Table 45: Number of Bits to Program a Spartan-3E FPGA (Uncompressed Bitstreams) Spartan-3E FPGA

Number of Configuration Bits

XC3S100E

581,344

XC3S250E

1,353,728

XC3S500E

2,270,208

XC3S1200E

3,841,184

XC3S1600E

5,969,696

values applied to the M2, M1, and M0 mode select pins and the HSWAP pin. The mode select pins determine which of the I/O pins are borrowed during configuration and how they function. In JTAG configuration mode, no user-I/O pins are borrowed for configuration. All user-I/O pins, input-only pins, and dual-purpose pins that are not actively involved in the currently-select configuration mode are high impedance (floating, three-stated, Hi-Z) during the configuration process. These pins are indicated in Table 46 as gray shaded table entries or cells. The HSWAP input controls whether all user-I/O pins, input-only pins, and dual-purpose pins have a pull-up resistor to the supply rail or not. When HSWAP is Low, each pin has an internal pull-up resistor that is active throughout configuration. After configuration, pull-up and pull-down resistors are available in the FPGA application as described in Pull-Up and Pull-Down Resistors.

Pin Behavior During Configuration For additional information, refer to the “Configuration Pins and Behavior during Configuration” chapter in UG332.

The yellow-shaded table entries or cells represent pins where the pull-up resistor is always enabled during configuration, regardless of the HSWAP input. The post-configuration behavior of these pins is defined by Bitstream Generator options as defined in Table 69.

Table 46 shows how various pins behave during the FPGA configuration process. The actual behavior depends on the Table 46: Pin Behavior during Configuration Pin Name

Master Serial

SPI (Serial Flash)

BPI (Parallel NOR Flash)

JTAG

Slave Parallel

Slave Serial

IO* (user-I/O) IP* (input-only)

I/O Bank(3) -

TDI TMS TCK TDO PROG_B DONE HSWAP M2 M1 M0

TDI TMS TCK TDO PROG_B DONE HSWAP 0 0 0

TDI TMS TCK TDO PROG_B DONE HSWAP 0 0 1

CCLK INIT_B CSO_B DOUT/BUSY MOSI/CSI_B D7

CCLK (I/O) INIT_B

CCLK (I/O) INIT_B CSO_B DOUT MOSI

DOUT

D6 D5 D4 D3 D2 D1 DS312 (v4.1) July 19, 2013 Product Specification

TDI TMS TCK TDO PROG_B DONE HSWAP 0 1 0 = Up 1 = Down CCLK (I/O) INIT_B CSO_B BUSY CSI_B D7

TDI TMS TCK TDO PROG_B DONE HSWAP 1 0 1

D6 D5 D4 D3 D2 D1

TDI TMS TCK TDO PROG_B DONE HSWAP 1 1 0

TDI TMS TCK TDO PROG_B DONE HSWAP 1 1 1

VCCAUX VCCAUX VCCAUX VCCAUX VCCAUX VCCAUX 0 2 2 2

CCLK (I) INIT_B CSO_B BUSY CSI_B D7

CCLK (I) INIT_B

2 2 2 2 2 2

D6 D5 D4 D3 D2 D1

DOUT

2 2 2 2 2 2

www.xilinx.com 67

Spartan-3E FPGA Family: Functional Description Table 46: Pin Behavior during Configuration (Cont’d) Pin Name

Master Serial

SPI (Serial Flash)

BPI (Parallel NOR Flash)

D0/DIN RDWR_B A23 A22 A21 A20 A19/VS2 A18/VS1 A17/VS0 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 LDC0 LDC1 LDC2 HDC

DIN

DIN

D0 RDWR_B A23 A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 LDC0 LDC1 LDC2 HDC

VS2 VS1 VS0

JTAG

Slave Parallel

Slave Serial

D0 RDWR_B

DIN

I/O Bank(3) 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Notes: 1. Gray shaded cells represent pins that are in a high-impedance state (Hi-Z, floating) during configuration. These pins have an optional internal pull-up resistor to their respective VCCO supply pin that is active throughout configuration if the HSWAP input is Low. 2. Yellow shaded cells represent pins with an internal pull-up resistor to its respective voltage supply rail that is active during configuration, regardless of the HSWAP pin. 3. Note that dual-purpose outputs are supplied by VCCO, and configuration inputs are supplied by VCCAUX.

The HSWAP pin itself has a pull-up resistor enabled during configuration. However, the VCCO_0 supply voltage must be applied before the pull-up resistor becomes active. If the VCCO_0 supply ramps after the VCCO_2 power supply, do not let HSWAP float; tie HSWAP to the desired logic level externally. Spartan-3E FPGAs have only six dedicated configuration pins, including the DONE and PROG_B pins, and the four JTAG boundary-scan pins: TDI, TDO, TMS, and TCK. All other configuration pins are dual-purpose I/O pins and are available to the FPGA application after the DONE pin goes High. See Start-Up for additional information.

DS312 (v4.1) July 19, 2013 Product Specification

Table 47 shows the default I/O standard setting for the various configuration pins during the configuration process. The configuration interface is designed primarily for 2.5V operation when the VCCO_2 (and VCCO_1 in BPI mode) connects to 2.5V. Table 47: Default I/O Standard Setting During Configuration (VCCO_2 = 2.5V) Pin(s) All, including CCLK

I/O Standard Output Drive Slew Rate LVCMOS25

8 mA

Slow

www.xilinx.com 68

Spartan-3E FPGA Family: Functional Description The configuration pins also operate at other voltages by setting VCCO_2 (and VCCO_1 in BPI mode) to either 3.3V or 1.8V. The change on the VCCO supply also changes the I/O characteristics, including the effective IOSTANDARD. For example, with VCCO = 3.3V, the output characteristics will be similar to those of LVCMOS33, and the current when driving High, IOH, increases to approximately 12 to 16 mA, while the current when driving Low, IOL, remains 8 mA. At VCCO = 1.8V, the output characteristics will be similar to those of LVCMOS18, and the current when driving High, IOH, decreases slightly to approximately 6 to 8 mA. Again, the current when driving Low, IOL, remains 8 mA. The output voltages are determined by the VCCO level, LVCMOS18 for 1.8V, LVCMOS25 for 2.5V, and LVCMOS33 for 3.3V. For more details see UG332.

CCLK Design Considerations For additional information, refer to the “Configuration Pins and Behavior during Configuration” chapter in UG332. The FPGA’s configuration process is controlled by the CCLK configuration clock. Consequently, signal integrity of CCLK is important to guarantee successful configuration. Poor CCLK signal integrity caused by ringing or reflections might cause double-clocking, causing the configuration process to fail. Although the CCLK frequency is relatively low, Spartan-3E FPGA output edge rates are fast. Therefore, careful attention must be paid to the CCLK signal integrity on the printed circuit board. Signal integrity simulation with IBIS is recommended. For all configuration modes except JTAG, the signal integrity must be considered at every CCLK trace destination, including the FPGA’s CCLK pin. This analysis is especially important when the FPGA re-uses the CCLK pin as a user-I/O after configuration. In these cases, there might be unrelated devices attached to CCLK, which add additional trace length and signal destinations. In the Master Serial, SPI, and BPI configuration modes, the FPGA drives the CCLK pin and CCLK should be treated as a full bidirectional I/O pin for signal integrity analysis. In BPI mode, CCLK is only used in multi-FPGA daisy-chains. The best signal integrity is ensured by following these basic PCB guidelines:

For additional information, refer to the “Configuration Pins and Behavior during Configuration” chapter in UG332. Unlike previous Spartan FPGA families, nearly all of the Spartan-3E dual-purpose configuration pins are available as full-featured user I/O pins after successful configuration, when the DONE output goes High. The HSWAP pin, the mode select pins (M[2:0]), and the variant-select pins (VS[2:0]) must have valid and stable logic values at the start of configuration. VS[2:0] are only used in the SPI configuration mode. The levels on the M[2:0] pins and VS[2:0] pins are sampled when the INIT_B pin returns High. See Figure 76 for a timing example. The HSWAP pin defines whether FPGA user I/O pins have a pull-up resistor connected to their associated VCCO supply pin during configuration or not, as shown Table 48. HSWAP must be valid at the start of configuration and remain constant throughout the configuration process. Table 48: HSWAP Behavior HSWAP Value

Description

0

Pull-up resistors connect to the associated VCCO supply for all user-I/O or dual-purpose I/O pins during configuration. Pull-up resistors are active until configuration completes.

1

Pull-up resistors disabled during configuration. All user-I/O or dual-purpose I/O pins are in a high-impedance state.

The Configuration section provides detailed schematics for each configuration mode. The schematics indicate the required logic values for HSWAP, M[2:0], and VS[2:0] but do not specify how the application provides the logic Low or High value. The HSWAP, M[2:0], and VS[2:0] pins can be either dedicated or reused by the FPGA application.

Dedicating the HSWAP, M[2:0], and VS[2:0] Pins If the HSWAP, M[2:0], and VS[2:0] pins are not required by the FPGA design after configuration, simply connect these pins directly to the VCCO or GND supply rail shown in the appropriate configuration schematic.

Reusing HSWAP, M[2:0], and VS[2:0] After Configuration



Route the CCLK signal as a 50 Ω controlled-impedance transmission line.



Route the CCLK signal without any branching. Do not use a “star” topology.



Keep stubs, if required, shorter than 10 mm (0.4 inches).



Terminate the end of the CCLK transmission line.

DS312 (v4.1) July 19, 2013 Product Specification

Design Considerations for the HSWAP, M[2:0], and VS[2:0] Pins

To reuse the HSWAP, M[2:0], and VS[2:0] pin after configuration, use pull-up or pull-down resistors to define the logic values shown in the appropriate configuration schematic.

www.xilinx.com 69

Spartan-3E FPGA Family: Functional Description

Table 49: Pull-up or Pull-down Values for HSWAP, M[2:0], and VS[2:0] HSWAP Value

Required Resistor Value to Define Logic Level on HSWAP, M[2:0], or VS[2:0]

I/O Pull-up Resistors during Configuration

High

Low

0

Enabled

Pulled High via an internal pull-up resistor to the associated VCCO supply. No external pull-up resistor is necessary.

Pulled Low using an appropriately sized pull-down resistor to GND. For a 2.5V or 3.3V interface: R ≤ 560Ω . For a 1.8V interface: R ≤ 1.1kΩ .

1

Disabled

Pulled High using a 3.3 to 4.7kΩ resistor to the associated VCCO supply.

Pulled Low using a 3.3 to 4.7kΩ resistor to GND.

The logic level on HSWAP dictates how to define the logic levels on M[2:0] and VS[2:0], as shown in Table 49. If the application requires HSWAP to be High, the HSWAP pin is pulled High using an external 3.3kΩ to 4.7kΩ resistor to VCCO_0. If the application requires HSWAP to be Low during configuration, then HSWAP is either connected to GND or pulled Low using an appropriately sized external pull-down resistor to GND. When HSWAP is Low, its pin has an internal pull-up resistor to VCCO_0. The external pull-down resistor must be strong enough to define a logic Low on HSWAP for the I/O standard used during configuration. For 2.5V or 3.3V I/O, the pull-down resistor is 560Ω or lower. For 1.8V I/O, the pull-down resistor is 1.1kΩ or lower. Once HSWAP is defined, use Table 49 to define the logic values for M[2:0] and VS[2:0]. Use the weakest external pull-up or pull-down resistor value allowed by the application. The resistor must be strong enough to define a logic Low or High during configuration. However, when driving the HSWAP, M[2:0], or VS[2:0] pins after configuration, the output driver must be strong enough to overcome the pull-up or pull-down resistor value and generate the appropriate logic levels. For example, to overcome a 560Ω pull-down resistor, a 3.3V FPGA I/O pin must use a 6 mA or stronger driver.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 70

Spartan-3E FPGA Family: Functional Description

Master Serial Mode For additional information, refer to the “Master Serial Mode” chapter in UG332. In Master Serial mode (M[2:0] = <0:0:0>), the Spartan-3E FPGA configures itself from an attached Xilinx Platform

Flash PROM, as illustrated in Figure 51. The FPGA supplies the CCLK output clock from its internal oscillator to the attached Platform Flash PROM. In response, the Platform Flash PROM supplies bit-serial data to the FPGA’s DIN input, and the FPGA accepts this data on each rising CCLK edge.

X-Ref Target - Figure 51

+1.2V

Serial Master Mode ‘0’ ‘0’ ‘0’

M2 M1 M0

V

Spartan-3E FPGA

XCFxxS = +3.3V XCFxxP = +1.8V

4.7k Ω

VCCO_2 DIN CCLK DOUT INIT_B

VCCO_0

VCCINT VCCO

D0 CLK

+2.5V

330 Ω

P

V

Platform Flash XCFxx CE

+2.5V JTAG TDI TMS TCK TDO

V

OE/RESET

4.7k Ω

VCCINT HSWAP VCCO_0

CEO

CF VCCAUX TDO

TDI TMS TCK

+2.5V

VCCJ TDO

TDI TMS TCK

+2.5V

GND PROG_B

DONE GND

PROG_B Recommend open-drain driver DS312-2_44_082009

Figure 51: Master Serial Mode using Platform Flash PROM All mode select pins, M[2:0], must be Low when sampled, when the FPGA’s INIT_B output goes High. After configuration, when the FPGA’s DONE output goes High, the mode select pins are available as full-featured user-I/O pins.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 71

Spartan-3E FPGA Family: Functional Description P Similarly, the FPGA’s HSWAP pin must be Low to

enable pull-up resistors on all user-I/O pins during configuration or High to disable the pull-up resistors. The HSWAP control must remain at a constant logic level throughout FPGA configuration. After configuration, when the FPGA’s DONE output goes High, the HSWAP pin is

available as full-featured user-I/O pin and is powered by the VCCO_0 supply. The FPGA's DOUT pin is used in daisy-chain applications, described later. In a single-FPGA application, the FPGA’s DOUT pin is not used but is actively driving during the configuration process.

Table 50: Serial Master Mode Connections Pin Name HSWAP

FPGA Direction

Description

During Configuration

Input

User I/O Pull-Up Control. When Low during configuration, enables pull-up resistors in all I/O pins to respective I/O bank VCCO input. 0: Pull-ups during configuration 1: No pull-ups

M[2:0]

Input

Mode Select. Selects the FPGA configuration M2 = 0, M1 = 0, M0 = 0. Sampled mode. See Design Considerations for the when INIT_B goes High. HSWAP, M[2:0], and VS[2:0] Pins.

DIN

Input

Serial Data Input.

P

Drive at valid logic level throughout configuration.

After Configuration User I/O

User I/O

Receives serial data from PROM’s User I/O D0 output.

CCLK

Output

Configuration Clock. Generated by FPGA Drives PROM’s CLK clock input. internal oscillator. Frequency controlled by ConfigRate bitstream generator option. If CCLK PCB trace is long or has multiple connections, terminate this output to maintain signal integrity. See CCLK Design Considerations.

User I/O

DOUT

Output

Serial Data Output.

Actively drives. Not used in single-FPGA designs. In a daisy-chain configuration, this pin connects to DIN input of the next FPGA in the chain.

User I/O

INIT_B

Open-drain Initialization Indicator. Active Low. Goes bidirectional Low at start of configuration during I/O Initialization memory clearing process. Released at end of memory clearing, when mode select pins are sampled. Requires external 4.7 kΩ pull-up resistor to VCCO_2.

Connects to PROM’s OE/RESET input. FPGA clears PROM’s address counter at start of configuration, enables outputs during configuration. PROM also holds FPGA in Initialization state until PROM reaches Power-On Reset (POR) state. If CRC error detected during configuration, FPGA drives INIT_B Low.

User I/O. If unused in the application, drive INIT_B High.

DONE

Open-drain FPGA Configuration Done. Low during bidirectional configuration. Goes High when FPGA I/O successfully completes configuration. Requires external 330 Ω pull-up resistor to 2.5V.

Connects to PROM’s chip-enable (CE) input. Enables PROM during configuration. Disables PROM after configuration.

Pulled High via external pull-up. When High, indicates that the FPGA successfully configured.

Must be High during configuration to allow configuration to start. Connects to PROM’s CF pin, allowing JTAG PROM programming algorithm to reprogram the FPGA.

Drive PROG_B Low and release to reprogram FPGA.

PROG_B

Input

DS312 (v4.1) July 19, 2013 Product Specification

Program FPGA. Active Low. When asserted Low for 500 ns or longer, forces the FPGA to restart its configuration process by clearing configuration memory and resetting the DONE and INIT_B pins once PROG_B returns High. Recommend external 4.7 kΩ pull-up resistor to 2.5V. Internal pull-up value may be weaker (see Table 78). If driving externally with a 3.3V output, use an open-drain or open-collector driver or use a current limiting series resistor.

www.xilinx.com 72

Spartan-3E FPGA Family: Functional Description

Voltage Compatibility The PROM’s VCCINT supply must be either 3.3V for the serial XCFxxS Platform Flash PROMs or 1.8V for the serial/parallel XCFxxP PROMs.

Table 52: Maximum ConfigRate Settings for Platform Flash Platform Flash Part Number

I/O Voltage (VCCO_2, VCCO)

Maximum ConfigRate Setting

XCF01S XCF02S XCF04S

3.3V or 2.5V

25

1.8V

12

3.3V, 2.5V, or 1.8V

25

V The FPGA’s VCCO_2 supply input and the Platform Flash PROM’s VCCO supply input must be the same voltage, ideally +2.5V. Both devices also support 1.8V and 3.3V interfaces but the FPGA’s PROG_B and DONE pins require special attention as they are powered by the FPGA’s VCCAUX supply, nominally 2.5V. See application note XAPP453: The 3.3V Configuration of Spartan-3 FPGAs for additional information.

XCF08P XCF16P XCF32P

Supported Platform Flash PROMs Table 51 shows the smallest available Platform Flash PROM to program one Spartan-3E FPGA. A multiple-FPGA daisy-chain application requires a Platform Flash PROM large enough to contain the sum of the various FPGA file sizes. Table 51: Number of Bits to Program a Spartan-3E FPGA and Smallest Platform Flash PROM Spartan-3E FPGA

Number of Configuration Bits

Smallest Available Platform Flash

XC3S100E

581,344

XCF01S

XC3S250E

1,353,728

XCF02S

XC3S500E

2,270,208

XCF04S

XC3S1200E

3,841,184

XCF04S

XC3S1600E

5,969,696

XCF08P or 2 x XCF04S

The XC3S1600E requires an 8 Mbit PROM. Two solutions are possible: either a single 8 Mbit XCF08P parallel/serial PROM or two 4 Mbit XCF04S serial PROMs cascaded. The two XCF04S PROMs use a 3.3V VCCINT supply while the XCF08P requires a 1.8V VCCINT supply. If the board does not already have a 1.8V supply available, the two cascaded XCF04S PROM solution is recommended.

CCLK Frequency In Master Serial mode, the FPGA’s internal oscillator generates the configuration clock frequency. The FPGA provides this clock on its CCLK output pin, driving the PROM’s CLK input pin. The FPGA starts configuration at its lowest frequency and increases its frequency for the remainder of the configuration process if so specified in the configuration bitstream. The maximum frequency is specified using the ConfigRate bitstream generator option. Table 52 shows the maximum ConfigRate settings, approximately equal to MHz, for various Platform Flash devices and I/O voltages. For the serial XCFxxS PROMs, the maximum frequency also depends on the interface voltage.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 73

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 52

CCLK +1.2V

+1.2V

VCCINT VCCO_0 VCCO_2 DIN CCLK DOUT INIT_B

M2 M1 M0

XCFxxS = +3.3V XCFxxP = +1.8V

P

VCCO_0

V

VCCINT D0 CLK

‘1’ ‘1’ ‘1’

OE/RESET

CE VCCAUX TDO

M2 M1 M0

VCCJ TDO

TDI TMS TCK

V

DOUT

DOUT INIT_B

CCLK DIN

CEO

+2.5V

VCCO_0

Spartan-3E FPGA

CF TDI TMS TCK

VCCINT VCCO_0 VCCO_2

Platform Flash XCFxx

Spartan-3E FPGA

VCCAUX TDO

+2.5V

+2.5V

V

TDI TMS TCK

+2.5V

GND PROG_B

PROG_B

DONE

330 Ω

+2.5V JTAG TDI TMS TCK TDO

HSWAP

Slave Serial Mode

V

VCCO

GND

4.7kΩ

Serial Master Mode ‘0’ ‘0’ ‘0’

HSWAP

4.7kΩ

P

DONE GND

PROG_B Recommend open-drain driver

PROG_B TCK TMS DONE INIT_B

DS312-2_45_082009

Figure 52: Daisy-Chaining from Master Serial Mode

Daisy-Chaining

In-System Programming Support

If the application requires multiple FPGAs with different configurations, then configure the FPGAs using a daisy chain, as shown in Figure 52. Use Master Serial mode (M[2:0] = <0:0:0>) for the FPGA connected to the Platform Flash PROM and Slave Serial mode (M[2:0] = <1:1:1>) for all other FPGAs in the daisy-chain. After the master FPGA—the FPGA on the left in the diagram—finishes loading its configuration data from the Platform Flash, the master device supplies data using its DOUT output pin to the next device in the daisy-chain, on the falling CCLK edge.

Both the FPGA and the Platform Flash PROM are in-system programmable via the JTAG chain. Download support is provided by the Xilinx iMPACT programming software and the associated Xilinx Parallel Cable IV or Platform Cable USB programming cables.

JTAG Interface Both the Spartan-3E FPGA and the Platform Flash PROM have a four-wire IEEE 1149.1/1532 JTAG port. Both devices share the TCK clock input and the TMS mode select input. The devices may connect in either order on the JTAG chain with the TDO output of one device feeding the TDI input of the following device in the chain. The TDO output of the last device in the JTAG chain drives the JTAG connector. The JTAG interface on Spartan-3E FPGAs is powered by the 2.5V VCCAUX supply. Consequently, the PROM’s VCCJ supply input must also be 2.5V. To create a 3.3V JTAG interface, please refer to application note XAPP453: The 3.3V Configuration of Spartan-3 FPGAs for additional information.

DS312 (v4.1) July 19, 2013 Product Specification

Storing Additional User Data in Platform Flash After configuration, the FPGA application can continue to use the Master Serial interface pins to communicate with the Platform Flash PROM. If desired, use a larger Platform Flash PROM to hold additional non-volatile application data, such as MicroBlaze processor code, or other user data such as serial numbers and Ethernet MAC IDs. The FPGA first configures from Platform Flash PROM. Then using FPGA logic after configuration, the FPGA copies MicroBlaze code from Platform Flash into external DDR SDRAM for code execution. See XAPP694: Reading User Data from Configuration PROMs and XAPP482: MicroBlaze Platform Flash/PROM Boot Loader and User Data Storage for specific details on how to implement such an interface.

www.xilinx.com 74

Spartan-3E FPGA Family: Functional Description

SPI Serial Flash Mode

In SPI Serial Flash mode (M[2:0] = <0:0:1>), the Spartan-3E FPGA configures itself from an attached industry-standard SPI serial Flash PROM, as illustrated in Figure 53 and Figure 54. The FPGA supplies the CCLK output clock from its internal oscillator to the clock input of the attached SPI Flash PROM.

For additional information, refer to the “Master SPI Mode” chapter in UG332.

X-Ref Target - Figure 53

+1.2V

VCCINT HSWAP VCCO_0 VCCO_2 MOSI DIN CSO_B

SPI Mode M2 M1 M0

+2.5V JTAG TDI TMS TCK TDO

VCC

W ‘1’

VS2 VS1 VS0

P

DATA_IN DATA_OUT SELECT WR_PROTECT HOLD CLOCK GND +3.3V

CCLK DOUT INIT_B VCCAUX TDO

TDI TMS TCK

+2.5V

+2.5V

PROG_B

4.7k

‘1’

I

4.7k

S

+3.3V

Spartan-3E FPGA

Variant Select ‘1’

VCCO_0

SPI Serial Flash

330

‘0’ ‘0’ ‘1’

4.7k

P

+3.3V

DONE GND

PROG_B Recommend open-drain driver

DS312-2_46_082009

Figure 53: SPI Flash PROM Interface for PROMs Supporting READ (0x03) and FAST_READ (0x0B) Commands S Although SPI is a standard four-wire interface, various

available SPI Flash PROMs use different command protocols. The FPGA’s variant select pins, VS[2:0], define how the FPGA communicates with the SPI Flash, including which SPI Flash command the FPGA issues to start the read operation and the number of dummy bytes inserted before the FPGA expects to receive valid data from the SPI Flash. Table 53 shows the available SPI Flash PROMs expected to operate with Spartan-3E FPGAs. Other compatible devices might work but have not been tested for suitability with Spartan-3E FPGAs. All other VS[2:0] values are reserved for future use. Consult the data sheet for the desired SPI Flash device to determine its suitability. The basic timing requirements and waveforms are provided in

DS312 (v4.1) July 19, 2013 Product Specification

Serial Peripheral Interface (SPI) Configuration Timing in Module 3. Figure 53 shows the general connection diagram for those SPI Flash PROMs that support the 0x03 READ command or the 0x0B FAST READ commands. Figure 54 shows the connection diagram for Atmel DataFlash serial PROMs, which also use an SPI-based protocol. ‘B’-series DataFlash devices are limited to FPGA applications operating over the commercial temperature range. Industrial temperature range applications must use ‘C’- or ‘D’-series DataFlash devices, which have a shorter DataFlash select setup time, because of the faster FPGA CCLK frequency at cold temperatures.

www.xilinx.com 75

Spartan-3E FPGA Family: Functional Description Figure 57, page 83 demonstrates how to configure multiple FPGAs with different configurations, all stored in a single SPI Flash. The diagram uses standard SPI Flash memories

but the same general technique applies for Atmel DataFlash.

X-Ref Target - Figure 54

+1.2V

+3.3V

Atmel AT45DB DataFlash

P

HSWAP

VCCO_0 VCCO_2

4.7k

VCCINT VCCO_0 +3.3V

I

VCC

MOSI

SPI Mode

DIN

W

M1

‘1’

M0

Spartan-3E FPGA

Variant Select ‘1’ ‘1’ ‘0’

CSO_B

M2

SI SO CS WP RESET RDY/BUSY SCK

VS2

GND

+3.3V

VS1 VS0

CCLK

+3.3V

DOUT

INIT_B

INIT_B VCCAUX TMS

TCK

TCK

Power-On Monitor

TDO

TDO PROG_B

4.7k

TDI

TMS

+2.5V

+2.5V

330

+2.5V JTAG TDI

Power-on monitor is only required if +3.3V (VCCO_2) supply is the last supply in power-on sequence, after VCCINT and VCCAUX. Must delay FPGA configuration for > 20 ms after SPI DataFlash reaches its minimum VCC. Force FPGA INIT_B input OR PROG_B input Low with an open-drain or opencollector driver.

4.7k

‘0’ ‘0’ ‘1’

P

or

DONE

+3.3V

GND

PROG_B

PROG_B Recommend open-drain driver

Power-On Monitor

DS312-2_50a_082009

Figure 54: Atmel SPI-based DataFlash Configuration Interface

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 76

Spartan-3E FPGA Family: Functional Description

Table 53: Variant Select Codes for Various SPI Serial Flash PROMs VS2

VS1

VS0

SPI Read Command

Dummy Bytes

SPI Serial Flash Vendor

STMicroelectronics (ST)

Atmel

SPI Flash Family

iMPACT Programming Support

M25Pxx M25PExx/M45PExx

Yes

AT45DB ‘D’-Series Data Flash

Yes

AT26 / AT25(1)

1

1

1

1

0

1

1

1

0

Others

FAST READ (0x0B) (see Figure 53)

READ (0x03) (see Figure 53)

READ ARRAY (0xE8) (see Figure 54)

1

0

4

Intel

S33

Spansion (AMD, Fujitsu)

S25FLxxxA

Winbond (NexFlash)

NX25 / W25

Macronix

MX25Lxxxx

Silicon Storage Technology (SST)

SST25LFxxxA SST25VFxxxA

Programmable Microelectronics Corp. (PMC)

Pm25LVxxx

AMIC Technology

A25L

Eon Silicon Solution, Inc.

EN25

STMicroelectronics (ST)

M25Pxx M25PExx/M45PExx

Spansion (AMD, Fujitsu)

S25FLxxxA

Winbond (NexFlash)

NX25 / W25

Macronix

MX25Lxxxx

Silicon Storage Technology (SST)

SST25LFxxxA SST25VFxxxA SST25VFxxx

Programmable Microelectronics Corp. (PMC)

Pm25LVxxx

Atmel Corporation

AT45DB DataFlash (use only ‘C’ or ‘D’ Series for Industrial temperature range)

Yes

Yes

Reserved

Notes: 1. See iMPACT documentation for specific device support.

WRITER NOTE: Many of the URLs in this table are obsolete or otherwise broken.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 77

Spartan-3E FPGA Family: Functional Description W Table 54 shows the connections between the SPI Flash

PROM and the FPGA’s SPI configuration interface. Each SPI Flash PROM vendor uses slightly different signal naming. The SPI Flash PROM’s write protect and hold

controls are not used by the FPGA during configuration. However, the HOLD pin must be High during the configuration process. The PROM’s write protect input must be High in order to write or program the Flash memory.

Table 54: Example SPI Flash PROM Connections and Pin Naming SPI Flash Pin

FPGA Connection

STMicro

NexFlash

Silicon Storage Technology

Atmel DataFlash

DATA_IN

MOSI

D

DI

SI

SI

DATA_OUT

DIN

Q

DO

SO

SO

SELECT

CSO_B

S

CS

CE#

CS

CLOCK

CCLK

C

CLK

SCK

SCK

WR_PROTECT

Not required for FPGA configuration. Must be High to program SPI Flash. Optional connection to FPGA user I/O after configuration.

W

WP

WP#

WP

HOLD (see Figure 53)

Not required for FPGA configuration but must be High during configuration. Optional connection to FPGA user I/O after configuration. Not applicable to Atmel DataFlash.

HOLD

HOLD

HOLD#

N/A

RESET (see Figure 54)

Only applicable to Atmel DataFlash. Not required for FPGA configuration but must be High during configuration. Optional connection to FPGA user I/O after configuration. Do not connect to FPGA’s PROG_B as this will prevent direct programming of the DataFlash.

N/A

N/A

N/A

RESET

RDY/BUSY (see Figure 54)

Only applicable to Atmel DataFlash and only available on certain packages. Not required for FPGA configuration. Output from DataFlash PROM. Optional connection to FPGA user I/O after configuration.

N/A

N/A

N/A

RDY/BUSY

W

The mode select pins, M[2:0], and the variant select pins, VS[2:0] are sampled when the FPGA’s INIT_B output goes High and must be at defined logic levels during this time. After configuration, when the FPGA’s DONE output goes High, these pins are all available as full-featured user-I/O pins.

disable the pull-up resistors. The HSWAP control must remain at a constant logic level throughout FPGA configuration. After configuration, when the FPGA’s DONE output goes High, the HSWAP pin is available as full-featured user-I/O pin and is powered by the VCCO_0 supply. In a single-FPGA application, the FPGA’s DOUT pin is not used but is actively driving during the configuration process.

P Similarly, the FPGA’s HSWAP pin must be Low to

enable pull-up resistors on all user-I/O pins or High to Table 55: Serial Peripheral Interface (SPI) Connections Pin Name HSWAP

FPGA Direction

During Configuration

After Configuration

Input

User I/O Pull-Up Control. When Low during configuration, enables pull-up resistors in all I/O pins to respective I/O bank VCCO input. 0: Pull-ups during configuration 1: No pull-ups

Drive at valid logic level throughout configuration.

User I/O

Input

Mode Select. Selects the FPGA configuration mode. See Design Considerations for the HSWAP, M[2:0], and VS[2:0] Pins.

M2 = 0, M1 = 0, M0 = 1. Sampled when INIT_B goes High.

User I/O

P

M[2:0]

Description

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 78

Spartan-3E FPGA Family: Functional Description Table 55: Serial Peripheral Interface (SPI) Connections (Cont’d) Pin Name VS[2:0]

FPGA Direction Input

S MOSI

DIN

Output

Input

Description

During Configuration

After Configuration

Variant Select. Instructs the FPGA how Must be at the logic levels shown User I/O to communicate with the attached SPI in Table 53. Sampled when Flash PROM. See Design Considerations INIT_B goes High. for the HSWAP, M[2:0], and VS[2:0] Pins. Serial Data Output.

FPGA sends SPI Flash memory read commands and starting address to the PROM’s serial data input.

User I/O

Serial Data Input.

FPGA receives serial data from PROM’s serial data output.

User I/O

CSO_B

Output

Chip Select Output. Active Low.

Connects to the SPI Flash PROM’s chip-select input. If HSWAP = 1, connect this signal to a 4.7 kΩ pull-up resistor to 3.3V.

Drive CSO_B High after configuration to disable the SPI Flash and reclaim the MOSI, DIN, and CCLK pins. Optionally, re-use this pin and MOSI, DIN, and CCLK to continue communicating with SPI Flash.

CCLK

Output

Configuration Clock. Generated by FPGA internal oscillator. Frequency controlled by ConfigRate bitstream generator option. If CCLK PCB trace is long or has multiple connections, terminate this output to maintain signal integrity. See CCLK Design Considerations.

Drives PROM’s clock input.

User I/O

DOUT

Output

Serial Data Output.

Actively drives. Not used in single-FPGA designs. In a daisy-chain configuration, this pin connects to DIN input of the next FPGA in the chain.

User I/O

INIT_B

Open-drain bidirectional I/O

Initialization Indicator. Active Low. Goes Low at start of configuration during Initialization memory clearing process. Released at end of memory clearing, when mode select pins are sampled. In daisy-chain applications, this signal requires an external 4.7 kΩ pull-up resistor to VCCO_2.

Active during configuration. If SPI Flash PROM requires > 2 ms to awake after powering on, hold INIT_B Low until PROM is ready. If CRC error detected during configuration, FPGA drives INIT_B Low.

User I/O. If unused in the application, drive INIT_B High.

DONE

Open-drain bidirectional I/O

FPGA Configuration Done. Low during configuration. Goes High when FPGA successfully completes configuration. Requires external 330 Ω pull-up resistor to 2.5V.

Low indicates that the FPGA is not yet configured.

Pulled High via external pull-up. When High, indicates that the FPGA successfully configured.

PROG_B

Input

DS312 (v4.1) July 19, 2013 Product Specification

Program FPGA. Active Low. When Must be High to allow asserted Low for 500 ns or longer, forces configuration to start. the FPGA to restart its configuration process by clearing configuration memory and resetting the DONE and INIT_B pins once PROG_B returns High. Recommend external 4.7 kΩ pull-up resistor to 2.5V. Internal pull-up value may be weaker (see Table 78). If driving externally with a 3.3V output, use an open-drain or open-collector driver or use a current limiting series resistor.

Drive PROG_B Low and release to reprogram FPGA. Hold PROG_B to force FPGA I/O pins into Hi-Z, allowing direct programming access to SPI Flash PROM pins.

www.xilinx.com 79

Spartan-3E FPGA Family: Functional Description

Voltage Compatibility Available SPI Flash PROMs use a single 3.3V supply voltage. All of the FPGA’s SPI Flash interface signals are within I/O Bank 2. Consequently, the FPGA’s VCCO_2 supply voltage must also be 3.3V to match the SPI Flash PROM.

Power-On Precautions if 3.3V Supply is Last in Sequence Spartan-3E FPGAs have a built-in power-on reset (POR) circuit, as shown in Figure 66, page 103. The FPGA waits

for its three power supplies — VCCINT, VCCAUX, and VCCO to I/O Bank 2 (VCCO_2) — to reach their respective power-on thresholds before beginning the configuration process. The SPI Flash PROM is powered by the same voltage supply feeding the FPGA's VCCO_2 voltage input, typically 3.3V. SPI Flash PROMs specify that they cannot be accessed until their VCC supply reaches its minimum data sheet voltage, followed by an additional delay. For some devices, this additional delay is as little as 10 µs as shown in Table 56. For other vendors, this delay is as much as 20 ms.

Table 56: Example Minimum Power-On to Select Times for Various SPI Flash PROMs Data Sheet Minimum Time from VCC min to Select = Low

SPI Flash PROM Part Number

Vendor

Symbol

Value

Units

M25Pxx

TVSL

10

μs

Spansion

S25FLxxxA

tPU

10

ms

NexFlash

NX25xx

TVSL

10

μs

STMicroelectronics

Macronix

MX25Lxxxx

tVSL

10

μs

Silicon Storage Technology

SST25LFxx

TPU-READ

10

μs

Programmable Microelectronics Corporation

Pm25LVxxx

TVCS

50

μs

AT45DBxxxD

tVCSL

30

μs

20

ms

Atmel Corporation

AT45DBxxxB

In many systems, the 3.3V supply feeding the FPGA's VCCO_2 input is valid before the FPGA's other VCCINT and VCCAUX supplies, and consequently, there is no issue. However, if the 3.3V supply feeding the FPGA's VCCO_2

supply is last in the sequence, a potential race occurs between the FPGA and the SPI Flash PROM, as shown in Figure 55.

X-Ref Target - Figure 55

3.3V Supply SPI Flash cannot be selected SPI Flash PROM minimum voltage

SPI Flash available for read operations SPI Flash PROM CS delay (tVSL )

FPGA VCCO_2 minimum Power On Reset Voltage

(VCCO2T ) (VCCINT, VCCAUX already valid)

FPGA initializes configuration memory (TPOR) Time

SPI Flash PROM must be ready for FPGA access, otherwise delay FPGA configuration FPGA accesses SPI Flash PROM DS312-2_50b_110206

Figure 55: SPI Flash PROM/FPGA Power-On Timing if 3.3V Supply is Last in Power-On Sequence If the FPGA's VCCINT and VCCAUX supplies are already valid, then the FPGA waits for VCCO_2 to reach its minimum threshold voltage before starting configuration. This threshold voltage is labeled as VCCO2T in Table 74 of Module 3 and ranges from approximately 0.4V to 1.0V, substantially lower than the SPI Flash PROM's minimum voltage. Once all three FPGA supplies reach their

DS312 (v4.1) July 19, 2013 Product Specification

respective Power On Reset (POR) thresholds, the FPGA starts the configuration process and begins initializing its internal configuration memory. Initialization requires approximately 1 ms (TPOR, minimum in Table 111 of Module 3, after which the FPGA de-asserts INIT_B, selects the SPI Flash PROM, and starts sending the appropriate read command. The SPI Flash PROM must be ready for

www.xilinx.com 80

Spartan-3E FPGA Family: Functional Description read operations at this time. Spartan-3E FPGAs issue the read command just once. If the SPI Flash is not ready, then the FPGA does not properly configure. If the 3.3V supply is last in the sequence and does not ramp fast enough, or if the SPI Flash PROM cannot be ready when required by the FPGA, delay the FPGA configuration process by holding either the FPGA's PROG_B input or INIT_B input Low, as highlighted in Figure 54. Release the FPGA when the SPI Flash PROM is ready. For example, a simple R-C delay circuit attached to the INIT_B pin forces the FPGA to wait for a preselected amount of time. Alternately, a Power Good signal from the 3.3V supply or a system reset signal accomplishes the same purpose. Use an open-drain or open-collector output when driving PROG_B or INIT_B.

SPI Flash PROM Density Requirements Table 57 shows the smallest usable SPI Flash PROM to program a single Spartan-3E FPGA. Commercially available SPI Flash PROMs range in density from 1 Mbit to 128 Mbits. A multiple-FPGA daisy-chained application requires a SPI Flash PROM large enough to contain the sum of the FPGA file sizes. An application can also use a larger-density SPI Flash PROM to hold additional data beyond just FPGA configuration data. For example, the SPI Flash PROM can also store application code for a MicroBlaze™ RISC processor core integrated in the Spartan-3E FPGA. See Using the SPI Flash Interface after Configuration. Table 57: Number of Bits to Program a Spartan-3E FPGA and Smallest SPI Flash PROM Device

Number of Configuration Bits

Smallest Usable SPI Flash PROM

XC3S100E

581,344

1 Mbit

XC3S250E

1,353,728

2 Mbit

XC3S500E

2,270,208

4 Mbit

XC3S1200E

3,841,184

4 Mbit

XC3S1600E

5,969,696

8 Mbit

CCLK Frequency In SPI Flash mode, the FPGA’s internal oscillator generates the configuration clock frequency. The FPGA provides this clock on its CCLK output pin, driving the PROM’s clock input pin. The FPGA starts configuration at its lowest frequency and increases its frequency for the remainder of the configuration process if so specified in the configuration bitstream. The maximum frequency is specified using the ConfigRate bitstream generator option. The maximum frequency supported by the FPGA configuration logic depends on the timing for the SPI Flash device. Without examining the timing for a specific SPI Flash PROM, use ConfigRate = 12 or lower. SPI Flash PROMs that support the FAST READ command support higher data rates. Some DS312 (v4.1) July 19, 2013 Product Specification

such PROMs support up to ConfigRate = 25 and beyond but require careful data sheet analysis. See Serial Peripheral Interface (SPI) Configuration Timing for more detailed timing analysis.

Using the SPI Flash Interface after Configuration After the FPGA successfully completes configuration, all of the pins connected to the SPI Flash PROM are available as user-I/O pins. If not using the SPI Flash PROM after configuration, drive CSO_B High to disable the PROM. The MOSI, DIN, and CCLK pins are then available to the FPGA application. Because all the interface pins are user I/O after configuration, the FPGA application can continue to use the SPI Flash interface pins to communicate with the SPI Flash PROM, as shown in Figure 56. SPI Flash PROMs offer random-accessible, byte-addressable, read/write, non-volatile storage to the FPGA application. SPI Flash PROMs are available in densities ranging from 1 Mbit up to 128 Mbits. However, a single Spartan-3E FPGA requires less than 6 Mbits. If desired, use a larger SPI Flash PROM to contain additional non-volatile application data, such as MicroBlaze processor code, or other user data such as serial numbers and Ethernet MAC IDs. In the example shown in Figure 56, the FPGA configures from SPI Flash PROM. Then using FPGA logic after configuration, the FPGA copies MicroBlaze code from SPI Flash into external DDR SDRAM for code execution. Similarly, the FPGA application can store non-volatile application data within the SPI Flash PROM. The FPGA configuration data is stored starting at location 0. Store any additional data beginning in the next available SPI Flash PROM sector or page. Do not mix configuration data and user data in the same sector or page. Similarly, the SPI bus can be expanded to additional SPI peripherals. Because SPI is a common industry-standard interface, various SPI-based peripherals are available, such as analog-to-digital (A/D) converters, digital-to-analog (D/A) converters, CAN controllers, and temperature sensors. However, if sufficient I/O pins are available in the application, Xilinx recommends creating a separate SPI bus to control peripherals. Creating a second port reduces the loading on the CCLK and DIN pins, which are crucial for configuration. The MOSI, DIN, and CCLK pins are common to all SPI peripherals. Connect the select input on each additional SPI peripheral to one of the FPGA user I/O pins. If HSWAP = 0 during configuration, the FPGA holds the select line High. If HSWAP = 1, connect the select line to +3.3V via an external 4.7 kΩ pull-up resistor to avoid spurious read or write operations. After configuration, drive the select line Low to select the desired SPI peripheral.

www.xilinx.com 81

Spartan-3E FPGA Family: Functional Description During the configuration process, CCLK is controlled by the FPGA and limited to the frequencies generated by the FPGA. After configuration, the FPGA application can use

other clock signals to drive the CCLK pin and can further optimize SPI-based communication. Refer to the individual SPI peripheral data sheet for specific interface and communication protocol requirements.

X-Ref Target - Figure 56

Spartan-3E FPGA

FPGA-based SPI Master

MOSI DIN

DATA_OUT

CCLK

CLOCK

CSO_B User I/O

User Data

DATA_IN

SELECT +3.3V 4.7k

MicroBlaze

DDR SDRAM

SPI Serial Flash PROM

FFFFF

MicroBlaze Code FPGA Configuration

0

SPI Peripherals DATA_IN DATA_OUT CLOCK SELECT

- A/D Converter - D/A Converter - CAN Controller - Displays - Temperature Sensor - ASSP

To other SPI slave peripherals

DS312-2_47_082009

Figure 56: Using the SPI Flash Interface After Configuration

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 82

Spartan-3E FPGA Family: Functional Description

Daisy-Chaining diagram—finishes loading its configuration data from the SPI Flash PROM, the master device uses its DOUT output pin to supply data to the next device in the daisy-chain, on the falling CCLK edge.

If the application requires multiple FPGAs with different configurations, then configure the FPGAs using a daisy chain, as shown in Figure 57. Daisy-chaining from a single SPI serial Flash PROM is supported in Stepping 1 devices. It is not supported in Stepping 0 devices. Use SPI Flash mode (M[2:0] = <0:0:1>) for the FPGA connected to the Platform Flash PROM and Slave Serial mode (M[2:0] = <1:1:1>) for all other FPGAs in the daisy-chain. After the master FPGA—the FPGA on the left in the

Design Note SPI mode daisy chains are supported only in Stepping 1 silicon versions.

X-Ref Target - Figure 57

SPI-based daisy-chaining is

! only supported in Stepping 1.

CCLK

+1.2V

VCCINT HSWAP VCCO_0 VCCO_2 MOSI DIN CSO_B

SPI Mode M2 M1 M0

‘1’

VCC DATA_IN DATA_OUT SELECT WR_PROTECT HOLD CLOCK

W ‘1’

VS2 VS1 VS0

VCCAUX TDO

TDI TMS TCK

HSWAP

VCCINT VCCO_0 VCCO_2

Slave Serial Mode ‘1’ ‘1’ ‘1’

+3.3V

330

DOUT

DOUT INIT_B VCCAUX TDO

TDI TMS TCK PROG_B

GND

+3.3V

Spartan-3E FPGA

+2.5V

DONE

VCCO_0

M2 M1 M0

CCLK DIN

+2.5V

PROG_B

P

GND

CCLK DOUT INIT_B

+2.5V JTAG TDI TMS TCK TDO

I

4.7k

‘1’

+3.3V

P

Spartan-3E FPGA

Variant Select

S

VCCO_0

SPI Serial Flash

4.7k

‘0’ ‘0’ ‘1’

4.7k

P

+1.2V

+3.3V

+2.5V

DONE GND

PROG_B

PROG_B Recommend open-drain driver

TCK TMS DONE INIT_B

DS312-2_48_082009

Figure 57: Daisy-Chaining from SPI Flash Mode (Stepping 1)

Programming Support For successful daisy-chaining, the DONE_cycle configuration option must be set to cycle 5 or sooner. The default cycle is 4. See Table 69 and the Start-Up section for additional information. I In production applications, the SPI Flash PROM is

usually pre-programmed before it is mounted on the printed circuit board. The Xilinx ISE development software produces industry-standard programming files that can be used with third-party gang programmers. Consult your specific SPI Flash vendor for recommended production programming solutions.

DS312 (v4.1) July 19, 2013 Product Specification

In-system programming support is available from some third-party PROM programmers using a socket adapter with attached wires. To gain access to the SPI Flash signals, drive the FPGA’s PROG_B input Low with an open-drain driver. This action places all FPGA I/O pins, including those attached to the SPI Flash, in high-impedance (Hi-Z). If the HSWAP input is Low, the I/Os have pull-up resistors to the VCCO input on their respective I/O bank. The external programming hardware then has direct access to the SPI Flash pins. The programming access points are highlighted in the gray box in Figure 53, Figure 54, and Figure 57. Beginning with the Xilinx ISE 8.2i software release, the iMPACT programming utility provides direct, in-system prototype programming support for STMicro M25P-series

www.xilinx.com 83

Spartan-3E FPGA Family: Functional Description SPI serial Flash PROMs and the Atmel AT45DB-series Data Flash PROMs using the Platform Cable USB, Xilinx Parallel IV, or other compatible programming cable.

Byte-Wide Peripheral Interface (BPI) Parallel Flash Mode For additional information, refer to the “Master BPI Mode” chapter in UG332. In Byte-wide Peripheral Interface (BPI) mode (M[2:0] = <0:1:0> or <0:1:1>), a Spartan-3E FPGA configures itself from an industry-standard parallel NOR Flash PROM, as illustrated in Figure 58. The FPGA generates up to a 24-bit address lines to access an attached parallel Flash. Only 20 address lines are generated for Spartan-3E FPGAs in the TQ144 package. Similarly, the XC3S100E FPGA in the CP132 package only has 20 address lines while the XC3S250E and XC3S500E FPGAs in the same package have 24 address lines. When using the VQ100 package, the BPI mode is not available when using parallel NOR Flash, but is supported using parallel Platform Flash (XCFxxP). The BPI configuration interface is primarily designed for standard parallel NOR Flash PROMs and supports both byte-wide (x8) and byte-wide/halfword (x8/x16) PROMs. The interface functions with halfword-only (x16) PROMs, but the upper byte in a portion of the PROM remains unused. For configuration, the BPI interface does not require any specific Flash PROM features, such as boot block or a specific sector size. The BPI interface also functions with Xilinx parallel Platform Flash PROMs (XCFxxP), although the FPGA’s address lines are left unconnected. The BPI interface also works equally wells with other asynchronous memories that use a similar SRAM-style interface such as SRAM, NVRAM, EEPROM, EPROM, or masked ROM. NAND Flash memory is commonly used in memory cards for digital cameras. Spartan-3E FPGAs do not configure directly from NAND Flash memories. The FPGA’s internal oscillator controls the interface timing and the FPGA supplies the clock on the CCLK output pin. However, the CCLK signal is not used in single FPGA applications. Similarly, the FPGA drives three pins Low during configuration (LDC[2:0]) and one pin High during configuration (HDC) to the PROM’s control inputs.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 84

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 58

+1.2V

V VCCINT HSWAP

VCCO_0

VCCO_0

I VCCO_1 LDC0

CE#

LDC1

OE#

HDC

WE#

D

A[16:0] DQ[15:7]

BPI Mode

VCCO_2

‘0’ ‘1’

M2

D[7:0]

M1

A[23:17]

A

M0

V DQ[7:0] A[n:0]

V

CCLK CSI_B

CSO_B

RDWR_B

INIT_B

+2.5V JTAG

VCCAUX TDI TMS

TCK

TCK

+2.5V

+2.5V

TDO 330

TDI TMS

GND

4.7k

Spartan-3E BUSY FPGA ‘0’ ‘0’

x8 or x8/x16 Flash PROM

BYTE#

LDC2

Not available in VQ100 package

VCCO

V

TDO PROG_B

4.7k

P

DONE GND

PROG_B

Recommend open-drain driver

DS312-2_49_082009

Figure 58: Byte-wide Peripheral Interface (BPI) Mode Configured from Parallel NOR Flash PROMs A During configuration, the value of the M0 mode pin

determines how the FPGA generates addresses, as shown Table 58. When M0 = 0, the FPGA generates addresses starting at 0 and increments the address on every falling CCLK edge. Conversely, when M0 = 1, the FPGA generates addresses starting at 0xFF_FFFF (all ones) and decrements the address on every falling CCLK edge. Table 58: BPI Addressing Control M2

M1

0

1

M0

Start Address

0

0

Incrementing

1

0xFF_FFFF

Decrementing

DS312 (v4.1) July 19, 2013 Product Specification

Addressing

www.xilinx.com 85

Spartan-3E FPGA Family: Functional Description This addressing flexibility allows the FPGA to share the parallel Flash PROM with an external or embedded processor. Depending on the specific processor architecture, the processor boots either from the top or bottom of memory. The FPGA is flexible and boots from the opposite end of memory from the processor. Only the processor or the FPGA can boot at any given time. The FPGA can configure first, holding the processor in reset or the processor can boot first, asserting the FPGA’s PROG_B pin. The mode select pins, M[2:0], are sampled when the FPGA’s INIT_B output goes High and must be at defined logic levels during this time. After configuration, when the FPGA’s DONE output goes High, the mode pins are available as full-featured user-I/O pins. P Similarly, the FPGA’s HSWAP pin must be Low to

enable pull-up resistors on all user-I/O pins or High to disable the pull-up resistors. The HSWAP control must remain at a constant logic level throughout FPGA configuration. After configuration, when the FPGA’s DONE output goes High, the HSWAP pin is available as

full-featured user-I/O pin and is powered by the VCCO_0 supply. The RDWR_B and CSI_B must be Low throughout the configuration process. After configuration, these pins also become user I/O. In a single-FPGA application, the FPGA’s CSO_B and CCLK pins are not used but are actively driving during the configuration process. The BUSY pin is not used but also actively drives during configuration and is available as a user I/O after configuration. After configuration, all of the interface pins except DONE and PROG_B are available as user I/Os. Furthermore, the bidirectional SelectMAP configuration peripheral interface (see Slave Parallel Mode) is available after configuration. To continue using SelectMAP mode, set the Persist bitstream generator option to Yes. An external host can then read and verify configuration data. The Persist option will maintain A20-A23 as configuration pins although they are not used in SelectMAP mode.

Table 59: Byte-Wide Peripheral Interface (BPI) Connections Pin Name

FPGA Direction

Description

During Configuration

After Configuration

HSWAP P

Input

User I/O Pull-Up Control. When Low during configuration, enables pull-up resistors in all I/O pins to respective I/O bank VCCO input. 0: Pull-ups during configuration 1: No pull-ups

Drive at valid logic level throughout User I/O configuration.

M[2:0]

Input

Mode Select. Selects the FPGA configuration mode. See Design Considerations for the HSWAP, M[2:0], and VS[2:0] Pins.

M2 = 0, M1 = 1. Set M0 = 0 to start User I/O at address 0, increment addresses. Set M0 = 1 to start at address 0xFFFFFF and decrement addresses. Sampled when INIT_B goes High.

CSI_B

Input

Chip Select Input. Active Low.

Must be Low throughout configuration.

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

RDWR_B

Input

Read/Write Control. Active Low write enable. Read functionality typically only used after configuration, if bitstream option Persist=Yes.

Must be Low throughout configuration.

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

A

LDC0

Output

PROM Chip Enable

Connect to PROM chip-select input (CE#). FPGA drives this signal Low throughout configuration.

User I/O. If the FPGA does not access the PROM after configuration, drive this pin High to deselect the PROM. A[23:0], D[7:0], LDC[2:1], and HDC then become available as user I/O.

LDC1

Output

PROM Output Enable

Connect to the PROM output-enable input (OE#). The FPGA drives this signal Low throughout configuration.

User I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 86

Spartan-3E FPGA Family: Functional Description Table 59: Byte-Wide Peripheral Interface (BPI) Connections (Cont’d) Pin Name

FPGA Direction

Description

During Configuration

After Configuration

HDC

Output

PROM Write Enable

Connect to PROM write-enable input (WE#). FPGA drives this signal High throughout configuration.

LDC2

Output

PROM Byte Mode

This signal is not used for x8 User I/O. Drive this pin High PROMs. For PROMs with a x8/x16 after configuration to use a data width control, connect to x8/x16 PROM in x16 mode. PROM byte-mode input (BYTE#). See Precautions Using x8/x16 Flash PROMs. FPGA drives this signal Low throughout configuration.

A[23:0]

Output

Address

Connect to PROM address inputs. User I/O High-order address lines may not be available in all packages and not all may be required. Number of address lines required depends on the size of the attached Flash PROM. FPGA address generation controlled by M0 mode pin. Addresses presented on falling CCLK edge. Only 20 address lines are available in TQ144 package.

D[7:0]

Input

Data Input

FPGA receives byte-wide data on these pins in response the address presented on A[23:0]. Data captured by FPGA on rising edge of CCLK.

Not used in single FPGA User I/O applications. In a daisy-chain configuration, this pin connects to the CSI_B pin of the next FPGA in the chain. If HSWAP = 1 in a multi-FPGA daisy-chain application, connect this signal to a 4.7 kΩ pull-up resistor to VCCO_2. Actively drives Low when selecting a downstream device in the chain.

D

User I/O

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

CSO_B

Output

Chip Select Output. Active Low.

BUSY

Output

Busy Indicator. Typically only used Not used during configuration but after configuration, if bitstream actively drives. option Persist=Yes.

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

CCLK

Output

Configuration Clock. Generated by FPGA internal oscillator. Frequency controlled by ConfigRate bitstream generator option. If CCLK PCB trace is long or has multiple connections, terminate this output to maintain signal integrity. See CCLK Design Considerations.

Not used in single FPGA applications but actively drives. In a daisy-chain configuration, drives the CCLK inputs of all other FPGAs in the daisy-chain.

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

INIT_B

Open-drain bidirectional I/O

Initialization Indicator. Active Low. Goes Low at start of configuration during the Initialization memory clearing process. Released at the end of memory clearing, when the mode select pins are sampled. In daisy-chain applications, this signal requires an external 4.7 kΩ pull-up resistor to VCCO_2.

Active during configuration. If CRC User I/O. If unused in the error detected during application, drive INIT_B configuration, FPGA drives INIT_B High. Low.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 87

Spartan-3E FPGA Family: Functional Description Table 59: Byte-Wide Peripheral Interface (BPI) Connections (Cont’d) Pin Name DONE

FPGA Direction

Description

During Configuration

After Configuration

Open-drain bidirectional I/O

FPGA Configuration Done. Low Low indicates that the FPGA is not during configuration. Goes High yet configured. when FPGA successfully completes configuration. Requires external 330 Ω pull-up resistor to 2.5V.

Pulled High via external pull-up. When High, indicates that the FPGA is successfully configured.

Input

Program FPGA. Active Low. When Must be High to allow configuration asserted Low for 500 ns or longer, to start. forces the FPGA to restart its configuration process by clearing configuration memory and resetting the DONE and INIT_B pins once PROG_B returns High. Recommend external 4.7 kΩ pull-up resistor to 2.5V. Internal pull-up value may be weaker (see Table 78). If driving externally with a 3.3V output, use an open-drain or open-collector driver or use a current limiting series resistor.

Drive PROG_B Low and release to reprogram FPGA. Hold PROG_B to force FPGA I/O pins into Hi-Z, allowing direct programming access to Flash PROM pins.

PROG_B

Voltage Compatibility V The FPGA’s parallel Flash interface signals are within

I/O Banks 1 and 2. The majority of parallel Flash PROMs use a single 3.3V supply voltage. Consequently, in most cases, the FPGA’s VCCO_1 and VCCO_2 supply voltages must also be 3.3V to match the parallel Flash PROM. There are some 1.8V parallel Flash PROMs available and the FPGA interfaces with these devices if the VCCO_1 and VCCO_2 supplies are also 1.8V.

Power-On Precautions if PROM Supply is Last in Sequence Like SPI Flash PROMs, parallel Flash PROMs typically require some amount of internal initialization time when the supply voltage reaches its minimum value. The PROM supply voltage also connects to the FPGA’s VCCO_2 supply input. In many systems, the PROM supply feeding the FPGA’s VCCO_2 input is valid before the FPGA’s other VCCINT and VCCAUX supplies, and consequently, there is no issue. However, if the PROM supply is last in the sequence, a potential race occurs between the FPGA and the parallel Flash PROM. See

Power-On Precautions if 3.3V Supply is Last in Sequence for a similar description of the issue for SPI Flash PROMs.

Supported Parallel NOR Flash PROM Densities Table 60 indicates the smallest usable parallel Flash PROM to program a single Spartan-3E FPGA. Parallel Flash density is specified in bits but addressed as bytes. The FPGA presents up to 24 address lines during configuration but not all are required for single FPGA applications. Table 60 shows the minimum required number of address lines between the FPGA and parallel Flash PROM. The actual number of address line required depends on the density of the attached parallel Flash PROM. A multiple-FPGA daisy-chained application requires a parallel Flash PROM large enough to contain the sum of the FPGA file sizes. An application can also use a larger-density parallel Flash PROM to hold additional data beyond just FPGA configuration data. For example, the parallel Flash PROM can also contain the application code for a MicroBlaze RISC processor core implemented within the Spartan-3E FPGA. After configuration, the MicroBlaze processor can execute directly from external Flash or can copy the code to other, faster system memory before executing the code.

Table 60: Number of Bits to Program a Spartan-3E FPGA and Smallest Parallel Flash PROM Spartan-3E FPGA

Uncompressed File Sizes (bits)

Smallest Usable Parallel Flash PROM

Minimum Required Address Lines

XC3S100E

581,344

1 Mbit

A[16:0]

XC3S250E

1,353,728

2 Mbit

A[17:0]

XC3S500E

2,270,208

4 Mbit

A[18:0]

XC3S1200E

3,841,184

4 Mbit

A[18:0]

XC3S1600E

5,969,696

8 Mbit

A[19:0]

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 88

Spartan-3E FPGA Family: Functional Description

Compatible Flash Families The Spartan-3E BPI configuration interface operates with a wide variety of x8 or x8/x16 parallel NOR Flash devices. Table 61 provides a few Flash memory families that operate with the Spartan-3E BPI interface. Consult the data sheet for the desired parallel NOR Flash to determine its suitability The basic timing requirements and waveforms are provided in Byte Peripheral Interface (BPI) Configuration Timing (Module 3). Table 61: Compatible Parallel NOR Flash Families Flash Vendor Numonyx

Flash Memory Family M29W, J3D StrataFlash AT29 / AT49

Atmel Spansion

S29

Macronix

MX29

CCLK Frequency In BPI mode, the FPGA’s internal oscillator generates the configuration clock frequency that controls all the interface timing. The FPGA starts configuration at its lowest frequency and increases its frequency for the remainder of the configuration process if so specified in the configuration bitstream. The maximum frequency is specified using the ConfigRate bitstream generator option. Table 62: Maximum ConfigRate Settings for Parallel Flash PROMs (Commercial Temperature Range) Flash Read Access Time

Maximum ConfigRate Setting

250 ns

3

115 ns

6

45 ns

12

Table 62 shows the maximum ConfigRate settings for various typical PROM read access times over the Commercial temperature operating range. See Byte Peripheral Interface (BPI) Configuration Timing (Module 3) and UG332 for more detailed information. Despite using slower ConfigRate settings, BPI mode is equally fast as the other configuration modes. In BPI mode, data is accessed at the ConfigRate frequency and internally serialized with an 8X clock frequency.

Using the BPI Interface after Configuration After the FPGA successfully completes configuration, all pins connected to the parallel Flash PROM are available as user I/Os. If not using the parallel Flash PROM after configuration, drive LDC0 High to disable the PROM’s chip-select input. The remainder of the BPI pins then become available to the FPGA application, including all 24 address lines, the eight data lines, and the LDC2, LDC1, and HDC control pins. DS312 (v4.1) July 19, 2013 Product Specification

Because all the interface pins are user I/Os after configuration, the FPGA application can continue to use the interface pins to communicate with the parallel Flash PROM. Parallel Flash PROMs are available in densities ranging from 1 Mbit up to 128 Mbits and beyond. However, a single Spartan-3E FPGA requires less than 6 Mbits for configuration. If desired, use a larger parallel Flash PROM to contain additional non-volatile application data, such as MicroBlaze processor code, or other user data, such as serial numbers and Ethernet MAC IDs. In such an example, the FPGA configures from parallel Flash PROM. Then using FPGA logic after configuration, a MicroBlaze processor embedded within the FPGA can either execute code directly from parallel Flash PROM or copy the code to external DDR SDRAM and execute from DDR SDRAM. Similarly, the FPGA application can store non-volatile application data within the parallel Flash PROM. The FPGA configuration data is stored starting at either at location 0 or the top of memory (addresses all ones) or at both locations for MultiBoot mode. Store any additional data beginning in other available parallel Flash PROM sectors. Do not mix configuration data and user data in the same sector. Similarly, the parallel Flash PROM interface can be expanded to additional parallel peripherals. The address, data, and LDC1 (OE#) and HDC (WE#) control signals are common to all parallel peripherals. Connect the chip-select input on each additional peripheral to one of the FPGA user I/O pins. If HSWAP = 0 during configuration, the FPGA holds the chip-select line High via an internal pull-up resistor. If HSWAP = 1, connect the select line to +3.3V via an external 4.7 kΩ pull-up resistor to avoid spurious read or write operations. After configuration, drive the select line Low to select the desired peripheral. Refer to the individual peripheral data sheet for specific interface and communication protocol requirements. The FPGA optionally supports a 16-bit peripheral interface by driving the LDC2 (BYTE#) control pin High after configuration. See Precautions Using x8/x16 Flash PROMs for additional information. The FPGA provides up to 24 address lines during configuration, addressing up to 128 Mbits (16 Mbytes). If using a larger parallel PROM, connect the upper address lines to FPGA user I/O. During configuration, the upper address lines will be pulled High if HSWAP = 0. Otherwise, use external pull-up or pull-down resistors on these address lines to define their values during configuration.

Precautions Using x8/x16 Flash PROMs D Most low- to mid-density PROMs are byte-wide (x8)

only. Many higher-density Flash PROMs support both byte-wide (x8) and halfword-wide (x16) data paths and include a mode input called BYTE# that switches between x8 or x16. During configuration, Spartan-3E FPGAs only

www.xilinx.com 89

Spartan-3E FPGA Family: Functional Description support byte-wide data. However, after configuration, the FPGA supports either x8 or x16 modes. In x16 mode, up to eight additional user I/O pins are required for the upper data bits, D[15:8].

Other vendors (AMD, Atmel, Silicon Storage Technology, some STMicroelectronics devices) use a pin-efficient interface but change the function of one pin, called IO15/A-1, depending if the PROM is in x8 or x16 mode. In x8 mode, BYTE# = 0, this pin is the least-significant address line. The A0 address line selects the halfword location. The A-1 address line selects the byte location. When in x16 mode, BYTE# = 1, the IO15/A-1 pin becomes the most-significant data bit, D15 because byte addressing is not required in this mode. Check to see if the Flash PROM has a pin named “IO15/A-1” or “DQ15/A-1”. If so, be careful to connect x8/x16 Flash PROMs correctly, as shown in Table 63. Also, remember that the D[14:8] data connections require FPGA user I/O pins but that the D15 data is already connected for the FPGA’s A0 pin.

Connecting a Spartan-3E FPGA to a x8/x16 Flash PROM is simple, but does require a precaution. Various Flash PROM vendors use slightly different interfaces to support both x8 and x16 modes. Some vendors (Intel, Micron, some STMicroelectronics devices) use a straightforward interface with pin naming that matches the FPGA connections. However, the PROM’s A0 pin is wasted in x16 applications and a separate FPGA user-I/O pin is required for the D15 data line. Fortunately, the FPGA A0 pin is still available as a user I/O after configuration, even though it connects to the Flash PROM. Table 63: FPGA Connections to Flash PROM with IO15/A-1 Pin FPGA Pin

Connection to Flash PROM with IO15/A-1 Pin

x8 Flash PROM Interface After FPGA Configuration

x16 Flash PROM Interface After FPGA Configuration

LDC2

BYTE#

Drive LDC2 Low or leave unconnected and tie PROM BYTE# input to GND

Drive LCD2 High

LDC1

OE#

Active-Low Flash PROM output-enable control

Active-Low Flash PROM output-enable control

LDC0

CS#

Active-Low Flash PROM chip-select control

Active-Low Flash PROM chip-select control

HDC

WE#

Flash PROM write-enable control

Flash PROM write-enable control

A[23:1]

A[n:0]

A[n:0]

A[n:0]

A0

IO15/A-1

IO15/A-1 is the least-significant address input

IO15/A-1 is the most-significant data line, IO15

D[7:0]

IO[7:0]

IO[7:0]

IO[7:0]

User I/O

Upper data lines IO[14:8] not required unless used as x16 Flash interface after configuration

Upper data lines IO[14:8] not required

IO[14:8]

Some x8/x16 Flash PROMs have a long setup time requirement on the BYTE# signal. For the FPGA to configure correctly, the PROM must be in x8 mode with BYTE# = 0 at power-on or when the FPGA’s PROG_B pin is pulsed Low. If required, extend the BYTE# setup time for a 3.3V PROM using an external 680 Ω pull-down resistor on the FPGA’s LDC2 pin or by delaying assertion of the CSI_B select input to the FPGA.

Daisy-Chaining If the application requires multiple FPGAs with different configurations, then configure the FPGAs using a daisy chain, as shown in Figure 59. Use BPI mode (M[2:0] = <0:1:0> or <0:1:1>) for the FPGA connected to the parallel NOR Flash PROM and Slave Parallel mode (M[2:0] = <1:1:0>) for all downstream FPGAs in the daisy-chain. If there are more than two FPGAs in the chain, then last FPGA in the chain can be from any Xilinx FPGA family. However, all intermediate FPGAs located in the

DS312 (v4.1) July 19, 2013 Product Specification

chain between the first and last FPGAs must from either the Spartan-3E or Virtex®-5 FPGA families. After the master FPGA—the FPGA on the left in the diagram—finishes loading its configuration data from the parallel Flash PROM, the master device continues generating addresses to the Flash PROM and asserts its CSO_B output Low, enabling the next FPGA in the daisy-chain. The next FPGA then receives parallel configuration data from the Flash PROM. The master FPGA’s CCLK output synchronizes data capture. If HSWAP = 1, an external 4.7kΩ pull-up resistor must be added on the CSO_B pin. If HSWAP = 0, no external pull-up is necessary. Design Note BPI mode daisy chain software support is available starting in ISE 8.2i. http://www.xilinx.com/support/answers/23061.htm

www.xilinx.com 90

Spartan-3E FPGA Family: Functional Description Also, in a multi-FPGA daisy-chain configuration of more than two devices, all intermediate FPGAs between the first and last devices must be Spartan-3E or Virtex-5 FPGAs. The last FPGA in the chain can be from any Xilinx FPGA family.

BPI Mode Interaction with Right and Bottom Edge Global Clock Inputs Some of the BPI mode configuration pins are shared with global clock inputs along the right and bottom edges of the device (Bank 1 and Bank 2, respectively). These pins are not easily reclaimable for clock inputs after configuration, especially if the FPGA application access the parallel NOR Flash after configuration. Table 64 summarizes the shared pins. Table 64: Shared BPI Configuration Mode and Global Buffer Input Pins Device Edge

Bottom

Right

Global Buffer Input Pin

BPI Mode Configuration Pin

GCLK0

RDWR_B

GCLK2

D2

GCLK3

D1

GCLK12

D7

GCLK13

D6

GCLK14

D4

GCLK15

D3

RHCLK0

A10

RHCLK1

A9

RHCLK2

A8

RHCLK3

A7

RHCLK4

A6

RHCLK5

A5

RHCLK6

A4

RHCLK7

A3

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 91

Spartan-3E FPGA Family: Functional Description

Stepping 0 Limitations when Reprogramming via JTAG if FPGA Set for BPI Configuration

configuration file, then subsequent reconfigurations using the JTAG port will fail. Potential workarounds include setting the mode pins for JTAG configuration (M[2:0] = <1:0:1>) or offsetting the initial memory location in Flash by 0x2000.

The FPGA can always be reprogrammed via the JTAG port, regardless of the mode pin (M[2:0]) settings. However, Stepping 0 devices have a minor limitation. If a Stepping 0 FPGA is set to configure in BPI mode and the FPGA is attached to a parallel memory containing a valid FPGA

Stepping 1 devices fully support JTAG configuration even when the FPGA mode pins are set for BPI mode.

X-Ref Target - Figure 59

CCLK D[7:0] +1.2V

HSWAP

VCCINT VCCO_0 VCCO_1 LDC0 LDC1 HDC LDC2 A[16:0]

Not available in VQ100 package

A

V

I

VCCO_2 D[7:0] A[23:17]

M2 M1 M0

P

DQ[7:0] A[n:0] GND

TMS TCK

VCCAUX TDO

TDI TMS TCK

M2 M1 M0

‘0’

CCLK CSI_B RDWR_B

V

+2.5V

CSO_B INIT_B VCCAUX TDO

TDI TMS TCK PROG_B

DONE 330

GND

V

Spartan-3E FPGA BUSY

+2.5V

TDO

PROG_B

VCCO_2 D[7:0]

‘1’ ‘1’ ‘0’

4.7k

TDI

VCCO_1

Slave Parallel Mode

V

4.7k

2.5V JTAG

VCCO_0

VCCO_1

D

CCLK CSO_B INIT_B

CSI_B RDWR_B

VCCINT VCCO_0

CE# x8 or OE# x8/x16 Flash WE# PROM BYTE#

Spartan-3E BUSY FPGA ‘0’ ‘0’

HSWAP

VCC

DQ[15:7]

BPI Mode ‘0’ ‘1’

VCCO_0

4.7k

P

+1.2V

V

PROG_B Recommend open-drain driver

CSO_B +2.5V

DONE GND

PROG_B TCK TMS DONE INIT_B

DS312-2_50_082009

Figure 59: Daisy-Chaining from BPI Flash Mode

In-System Programming Support

highlighted in the gray boxes in Figure 58 and Figure 59.

I In a production application, the parallel Flash PROM is

usually preprogrammed before it is mounted on the printed circuit board. In-system programming support is available from third-party boundary-scan tool vendors and from some third-party PROM programmers using a socket adapter with attached wires. To gain access to the parallel Flash signals, drive the FPGA’s PROG_B input Low with an open-drain driver. This action places all FPGA I/O pins, including those attached to the parallel Flash, in high-impedance (Hi-Z). If the HSWAP input is Low, the I/Os have pull-up resistors to the VCCO input on their respective I/O bank. The external programming hardware then has direct access to the parallel Flash pins. The programming access points are DS312 (v4.1) July 19, 2013 Product Specification

The FPGA itself can also be used as a parallel Flash PROM programmer during development and test phases. Initially, an FPGA-based programmer is downloaded into the FPGA via JTAG. Then the FPGA performs the Flash PROM programming algorithms and receives programming data from the host via the FPGA’s JTAG interface. See the Embedded System Tools Reference Manual.

Dynamically Loading Multiple Configuration Images Using MultiBoot Option For additional information, refer to the “Reconfiguration and MultiBoot” chapter in UG332.

www.xilinx.com 92

Spartan-3E FPGA Family: Functional Description After the FPGA configures itself using BPI mode from one end of the parallel Flash PROM, then the FPGA can trigger a MultiBoot event and reconfigure itself from the opposite end of the parallel Flash PROM. MultiBoot is only available when using BPI mode and only for applications with a single Spartan-3E FPGA. By default, MultiBoot mode is disabled. To trigger a MultiBoot event, assert a Low pulse lasting at least 300 ns on the MultiBoot Trigger (MBT) input to the STARTUP_SPARTAN3E library primitive. When the MBT signal returns High after the 300 ns or longer pulse, the FPGA automatically reconfigures from the opposite end of the parallel Flash memory.

Figure 60 shows an example usage. At power up, the FPGA loads itself from the attached parallel Flash PROM. In this example, the M0 mode pin is Low so the FPGA starts at address 0 and increments through the Flash PROM memory locations. After the FPGA completes configuration, the application initially loaded into the FPGA performs a board-level or system test using FPGA logic. If the test is successful, the FPGA then triggers a MultiBoot event, causing the FPGA to reconfigure from the opposite end of the Flash PROM memory. This second configuration contains the FPGA application for normal operation. Similarly, the general FPGA application could trigger another MultiBoot event at any time to reload the diagnostics design, and so on.

X-Ref Target - Figure 60

Parallel Flash PROM

Parallel Flash PROM

FFFFFF General FPGA Application

FFFFFF General FPGA Application

STARTUP_SPARTAN3E GSR

User Area

User Area

GTS MBT > 300 ns

CLK

Di agnostics FPGA Application

Reconfigure

Di agnostics FPGA Application

0

0

First Configuration

Second Configuration DS312-2_51_103105

Figure 60: Use MultiBoot to Load Alternate Configuration Images In another potential application, the initial design loaded into the FPGA image contains a “golden” or “fail-safe” configuration image, which then communicates with the outside world and checks for a newer image. If there is a new configuration revision and the new image verifies as good, the “golden” configuration triggers a MultiBoot event to load the new image. When a MultiBoot event is triggered, the FPGA then again drives its configuration pins as described in Table 59. However, the FPGA does not assert the PROG_B pin. The system design must ensure that no other device drives on these same pins during the reconfiguration process. The FPGA’s DONE, LDC[2:0], or HDC pins can temporarily disable any conflicting drivers during reconfiguration. Asserting the PROG_B pin Low overrides the MultiBoot feature and forces the FPGA to reconfigure starting from the end of memory defined by the mode pins, shown in Table 58.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 93

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 61

+1.2V

VCCINT VCCO_0

Slave Parallel Mode

V

‘1’ ‘1’ ‘0’

Intelligent Download Host

- Internal memory - Disk drive - Over network - Over RF link

M2 M1 M0

CSO_B INIT_B

VCCAUX TDO

TDI TMS TCK

- Microcontroller - Processor - Tester - Computer

V

Spartan-3E FPGA

D[7:0] BUSY CSI_B RDWR_B CCLK

GND

V

4.7

Configuration Memory Source

VCC D[7:0] BUSY SELECT READ/WRITE CLOCK PROG_B DONE INIT_B

VCCO_2

VCCO_0

+2.5V

+2.5V

PROG_B

DONE GND

4.7k

HSWAP

330

P

PROG_B Recommend open-drain driver

+2.5V JTAG TDI

TMS TCK DS312-2_52_082009

TDO

Figure 61: Slave Parallel Configuration Mode

Slave Parallel Mode For additional information, refer to the “Slave Parallel (SelectMAP) Mode” chapter in UG332. In Slave Parallel mode (M[2:0] = <1:1:0>), an external host, such as a microprocessor or microcontroller, writes byte-wide configuration data into the FPGA, using a typical peripheral interface as shown in Figure 61. The external download host starts the configuration process by pulsing PROG_B and monitoring that the INIT_B pin goes High, indicating that the FPGA is ready to receive its first data. The host asserts the active-Low chip-select signal (CSI_B) and the active-Low Write signal (RDWR_B). The host then continues supplying data and clock signals until either the FPGA’s DONE pin goes High, indicating a successful configuration, or until the FPGA’s INIT_B pin goes Low, indicating a configuration error. DS312 (v4.1) July 19, 2013 Product Specification

The FPGA captures data on the rising CCLK edge. If the CCLK frequency exceeds 50 MHz, then the host must also monitor the FPGA’s BUSY output. If the FPGA asserts BUSY High, the host must hold the data for an additional clock cycle, until BUSY returns Low. If the CCLK frequency is 50 MHz or below, the BUSY pin may be ignored but actively drives during configuration. The configuration process requires more clock cycles than indicated from the configuration file size. Additional clocks are required during the FPGA’s start-up sequence, especially if the FPGA is programmed to wait for selected Digital Clock Managers (DCMs) to lock to their respective clock inputs (see Start-Up, page 106). If the Slave Parallel interface is only used to configure the FPGA, never to read data back, then the RDWR_B signal

www.xilinx.com 94

Spartan-3E FPGA Family: Functional Description can also be eliminated from the interface. However, RDWR_B must remain Low during configuration.

The Persist option will maintain A20-A23 as configuration pins although they are not used in SelectMAP mode.

After configuration, all of the interface pins except DONE and PROG_B are available as user I/Os. Alternatively, the bidirectional SelectMAP configuration interface is available after configuration. To continue using SelectMAP mode, set the Persist bitstream generator option to Yes. The external host can then read and verify configuration data.

The Slave Parallel mode is also used with BPI mode to create multi-FPGA daisy-chains. The lead FPGA is set for BPI mode configuration; all the downstream daisy-chain FPGAs are set for Slave Parallel configuration, as highlighted in Figure 59.

Table 65: Slave Parallel Mode Connections Pin Name

FPGA Direction

Description

During Configuration

After Configuration

HSWAP

Input

User I/O Pull-Up Control. When Low during configuration, enables pull-up resistors in all I/O pins to respective I/O bank VCCO input. 0: Pull-ups during configuration 1: No pull-ups

Drive at valid logic level throughout configuration.

User I/O

M[2:0]

Input

Mode Select. Selects the FPGA configuration mode. See Design Considerations for the HSWAP, M[2:0], and VS[2:0] Pins.

M2 = 1, M1 = 1, M0 = 0 Sampled when INIT_B goes High.

User I/O

D[7:0]

Input

Data Input.

Byte-wide data provided by host. FPGA captures data on rising CCLK edge.

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

BUSY

Output

Busy Indicator.

If CCLK frequency is < 50 MHz, this pin may be ignored. When High, indicates that the FPGA is not ready to receive additional configuration data. Host must hold data an additional clock cycle.

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

CSI_B

Input

Chip Select Input. Active Low.

Must be Low throughout configuration.

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

RDWR_B

Input

Read/Write Control. Active Low write enable.

Must be Low throughout configuration.

User I/O. If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

CCLK

Input

Configuration Clock. If CCLK PCB External clock. trace is long or has multiple connections, terminate this output to maintain signal integrity. See CCLK Design Considerations.

CSO_B

Output

DS312 (v4.1) July 19, 2013 Product Specification

Chip Select Output. Active Low.

User I/O If bitstream option Persist=Yes, becomes part of SelectMap parallel peripheral interface.

Not used in single FPGA User I/O applications. In a daisy-chain configuration, this pin connects to the CSI_B pin of the next FPGA in the chain. Actively drives.

www.xilinx.com 95

Spartan-3E FPGA Family: Functional Description Table 65: Slave Parallel Mode Connections (Cont’d) Pin Name

FPGA Direction

Description

INIT_B

Open-drain bidirectional I/O

Initialization Indicator. Active Low. Goes Low at the start of configuration during the Initialization memory clearing process. Released at the end of memory clearing, when mode select pins are sampled. In daisy-chain applications, this signal requires an external 4.7 kΩ pull-up resistor to VCCO_2.

DONE

Open-drain bidirectional I/O

FPGA Configuration Done. Low Low indicates that the FPGA is not during configuration. Goes High yet configured. when FPGA successfully completes configuration. Requires external 330 Ω pull-up resistor to 2.5V.

Pulled High via external pull-up. When High, indicates that the FPGA successfully configured.

Program FPGA. Active Low. When Must be High to allow asserted Low for 500 ns or longer, configuration to start. forces the FPGA to restart its configuration process by clearing configuration memory and resetting the DONE and INIT_B pins once PROG_B returns High. Recommend external 4.7 kΩ pull-up resistor to 2.5V. Internal pull-up value may be weaker (see Table 78). If driving externally with a 3.3V output, use an open-drain or open-collector driver or use a current limiting series resistor.

Drive PROG_B Low and release to reprogram FPGA.

PROG_B

Input

During Configuration Active during configuration. If CRC error detected during configuration, FPGA drives INIT_B Low.

After Configuration User I/O. If unused in the application, drive INIT_B High.

Voltage Compatibility V Most Slave Parallel interface signals are within the

FPGA’s I/O Bank 2, supplied by the VCCO_2 supply input. The VCCO_2 voltage can be 1.8V, 2.5V, or 3.3V to match the requirements of the external host, ideally 2.5V. Using 1.8V or 3.3V requires additional design considerations as the DONE and PROG_B pins are powered by the FPGA’s 2.5V VCCAUX supply. See XAPP453: The 3.3V Configuration of Spartan-3 FPGAs for additional information.

Daisy-Chaining If the application requires multiple FPGAs with different configurations, then configure the FPGAs using a daisy chain. Use Slave Parallel mode (M[2:0] = <1:1:0>) for all FPGAs in the daisy-chain. The schematic in Figure 62 is optimized for FPGA downloading and does not support the SelectMAP read interface. The FPGA’s RDWR_B pin must be Low during configuration. After the lead FPGA is filled with its configuration data, the lead FPGA enables the next FPGA in the daisy-chain by asserting is chip-select output, CSO_B.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 96

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 62

D[7:0] CCLK +1.2V

VCCINT VCCO_0 VCCO_1 LDC0 LDC1 HDC LDC2

Slave Parallel Mode

Configuration Memory Source

• Internal memory • Disk drive • Over network • Over RF link

VCC DATA[7:0] BUSY SELECT READ/WRITE CLOCK PROG_B DONE INIT_B GND

• Microcontroller • Processor • Tester

‘1’ ‘1’ ‘0’

‘0’

VCCO_2 M2 M1 M0

Spartan-3E FPGA D[7:0]

BUSY CSI_B RDWR_B CCLK

V

Slave Parallel Mode

V

‘1’ ‘1’ ‘0’

CSO_B INIT_B

VCCAUX TDO

TDI TMS TCK

‘0’

VCCINT VCCO_0 VCCO_1 LDC0 LDC1 HDC LDC2 VCCO_2

M2 M1 M0

DONE

VCCO_1

V

Spartan-3E

VCCAUX TDO

TDI TMS TCK PROG_B

GND

VCCO_0

D[7:0] FPGA BUSY CSI_B CSO_B INIT_B RDWR_B CCLK

+2.5V

+2.5V

PROG_B

HSWAP

VCCO_1

330Ω

V Intelligent Download Host

P

VCCO_0

4.7kΩ

HSWAP

4.7kΩ

P

+1.2V

PROG_B Recommend 2.5V open-drain driver JTAG TDI TMS TCK TDO

CSO_B

+2.5V

DONE GND

PROG_B DONE INIT_B TMS TCK DS312-2_53_082009

Figure 62: Daisy-Chaining using Slave Parallel Mode

Slave Serial Mode For additional information, refer to the “Slave Serial Mode” chapter in UG332. In Slave Serial mode (M[2:0] = <1:1:1>), an external host such as a microprocessor or microcontroller writes serial configuration data into the FPGA, using the synchronous serial interface shown in Figure 63. The serial configuration data is presented on the FPGA’s DIN input pin with sufficient setup time before each rising edge of the externally generated CCLK clock input.

DS312 (v4.1) July 19, 2013 Product Specification

The intelligent host starts the configuration process by pulsing PROG_B and monitoring that the INIT_B pin goes High, indicating that the FPGA is ready to receive its first data. The host then continues supplying data and clock signals until either the DONE pin goes High, indicating a successful configuration, or until the INIT_B pin goes Low, indicating a configuration error. The configuration process requires more clock cycles than indicated from the configuration file size. Additional clocks are required during the FPGA’s start-up sequence, especially if the FPGA is programmed to wait for selected Digital Clock Managers (DCMs) to lock to their respective clock inputs (see Start-Up, page 106).

www.xilinx.com 97

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 63

+1.2V

HSWAP

VCCINT VCCO_0 VCCO_2

Slave Serial Mode

• Internal memory • Disk drive • Over network • Over RF link

VCC CLOCK SERIAL_OUT PROG_B DONE INIT_B

V M2 M1 M0

Spartan-3E FPGA

CCLK DIN

DOUT INIT_B VCCAUX TDO

TDI TMS TCK

GND • Microcontroller • Processor • Tester • Computer

+2.5V

+2.5V

PROG_B

DONE GND

4.7k

Configuration Memory Source

‘1’ ‘1’ ‘1’

V

V

330

Intelligent Download Host

VCCO_0

4.7k

P

PROG_B

Recommend open-drain driver +2.5V JTAG TDI TMS TCK TDO

DS312-2_54_082009

Figure 63: Slave Serial Configuration The mode select pins, M[2:0], are sampled when the FPGA’s INIT_B output goes High and must be at defined logic levels during this time. After configuration, when the FPGA’s DONE output goes High, the mode pins are available as full-featured user-I/O pins. P Similarly, the FPGA’s HSWAP pin must be Low to

enable pull-up resistors on all user-I/O pins or High to disable the pull-up resistors. The HSWAP control must remain at a constant logic level throughout FPGA configuration. After configuration, when the FPGA’s DONE output goes High, the HSWAP pin is available as full-featured user-I/O pin and is powered by the VCCO_0 supply.

DS312 (v4.1) July 19, 2013 Product Specification

Voltage Compatibility V Most Slave Serial interface signals are within the

FPGA’s I/O Bank 2, supplied by the VCCO_2 supply input. The VCCO_2 voltage can be 3.3V, 2.5V, or 1.8V to match the requirements of the external host, ideally 2.5V. Using 3.3V or 1.8V requires additional design considerations as the DONE and PROG_B pins are powered by the FPGA’s 2.5V VCCAUX supply. See XAPP453: The 3.3V Configuration of Spartan-3 FPGAs for additional information.

Daisy-Chaining If the application requires multiple FPGAs with different configurations, then configure the FPGAs using a daisy chain, as shown in Figure 64. Use Slave Serial mode (M[2:0] = <1:1:1>) for all FPGAs in the daisy-chain. After the lead FPGA is filled with its configuration data, the lead

www.xilinx.com 98

Spartan-3E FPGA Family: Functional Description FPGA passes configuration data via its DOUT output pin to the next FPGA on the falling CCLK edge. Table 66: Slave Serial Mode Connections FPGA Direction

Description

HSWAP

Pin Name

Input

User I/O Pull-Up Control. When Low during configuration, enables pull-up resistors in all I/O pins to respective I/O bank VCCO input. 0: Pull-up during configuration 1: No pull-ups

Drive at valid logic level throughout configuration.

User I/O

M[2:0]

Input

Mode Select. Selects the FPGA configuration mode. See Design Considerations for the HSWAP, M[2:0], and VS[2:0] Pins.

M2 = 1, M1 = 1, M0 = 1 Sampled when INIT_B goes High.

User I/O

DIN

Input

Data Input.

Serial data provided by host. FPGA captures data on rising CCLK edge.

User I/O

CCLK

Input

Configuration Clock. If CCLK PCB trace is long or has multiple connections, terminate this output to maintain signal integrity. See CCLK Design Considerations.

External clock.

User I/O

INIT_B

Open-drain bidirectional I/O

Initialization Indicator. Active Low. Goes Low at start of configuration during Initialization memory clearing process. Released at end of memory clearing, when mode select pins are sampled. In daisy-chain applications, this signal requires an external 4.7 kΩ pull-up resistor to VCCO_2.

Active during configuration. If CRC error detected during configuration, FPGA drives INIT_B Low.

User I/O. If unused in the application, drive INIT_B High.

DONE

Open-drain bidirectional I/O

FPGA Configuration Done. Low Low indicates that the FPGA is not during configuration. Goes High yet configured. when FPGA successfully completes configuration. Requires external 330 Ω pull-up resistor to 2.5V.

Pulled High via external pull-up. When High, indicates that the FPGA successfully configured.

Program FPGA. Active Low. Must be High to allow When asserted Low for 500 ns or configuration to start. longer, forces the FPGA to restart its configuration process by clearing configuration memory and resetting the DONE and INIT_B pins once PROG_B returns High. Recommend external 4.7 kΩ pull-up resistor to 2.5V. Internal pull-up value may be weaker (see Table 78). If driving externally with a 3.3V output, use an open-drain or open-collector driver or use a current limiting series resistor.

Drive PROG_B Low and release to reprogram FPGA.

PROG_B

Input

DS312 (v4.1) July 19, 2013 Product Specification

During Configuration

After Configuration

www.xilinx.com 99

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 64

CCLK +1.2V

HSWAP

VCCINT VCCO_0 VCCO_2

Slave Serial Mode

• Internal memory • Disk drive • Over network • Over RF link

GND

• Microcontroller • Processor • Tester • Computer

M2 M1 M0

Spartan-3E FPGA

CCLK DIN

‘1’ ‘1’ ‘1’

VCCAUX TDO

VCCO_2

M2 M1 M0

Spartan-3E FPGA DOUT INIT_B

+2.5V

+2.5V

PROG_B

VCCO_0

VCCO_2

CCLK DIN

DOUT INIT_B

TDI TMS TCK

VCCINT VCCO_0

Slave Serial Mode

V

DONE

VCCAUX TDO

TDI TMS TCK PROG_B

330 Ω

Configuration Memory Source

VCC CLOCK SERIAL_OUT PROG_B DONE INIT_B

‘1’ ‘1’ ‘1’

V

HSWAP

GND

4.7k Ω

Intelligent V Download Host

P

VCCO_0

4.7kΩ

P

+1.2V

DOUT +2.5V

DONE GND

PROG_B Recommend open-drain driver +2.5V JTAG TDI TMS TCK TDO

PROG_B DONE INIT_B

TMS TCK DS312-2_55_082009

Figure 64: Daisy-Chaining using Slave Serial Mode

JTAG Mode For additional information, refer to the “JTAG Configuration Mode and Boundary-Scan” chapter in UG332. The Spartan-3E FPGA has a dedicated four-wire IEEE 1149.1/1532 JTAG port that is always available any time the FPGA is powered and regardless of the mode pin settings. However, when the FPGA mode pins are set for JTAG mode (M[2:0] = <1:0:1>), the FPGA waits to be configured via the JTAG port after a power-on event or when PROG_B is asserted. Selecting the JTAG mode simply disables the other configuration modes. No other pins are required as part of the configuration interface.

The FPGA bitstream may be corrupted and the DONE pin may go High. The following Answer Record contains additional information. http://www.xilinx.com/support/answers/22255.htm

Figure 65 illustrates a JTAG-only configuration interface. The JTAG interface is easily cascaded to any number of FPGAs by connecting the TDO output of one device to the TDI input of the next device in the chain. The TDO output of the last device in the chain loops back to the port connector. Design Note If using software versions prior to ISE 9.1.01i, avoid configuring the FPGA using JTAG if... •

the mode pins are set for a Master mode



the attached Master mode PROM contains a valid FPGA configuration bitstream.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 100

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 65

+1.2V

+1.2V

P

HSWAP

JTAG Mode ‘1’ ‘0’ ‘1’

VCCINT VCCO_0

VCCO_0

VCCO_2

VCCO_2

VCCAUX TDO

TDI TMS TCK PROG_B

HSWAP

JTAG Mode

Spartan-3E FPGA

M2 M1 M0

P

‘1’ ‘0’ ‘1’

M2 M1 M0

VCCO_0

VCCO_2

VCCO_2

Spartan-3E FPGA

VCCAUX TDO

+2.5V TDI TMS TCK PROG_B

DONE

+2.5V

DONE GND

GND

+2.5V JTAG TDI TMS TCK TDO

VCCINT VCCO_0

TMS TCK DS312-2_56_082009

Figure 65: JTAG Configuration Mode

Voltage Compatibility

JTAG Device ID

The 2.5V VCCAUX supply powers the JTAG interface. All of the user I/Os are separately powered by their respective VCCO_# supplies.

Each Spartan-3E FPGA array type has a 32-bit device-specific JTAG device identifier as shown in Table 67. The lower 28 bits represent the device vendor (Xilinx) and device identifer. The upper four bits, ignored by most tools, represent the revision level of the silicon mounted on the printed circuit board. Table 67 associates the revision code with a specific stepping level.

When connecting the Spartan-3E JTAG port to a 3.3V interface, the JTAG input pins must be current-limited to 10 mA or less using series resistors. Similarly, the TDO pin is a CMOS output powered from +2.5V. The TDO output can directly drive a 3.3V input but with reduced noise immunity. See XAPP453: The 3.3V Configuration of Spartan-3 FPGAs for additional information. Table 67: Spartan-3E JTAG Device Identifiers

Step 0

Step 1

28-Bit Vendor/Device Identifier

XC3S100E

0x0

0x1

0x1C 10 093

XC3S250E

0x0

0x1

0x1C 1A 093

XC3S500E

0x0 0x2

0x4

0x1C 22 093

XC3S1200E

0x0 0x1

0x2

0x1C 2E 093

XC3S1600E

0x0 0x1

0x2

0x1C 3A 093

Spartan-3E FPGA

4-Bit Revision Code

DS312 (v4.1) July 19, 2013 Product Specification

JTAG User ID The Spartan-3E JTAG interface also provides the option to store a 32-bit User ID, loaded during configuration. The User ID value is specified via the UserID configuration bitstream option, shown in Table 69, page 108.

Using JTAG Interface to Communicate to a Configured FPGA Design After the FPGA is configured, using any of the available modes, the JTAG interface offers a possible communications channel to internal FPGA logic. The BSCAN_SPARTAN3 design primitive provides two private JTAG instructions to create an internal boundary scan chain.

www.xilinx.com 101

Spartan-3E FPGA Family: Functional Description

Maximum Bitstream Size for Daisy-Chains The maximum bitstream length supported by Spartan-3E FPGAs in serial daisy-chains is 4,294,967,264 bits (4 Gbits), roughly equivalent to a daisy-chain with 720 XC3S1600E FPGAs. This is a limit only for serial daisy-chains where configuration data is passed via the FPGA’s DOUT pin. There is no such limit for JTAG chains.

The FPGA configuration sequence can also be initiated by asserting PROG_B. Once released, the FPGA begins clearing its internal configuration memory, and progresses through the remainder of the configuration process.

Configuration Sequence For additional information including I/O behavior before and during configuration, refer to the “Sequence of Events” chapter in UG332. The Spartan-3E configuration process is three-stage process that begins after the FPGA powers on (a POR event) or after the PROG_B input is asserted. Power-On Reset (POR) occurs after the VCCINT, VCCAUX, and the VCCO Bank 2 supplies reach their respective input threshold levels. After either a POR or PROG_B event, the three-stage configuration process begins. 1. The FPGA clears (initializes) the internal configuration memory. 2. Configuration data is loaded into the internal memory. 3. The user-application is activated by a start-up process. Figure 66 is a generalized block diagram of the Spartan-3E configuration logic, showing the interaction of different device inputs and Bitstream Generator (BitGen) options. A flow diagram for the configuration sequence of the Serial and Parallel modes appears in Figure 66. Figure 67 shows the Boundary-Scan or JTAG configuration sequence.

Initialization Configuration automatically begins after power-on or after asserting the FPGA PROG_B pin, unless delayed using the FPGA’s INIT_B pin. The FPGA holds the open-drain INIT_B signal Low while it clears its internal configuration memory. Externally holding the INIT_B pin Low forces the configuration sequencer to wait until INIT_B again goes High. The FPGA signals when the memory-clearing phase is complete by releasing the open-drain INIT_B pin, allowing the pin to go High via the external pull-up resistor to VCCO_2.

Loading Configuration Data After initialization, configuration data is written to the FPGA’s internal memory. The FPGA holds the Global Set/Reset (GSR) signal active throughout configuration, holding all FPGA flip-flops in a reset state. The FPGA signals when the entire configuration process completes by releasing the DONE pin, allowing it to go High.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 102

DS312 (v4.1) July 19, 2013 Product Specification

0

TCK

M2

M1

1

Glitch Filter

VCCAUXT

VCCINTT

VCCO2T

CCLK

PROG_B

VCCAUX

VCCINT

VCCO_2

Internal Oscillator

ConfigRate 0

1

POWER_GOOD

= Design Attribute

Option

Power On Reset (POR)

= Bitstream Generator (BitGen) Option

Option

LOCKED

DONE

JTAG_CLOCK

WAIT

All DCMs

RESET

*

ERROR

StartupClk

USER

USER

Configuration Error Detection (CRC Checker)

ENABLE

USER_CLOCK

CRC

DONE

Load application data into CMOS configuration latches

ENABLE

CONFIGURATION

INTERNAL_CONFIGURATION_CLOCK

RESET

CLEARING_MEMORY

Clear internal CMOS configuration latches

ENABLE

INITIALIZATION

STARTUP_WAIT=TRUE

DCM in User Application

* *

DONE

*

WAIT DonePipe

GWE

GSR

GTS

GWE_cycle

GTS_cycle

DONE_cycle

EN

EN

These connections are available via the STARTUP_SPARTAN3E library primitive.

RESET

GSR_IN

GTS_IN

ENABLE

Enable application logic and I/O pins

DCMs_LOCKED LCK_cycle

STARTUP

DriveDone

INIT_B

Disable write operations to storage elements

Hold all storage elements reset

Force all I/Os Hi-Z

DONE

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 66

DS312-2_57_102605

Figure 66: Generalized Spartan-3E FPGA Configuration Logic Block Diagram

www.xilinx.com

103

Spartan-3E FPGA Family: Functional Description

Set PROG_B Low after Power-On

Power-On

VCCINT >1V and VCCAUX > 2V and VCCO Bank 2 > 1V

No

Yes Yes

Clear configuration memory

PROG_B = Low

No

No

INIT_ B = High?

Yes

Sample mode pins

M[2:0] and VS[2:0] pins are sampled on INIT_B rising edge

Load configuration data frames

CRC correct?

No

INIT_B goes Low. Abort Start-Up

Yes Start-Up sequence

DONE pin goes High, signaling end of configuration

User mode

No

Reconfigure?

Yes

DS312-2_58_051706

Figure 66: General Configuration Process

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 104

Spartan-3E FPGA Family: Functional Description

X-Ref Target - Figure 67

Set PROG_B Low after Power-On

Power-On

VCCINT >1V and VCCAUX > 2V and VCCO Bank 2 > 1V Load JPROG instruction

No

Yes Clear configuration memory

Yes

PROG_B = Low

No No

INIT_B = High?

Yes Sample mode pins (JTAG port becomes available)

Load CFG_IN instruction

Load configuration data frames

CRC correct?

No

INIT_B goes Low. Abort Start-Up

Yes Synchronous TAP reset (Clock five 1's on TMS)

Load JSTART instruction

Start-Up sequence

User mode

Yes

Reconfigure?

No DS312-2_59_051706

Figure 67: Boundary-Scan Configuration Flow Diagram

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 105

Spartan-3E FPGA Family: Functional Description

Start-Up At the end of configuration, the FPGA automatically pulses the Global Set/Reset (GSR) signal, placing all flip-flops in a known state. After configuration completes, the FPGA switches over to the user application loaded into the FPGA. The sequence and timing of how the FPGA switches over is programmable as is the clock source controlling the sequence. The default start-up sequence appears in Figure 68, where the Global Three-State signal (GTS) is released one clock cycle after DONE goes High. This sequence allows the DONE signal to enable or disable any external logic used during configuration before the user application in the FPGA starts driving output signals. One clock cycle later, the Global Write Enable (GWE) signal is released. This allows signals to propagate within the FPGA before any clocked storage elements such as flip-flops and block ROM are enabled. X-Ref Target - Figure 68

Default Cycles

become user I/Os. Like all user-I/O pins, GTS controls when the dual-purpose pins can drive out. The relative timing of configuration events is programmed via the Bitstream Generator (BitGen) options in the Xilinx development software. For example, the GTS and GWE events can be programmed to wait for all the DONE pins to High on all the devices in a multiple-FPGA daisy-chain, forcing the FPGAs to start synchronously. Similarly, the start-up sequence can be paused at any stage, waiting for selected DCMs to lock to their respective input clock signals. See also Stabilizing DCM Clocks Before User Mode. By default, the start-up sequence is synchronized to CCLK. Alternatively, the start-up sequence can be synchronized to a user-specified clock from within the FPGA application using the STARTUP_SPARTAN3E library primitive and by setting the StartupClk bitstream generator option. The FPGA application can optionally assert the GSR and GTS signals via the STARTUP_SPARTAN3E primitive. For JTAG configuration, the start-up sequence can be synchronized to the TCK clock input.

Start-Up Clock

Phase

0

1

2

3

4

5

6 7

DONE

GTS

GWE

Sync-to-DONE Start-Up Clock

Phase

0

1

2

3

4

5

6 7

DONE High

DONE

GTS

GWE DS312-2_60_022305

Figure 68: Default Start-Up Sequence The function of the dual-purpose I/O pins, such as M[2:0], VS[2:0], HSWAP, and A[23:0], also changes when the DONE pin goes High. When DONE is High, these pins

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 106

Spartan-3E FPGA Family: Functional Description

Readback FPGA configuration data can be read back using either the Slave Parallel or JTAG mode. This function is disabled if the Bitstream Generator Security option is set to either Level1 or Level2.

Table 68: Readback Support in Spartan-3E FPGAs Temperature Range Speed Grade

Commercial -4

-5

-4

No

Yes

Yes

Along with the configuration data, it is possible to read back the contents of all registers and distributed RAM.

Block RAM Readback

To synchronously control when register values are captured for readback, use the CAPTURE_SPARTAN3 library primitive, which applies for both Spartan-3 and Spartan-3E FPGA families.

General Readback (registers, distributed RAM)

All Spartan-3E FPGAs

The Readback feature is available in most Spartan-3E FPGA product options, as indicated in Table 68. The Readback feature is not available in the XC3S1200E and XC3S1600E FPGAs when using the -4 speed grade in the Commercial temperature grade. Similarly, block RAM Readback support is not available in the -4 speed grade, Commercial temperature devices. If Readback is required in an XC3S1200E or XC3S1600E FPGA, or if block RAM Readback is required on any Spartan-3E FPGA, upgrade to either the Industrial temperature grade version or the -5 speed grade.

Industrial

XC3S100E

Yes

Yes

Yes

XC3S250E

Yes

Yes

Yes

XC3S500E

Yes

Yes

Yes

XC3S1200E

No

Yes

Yes

XC3S1600E

No

Yes

Yes

The Xilinx iMPACT programming software uses the Readback feature for its optional Verify and Readback operations. The Xilinx ChipScope™ software presently does not use Readback but may in future updates.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 107

Spartan-3E FPGA Family: Functional Description

Bitstream Generator (BitGen) Options For additional information, refer to the “Configuration Bitstream Generator (BitGen) Settings” chapter in UG332.

values are specified when creating the bitstream image with the Bitstream Generator (BitGen) software.

Various Spartan-3E FPGA functions are controlled by specific bits in the configuration bitstream image. These

Table 69 provides a list of all BitGen options for Spartan-3E FPGAs.

Table 69: Spartan-3E FPGA Bitstream Generator (BitGen) Options Option Name

Pins/Function Affected

ConfigRate

CCLK, Configuration

StartupClk

Configuration, Startup

UnusedPin

Unused I/O Pins

Values (default)

Description

Sets the approximate frequency, in MHz, of the internal oscillator using for Master 1, 3, 6, 12, 25, 50 Serial, SPI, and BPI configuration modes. The internal oscillator powers up at its lowest frequency, and the new setting is loaded as part of the configuration bitstream. The software default value is 1 (~1.5 MHz) starting with ISE 8.1, Service Pack 1. Cclk

Default. The CCLK signal (internally or externally generated) controls the startup sequence when the FPGA transitions from configuration mode to the user mode. See Start-Up.

UserClk

A clock signal from within the FPGA application controls the startup sequence when the FPGA transitions from configuration mode to the user mode. See Start-Up. The FPGA application supplies the user clock on the CLK pin on the STARTUP_SPARTAN3E primitive.

Jtag

The JTAG TCK input controls the startup sequence when the FPGA transitions from the configuration mode to the user mode. See Start-Up.

Pulldown

Default. All unused I/O pins and input-only pins have a pull-down resistor to GND.

Pullup

All unused I/O pins and input-only pins have a pull-up resistor to the VCCO_# supply for its associated I/O bank.

Pullnone

All unused I/O pins and input-only pins are left floating (Hi-Z, high-impedance, three-state). Use external pull-up or pull-down resistors or logic to apply a valid signal level.

DONE_cycle

DONE pin, Configuration Startup

1, 2, 3, 4, 5, 6

Selects the Configuration Startup phase that activates the FPGA’s DONE pin. See Start-Up.

GWE_cycle

All flip-flops, LUT RAMs, and SRL16 shift registers, Block RAM, Configuration Startup

1, 2, 3, 4, 5, 6

Selects the Configuration Startup phase that asserts the internal write-enable signal to all flip-flops, LUT RAMs and shift registers (SRL16). It also enables block RAM read and write operations. See Start-Up.

Done

Waits for the DONE pin input to go High before asserting the internal write-enable signal to all flip-flops, LUT RAMs and shift registers (SRL16). Block RAM read and write operations are enabled at this time.

Keep

Retains the current GWE_cycle setting for partial reconfiguration applications.

GTS_cycle

LCK_cycle

DonePin

All I/O pins, Configuration

DCMs, Configuration Startup

DONE pin

1, 2, 3, 4, 5, 6

Selects the Configuration Startup phase that releases the internal three-state control, holding all I/O buffers in high-impedance (Hi-Z). Output buffers actively drive, if so configured, after this point. See Start-Up.

Done

Waits for the DONE pin input to go High before releasing the internal three-state control, holding all I/O buffers in high-impedance (Hi-Z). Output buffers actively drive, if so configured, after this point.

Keep

Retains the current GTS_cycle setting for partial reconfiguration applications.

NoWait 0, 1, 2, 3, 4, 5, 6

Pullup Pullnone

DS312 (v4.1) July 19, 2013 Product Specification

The FPGA does not wait for selected DCMs to lock before completing configuration. If one or more DCMs in the design have the STARTUP_WAIT attribute set to TRUE, the FPGA waits for such DCMs to acquire their respective input clock and assert their LOCKED output. This setting selects the Configuration Startup phase where the FPGA waits for the DCMs to lock. Internally connects a pull-up resistor between DONE pin and VCCAUX. An external 330 Ω pull-up resistor to VCCAUX is still recommended. No internal pull-up resistor on DONE pin. An external 330 Ω pull-up resistor to VCCAUX is required.

www.xilinx.com 108

Spartan-3E FPGA Family: Functional Description Table 69: Spartan-3E FPGA Bitstream Generator (BitGen) Options (Cont’d) Option Name DriveDone

DonePipe

ProgPin

Pins/Function Affected

Values (default)

DONE pin

No

When configuration completes, the DONE pin stops driving Low and relies on an external 330 Ω pull-up resistor to VCCAUX for a valid logic High.

Yes

When configuration completes, the DONE pin actively drives High. When using this option, an external pull-up resistor is no longer required. Only one device in an FPGA daisy-chain should use this setting.

No

The input path from DONE pin input back to the Startup sequencer is not pipelined.

Yes

This option adds a pipeline register stage between the DONE pin input and the Startup sequencer. Used for high-speed daisy-chain configurations when DONE cannot rise in a single CCLK cycle. Releases GWE and GTS signals on the first rising edge of StartupClk after the DONE pin input goes High.

Pullup

Internally connects a pull-up resistor or between PROG_B pin and VCCAUX. An external 4.7 kΩ pull-up resistor to VCCAUX is still recommended since the internal pull-up value may be weaker (see Table 78).

DONE pin

PROG_B pin

Pullnone TckPin

TdiPin

TdoPin

TmsPin

JTAG TCK pin

JTAG TDI pin

JTAG TDO pin

JTAG TMS pin

UserID

JTAG User ID register

Security

JTAG, SelectMAP, Readback, Partial reconfiguration

CRC

Persist

Configuration

SelectMAP interface pins, BPI mode, Slave mode, Configuration

DS312 (v4.1) July 19, 2013 Product Specification

Description

No internal pull-up resistor on PROG_B pin. An external 4.7 kΩ pull-up resistor to VCCAUX is required.

Pullup

Internally connects a pull-up resistor between JTAG TCK pin and VCCAUX.

Pulldown

Internally connects a pull-down resistor between JTAG TCK pin and GND.

Pullnone

No internal pull-up resistor on JTAG TCK pin.

Pullup

Internally connects a pull-up resistor between JTAG TDI pin and VCCAUX.

Pulldown

Internally connects a pull-down resistor between JTAG TDI pin and GND.

Pullnone

No internal pull-up resistor on JTAG TDI pin.

Pullup

Internally connects a pull-up resistor between JTAG TDO pin and VCCAUX.

Pulldown

Internally connects a pull-down resistor between JTAG TDO pin and GND.

Pullnone

No internal pull-up resistor on JTAG TDO pin.

Pullup

Internally connects a pull-up resistor between JTAG TMS pin and VCCAUX.

Pulldown

Internally connects a pull-down resistor between JTAG TMS pin and GND.

Pullnone

No internal pull-up resistor on JTAG TMS pin.

User string The 32-bit JTAG User ID register value is loaded during configuration. The default value is all ones, 0xFFFF_FFFF hexadecimal. To specify another value, enter an 8-character hexadecimal value. None

Readback and limited partial reconfiguration are available via the JTAG port or via the SelectMAP interface, if the Persist option is set to Yes.

Level1

Readback function is disabled. Limited partial reconfiguration is still available via the JTAG port or via the SelectMAP interface, if the Persist option is set to Yes.

Level2

Readback function is disabled. Limited partial reconfiguration is disabled.

Enable

Default. Enable CRC checking on the FPGA bitstream. If error detected, FPGA asserts INIT_B Low and DONE pin stays Low.

Disable

Turn off CRC checking.

No

All BPI and Slave mode configuration pins are available as user-I/O after configuration.

Yes

This option is required for Readback and partial reconfiguration using the SelectMAP interface. The SelectMAP interface pins (see Slave Parallel Mode) are reserved after configuration and are not available as user-I/O.

www.xilinx.com 109

Spartan-3E FPGA Family: Functional Description

Powering Spartan-3E FPGAs For additional information, refer to the “Powering Spartan-3 Generation FPGAs” chapter in UG331.

Voltage Supplies

supply inputs for internal logic functions, VCCINT and VCCAUX. Each of the four I/O banks has a separate VCCO supply input that powers the output buffers within the associated I/O bank. All of the VCCO connections to a specific I/O bank must be connected and must connect to the same voltage.

Like Spartan-3 FPGAs, Spartan-3E FPGAs have multiple voltage supply inputs, as shown in Table 70. There are two Table 70: Spartan-3E Voltage Supplies Supply Input

Description

Nominal Supply Voltage

VCCINT

Internal core supply voltage. Supplies all internal logic functions, such as CLBs, block RAM, and multipliers. Input to Power-On Reset (POR) circuit.

1.2V

VCCAUX

Auxiliary supply voltage. Supplies Digital Clock Managers (DCMs), differential drivers, dedicated configuration pins, JTAG interface. Input to Power-On Reset (POR) circuit.

2.5V

VCCO_0

Supplies the output buffers in I/O Bank 0, the bank along the top edge of the FPGA.

Selectable, 3.3V, 2.5V, 1.8, 1.5V, or 1.2V

VCCO_1

Supplies the output buffers in I/O Bank 1, the bank along the right edge of the FPGA. In Byte-Wide Peripheral Interface (BPI) Parallel Flash Mode, connects to the same voltage as the Flash PROM.

Selectable, 3.3V, 2.5V, 1.8, 1.5V, or 1.2V

VCCO_2

Supplies the output buffers in I/O Bank 2, the bank along the bottom edge of the FPGA. Connects to the same voltage as the FPGA configuration source. Input to Power-On Reset (POR) circuit.

Selectable, 3.3V, 2.5V, 1.8, 1.5V, or 1.2V

VCCO_3

Supplies the output buffers in I/O Bank 3, the bank along the left edge of the FPGA.

Selectable, 3.3V, 2.5V, 1.8, 1.5V, or 1.2V

In a 3.3V-only application, all four VCCO supplies connect to 3.3V. However, Spartan-3E FPGAs provide the ability to bridge between different I/O voltages and standards by applying different voltages to the VCCO inputs of different banks. Refer to I/O Banking Rules for which I/O standards can be intermixed within a single I/O bank. Each I/O bank also has an separate, optional input voltage reference supply, called VREF. If the I/O bank includes an I/O standard that requires a voltage reference such as HSTL or SSTL, then all VREF pins within the I/O bank must be connected to the same voltage.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 110

Spartan-3E FPGA Family: Functional Description

Voltage Regulators

do not require Power-On Surge (POS) current to successfully configure.

Various power supply manufacturers offer complete power solutions for Xilinx FPGAs including some with integrated three-rail regulators specifically designed for Spartan-3 and Spartan-3E FPGAs. The Xilinx Power Corner website provides links to vendor solution guides and Xilinx power estimation and analysis tools.

Power Distribution System (PDS) Design and Decoupling/Bypass Capacitors Good power distribution system (PDS) design is important for all FPGA designs, but especially so for high performance applications, greater than 100 MHz. Proper design results in better overall performance, lower clock and DCM jitter, and a generally more robust system. Before designing the printed circuit board (PCB) for the FPGA design, please review XAPP623: Power Distribution System (PDS) Design: Using Bypass/Decoupling Capacitors.

Surplus ICCINT if VCCINT Applied before VCCAUX If the VCCINT supply is applied before the VCCAUX supply, the FPGA might draw a surplus ICCINT current in addition to the ICCINT quiescent current levels specified in Table 79, page 119. The momentary additional ICCINT surplus current might be a few hundred milliamperes under nominal conditions, significantly less than the instantaneous current consumed by the bypass capacitors at power-on. However, the surplus current immediately disappears when the VCCAUX supply is applied, and, in response, the FPGA’s ICCINT quiescent current demand drops to the levels specified in Table 79. The FPGA does not use or require the surplus current to successfully power-on and configure. If applying VCCINT before VCCAUX, ensure that the regulator does not have a foldback feature that could inadvertently shut down in the presence of the surplus current.

Configuration Data Retention, Brown-Out

Power-On Behavior For additional power-on behavior information, including I/O behavior before and during configuration, refer to the “Sequence of Events” chapter in UG332. Spartan-3E FPGAs have a built-in Power-On Reset (POR) circuit that monitors the three power rails required to successfully configure the FPGA. At power-up, the POR circuit holds the FPGA in a reset state until the VCCINT, VCCAUX, and VCCO Bank 2 supplies reach their respective input threshold levels (see Table 74 in Module 3). After all three supplies reach their respective thresholds, the POR reset is released and the FPGA begins its configuration process.

Supply Sequencing Because the three FPGA supply inputs must be valid to release the POR reset and can be supplied in any order, there are no FPGA-specific voltage sequencing requirements. Applying the FPGA’s VCCAUX supply before the VCCINT supply uses the least ICCINT current. Although the FPGA has no specific voltage sequence requirements, be sure to consider any potential sequencing requirement of the configuration device attached to the FPGA, such as an SPI serial Flash PROM, a parallel NOR Flash PROM, or a microcontroller. For example, Flash PROMs have a minimum time requirement before the PROM can be selected and this must be considered if the 3.3V supply is the last in the sequence. See Power-On Precautions if 3.3V Supply is Last in Sequence for more details.

The FPGA’s configuration data is stored in robust CMOS configuration latches. The data in these latches is retained even when the voltages drop to the minimum levels necessary to preserve RAM contents, as specified in Table 76. If, after configuration, the VCCAUX or VCCINT supply drops below its data retention voltage, the current device configuration must be cleared using one of the following methods: •

Force the VCCAUX or VCCINT supply voltage below the minimum Power On Reset (POR) voltage threshold (Table 74).



Assert PROG_B Low.

The POR circuit does not monitor the VCCO_2 supply after configuration. Consequently, dropping the VCCO_2 voltage does not reset the device by triggering a Power-On Reset (POR) event.

No Internal Charge Pumps or Free-Running Oscillators Some system applications are sensitive to sources of analog noise. Spartan-3E FPGA circuitry is fully static and does not employ internal charge pumps. The CCLK configuration clock is active during the FPGA configuration process. After configuration completes, the CCLK oscillator is automatically disabled unless the Bitstream Generator (BitGen) option Persist=Yes.

When all three supplies are valid, the minimum current required to power-on the FPGA equals the worst-case quiescent current, specified in Table 79. Spartan-3E FPGAs

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 111

Spartan-3E FPGA Family: Functional Description

Production Stepping The Spartan-3E FPGA family uses production stepping to indicate improved capabilities or enhanced features.

Designs operating on the Stepping 0 devices perform similarly on a Stepping 1 device.

Stepping 1 is, by definition, a functional superset of Stepping 0. Furthermore, configuration bitstreams generated for Stepping 0 are compatible with Stepping 1.

Differences Between Steppings Table 71 summarizes the feature and performance differences between Stepping 0 devices and Stepping 1 devices.

Table 71: Differences between Spartan-3E Production Stepping Levels Production status

Stepping 0

Stepping 1

Production from 2005 to 2007

Production starting March 2006

-4C only

-4C, -4I, -5C

Speed grade and operating conditions JTAG ID code

Different revision fields. See Table 67.

DCM DLL maximum input frequency

90 MHz (200 MHz for XC3S1200E)

240 MHz (-4 speed grade) 275 MHz (-5 speed grade)

DCM DFS output frequency range(s)

Split ranges at 5 – 90 MHz and 220 – 307 MHz (single range 5 – 307 MHz for XC3S1200E)

Continuous range: 5 – 311 MHz (-4) 5 – 333 MHz (-5)

No, single FPGA only

Yes

Supports multi-FPGA daisy-chain configurations from SPI Flash JTAG configuration supported when FPGA in BPI mode with a valid image in the attached parallel NOR Flash PROM JTAG EXTEST, INTEST, SAMPLE support Power sequencing when using HSWAP Pull-Up

No(1)

Yes

Yes: XC3S100E, XC3S250E, XC3S500E No(2) : XC3S1200E, XC3S1600E

Yes All Devices

Requires VCCINT before VCCAUX

Any sequence

No

Yes

PCI compliance Notes: 1. 2.

Workarounds exist. See Stepping 0 Limitations when Reprogramming via JTAG if FPGA Set for BPI Configuration. JTAG BYPASS and JTAG configuration are supported

Ordering a Later Stepping

Software Version Requirements

-5C and -4I devices, and -4C devices (with date codes 0901 (2009) and later) always support the Stepping 1 feature set independent of the stepping code. Optionally, to order only Stepping 1 for the -4C devices, append an “S1” suffix to the standard ordering code, where ‘1’ is the stepping number, as indicated in Table 72.

Production Spartan-3E applications must be processed using the Xilinx ISE 8.1i, Service Pack 3 or later development software, using the v1.21 or later speed files. The ISE 8.1i software implements critical bitstream generator updates.

Table 72: Spartan-3E Optional Stepping Ordering Stepping Number

Suffix Code

Status

0

None

Production

1

S1

Production

DS312 (v4.1) July 19, 2013 Product Specification

For additional information on Spartan-3E development software and known issues, see the following Answer Record: •

Xilinx Answer #22253 http://www.xilinx.com/support/answers/22253.htm

www.xilinx.com 112

Spartan-3E FPGA Family: Functional Description

Revision History The following table shows the revision history for this document. Date

Version

03/01/2005

1.0

Initial Xilinx release.

03/21/2005

1.1

Updated Figure 45. Modified title on Table 39 and Table 45.

11/23/2005

2.0

Updated values of On-Chip Differential Termination resistors. Updated Table 7. Updated configuration bitstream sizes for XC3S250E through XC3S1600E in Table 45, Table 51, Table 57, and Table 60. Added DLL Performance Differences Between Steppings. Added Stepping 0 Limitations when Reprogramming via JTAG if FPGA Set for BPI Configuration. Added Stepping 0 limitations when Daisy-Chaining in SPI configuration mode. Added Multiplier/Block RAM Interaction section. Updated Digital Clock Managers (DCMs) section, especially Phase Shifter (PS) portion. Corrected and enhanced the clock infrastructure diagram in Figure 45 and Table 41. Added CCLK Design Considerations section. Added Design Considerations for the HSWAP, M[2:0], and VS[2:0] Pins section. Added Spansion, Winbond, and Macronix to list of SPI Flash vendors in Table 53 and Table 56. Clarified that SPI mode configuration supports Atmel ‘C’- and ‘D’-series DataFlash. Updated the Programming Support section for SPI Flash PROMs. Added Power-On Precautions if PROM Supply is Last in Sequence, Compatible Flash Families, and BPI Mode Interaction with Right and Bottom Edge Global Clock Inputs sections to BPI configuration mode topic. Updated and amplified Powering Spartan-3E FPGAs section. Added Production Stepping section.

03/22/2006

3.0

Upgraded data sheet status to Preliminary. Updated Input Delay Functions and Figure 6. Added clarification that Input-only pins also have Pull-Up and Pull-Down Resistors. Added design note about address setup and hold requirements to Block RAM. Added warning message about software differences between ISE 8.1i, Service Pack 3 and earlier software to FIXED Phase Shift Mode and VARIABLE Phase Shift Mode. Added message about using GCLK1 in DLL Clock Input Connections and Clock Inputs. Updated Figure 45. Added additional information on HSWAP behavior to Pin Behavior During Configuration. Highlighted which pins have configuration pull-up resistors unaffected by HSWAP in Table 46. Updated bitstream image sizes for the XC3S1200E and XC3S1600E in Table 45, Table 51, Table 57, and Table 60. Clarified that ‘B’-series Atmel DataFlash SPI PROMs can be used in Commercial temperature range applications in Table 53 and Figure 54. Updated Figure 56. Updated Dynamically Loading Multiple Configuration Images Using MultiBoot Option section. Added design note about BPI daisy-chaining software support to BPI Daisy-Chaining section. Updated JTAG revision codes in Table 67. Added No Internal Charge Pumps or Free-Running Oscillators. Updated information on production stepping differences in Table 71. Updated Software Version Requirements.

04/10/2006

3.1

Updated JTAG User ID information. Clarified Note 1, Figure 5. Clarified that Figure 45 shows electrical connectivity and corrected left- and right-edge DCM coordinates. Updated Table 30, Table 31, and Table 32 to show the specific clock line driven by the associated BUFGMUX primitive. Corrected the coordinate locations for the associated BUFGMUX primitives in Table 31 and Table 32. Updated Table 41 to show that the I0-input is the preferred connection to a BUFGMUX.

05/19/2006

3.2

Made further clarifying changes to Figure 46, showing both direct inputs to BUFGMUX primitives and to DCMs. Added Atmel AT45DBxxxD-series DataFlash serial PROMs to Table 53. Added details that intermediate FPGAs in a BPI-mode, multi-FPGA configuration daisy-chain must be from either the Spartan-3E or the Virtex-5 FPGA families (see BPI Daisy-Chaining). Added Using JTAG Interface to Communicate to a Configured FPGA Design. Minor updates to Figure 66 and Figure 67. Clarified which Spartan-3E FPGA product options support the Readback feature, shown in Table 68.

05/30/2006

3.2.1

10/02/2006

3.3

Clarified that the block RAM Readback feature is available either on the -5 speed grade or the Industrial temperature range.

11/09/2006

3.4

Updated the description of the Input Delay Functions. The ODDR2 flip-flop with C0 or C1 Alignment is no longer supported. Updated Figure 5. Updated Table 6 for improved PCI input voltage tolerance. Replaced missing text in Clock Buffers/Multiplexers. Updated SPI Flash devices in Table 53. Updated parallel NOR Flash devices in Table 61. Direct, SPI Flash in-system Programming Support was added beginning with ISE 8.1i iMPACT software for STMicro and Atmel SPI PROMs. Updated Table 71 and Table 72 as Stepping 1 is in full production. Freshened various hyper links. Promoted Module 2 to Production status.

DS312 (v4.1) July 19, 2013 Product Specification

Revision

Corrected various typos and incorrect links.

www.xilinx.com 113

Spartan-3E FPGA Family: Functional Description

Date

Version

Revision

03/16/2007

3.5

Added information about new Spartan-3 Generation user guides (Design Documentation Available). Added cross-references to UG331: Spartan-3 Generation FPGA User Guide and to UG332: Spartan-3 Generation Configuration User Guide. Added note about possible JTAG configuration issues when the FPGA mode pins are set for Master mode and using software prior to ISE 9.1.01i (JTAG Mode). Removed a few lingering references to “weak” pull-up resistors, including in Figure 12. Removed vestigial references regarding the LDC[2:0] and HDC pins during Slave Parallel Mode configuration. These pins are not used in this configuration mode.

05/29/2007

3.6

Added information about HSWAP and PCI differences between steppings to Table 71. Removed “Performance Differences between Global Buffers” to match improved specs in Module 3. Updated PROG_B pulse width descriptions to match specification in Module 3.

04/18/2008

3.7

Corrected Figure 6 to show six taps and updated associated text. Added note for recommended pull-up on DONE in Table 55 and elsewhere. Added a caution regarding Persist of pins A20-A23. Updated Stepping description in Table 71 to note that only Stepping 1 is in production today. Updated links.

08/26/2009

3.8

Added a frequency limitation to Equation 6. Added a new Equation 7 with a frequency limitation. Added a Spread Spectrum, page 57 paragraph. Added Table 42, page 61. Updated a Flash vendor name in Table 61, page 89. Removed the < symbol from the flash read access times in Table 62, page 89. Revised the first paragraph in Configuration Sequence, page 102. Revised the first paragraph in Power-On Behavior, page 111. Revised the second paragraph in Production Stepping, page 112. Revised the first paragraph in Ordering a Later Stepping, page 112.

10/29/2012

4.0

Added Notice of Disclaimer. This product is not recommended for new designs. Updated the design note section in VARIABLE Phase Shift Mode. Added the VQ100 to the Quadrant Clock Routing section.

07/19/2013

4.1

Removed banner. This product IS recommended for new designs.

Notice of Disclaimer THE XILINX HARDWARE FPGA AND CPLD DEVICES REFERRED TO HEREIN (“PRODUCTS”) ARE SUBJECT TO THE TERMS AND CONDITIONS OF THE XILINX LIMITED WARRANTY WHICH CAN BE VIEWED AT http://www.xilinx.com/warranty.htm. THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY USE OF PRODUCTS IN AN APPLICATION OR ENVIRONMENT THAT IS NOT WITHIN THE SPECIFICATIONS STATED IN THE XILINX DATA SHEET. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, OR ANY OTHER APPLICATION THAT INVOKES THE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). USE OF PRODUCTS IN CRITICAL APPLICATIONS IS AT THE SOLE RISK OF CUSTOMER, SUBJECT TO APPLICABLE LAWS AND REGULATIONS. CRITICAL APPLICATIONS DISCLAIMER XILINX PRODUCTS (INCLUDING HARDWARE, SOFTWARE AND/OR IP CORES) ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS IN LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, CLASS III MEDICAL DEVICES, NUCLEAR FACILITIES, APPLICATIONS RELATED TO THE DEPLOYMENT OF AIRBAGS, OR ANY OTHER APPLICATIONS THAT COULD LEAD TO DEATH, PERSONAL INJURY OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (INDIVIDUALLY AND COLLECTIVELY, “CRITICAL APPLICATIONS”). FURTHERMORE, XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN ANY APPLICATIONS THAT AFFECT CONTROL OF A VEHICLE OR AIRCRAFT, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE OPERATOR. CUSTOMER AGREES, PRIOR TO USING OR DISTRIBUTING ANY SYSTEMS THAT INCORPORATE XILINX PRODUCTS, TO THOROUGHLY TEST THE SAME FOR SAFETY PURPOSES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN CRITICAL APPLICATIONS. AUTOMOTIVE APPLICATIONS DISCLAIMER XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS APPLICATIONS RELATED TO: (I) THE DEPLOYMENT OF AIRBAGS, (II) CONTROL OF A VEHICLE, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE OPERATOR, OR (III) USES THAT COULD LEAD TO DEATH OR PERSONAL INJURY. CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN SUCH APPLICATIONS.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 114

156

Spartan-3E FPGA Family: DC and Switching Characteristics

DS312 (v4.1) July 19, 2013

Product Specification

DC Electrical Characteristics In this section, specifications may be designated as Advance, Preliminary, or Production. These terms are defined as follows: Advance: Initial estimates are based on simulation, early characterization, and/or extrapolation from the characteristics of other families. Values are subject to change. Use as estimates, not for production. Preliminary: Based on characterization. Further changes are not expected. Production: These specifications are approved once the silicon has been characterized over numerous production lots. Parameter values are considered stable with no future changes expected.

All parameter limits are representative of worst-case supply voltage and junction temperature conditions. Unless otherwise noted, the published parameter values apply to all Spartan®-3E devices. AC and DC characteristics are specified using the same numbers for both commercial and industrial grades.

Absolute Maximum Ratings Stresses beyond those listed under Table 73, Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only; functional operation of the device at these or any other conditions beyond those listed under the Recommended Operating Conditions is not implied. Exposure to absolute maximum conditions for extended periods of time adversely affects device reliability.

Table 73: Absolute Maximum Ratings Symbol

Description

VCCINT

Internal supply voltage

VCCAUX

Conditions

Min

Max

Units

–0.5

1.32

V

Auxiliary supply voltage

–0.5

3.00

V

VCCO

Output driver supply voltage

–0.5

3.75

V

VREF

Input reference voltage

–0.5

VCCO + 0.5(1)

V

Commercial

–0.95

4.4

V

Industrial

–0.85

4.3

V

All temp. ranges

–0.5

VCCAUX + 0.5(3)

V

±100 ±2000 ±500 ±200

mA

VIN(1,2,3,4)

Voltage applied to all User I/O pins and Dual-Purpose pins Voltage applied to all Dedicated pins

Driver in a high-impedance state

IIK

Input clamp current per I/O pin

–0.5 V < VIN < (VCCO + 0.5 V)



VESD

Electrostatic Discharge Voltage

Human body model



Charged device model



Machine model



V V V

TJ

Junction temperature



125

°C

TSTG

Storage temperature

–65

150

°C

Notes: 1.

2.

3.

4. 5.

Each of the User I/O and Dual-Purpose pins is associated with one of the four banks’ VCCO rails. Keeping VIN within 500 mV of the associated VCCO rails or ground rail ensures that the internal diode junctions do not turn on. Table 77 specifies the VCCO range used to evaluate the maximum VIN voltage. Input voltages outside the -0.5V to VCCO + 0.5V (or VCCAUX + 0.5V) voltage range are require the IIK input diode clamp diode rating is met and no more than 100 pins exceed the range simultaneously. Prolonged exposure to such current may compromise device reliability. A sustained current of 10 mA will not compromise device reliability. See XAPP459: Eliminating I/O Coupling Effects when Interfacing Large-Swing Single-Ended Signals to User I/O Pins on Spartan-3 Families for more details. All Dedicated pins (PROG_B, DONE, TCK, TDI, TDO, and TMS) draw power from the VCCAUX rail (2.5V). Meeting the VIN max limit ensures that the internal diode junctions that exist between each of these pins and the VCCAUX rail do not turn on. Table 77 specifies the VCCAUX range used to evaluate the maximum VIN voltage. As long as the VIN max specification is met, oxide stress is not possible. See XAPP459: Eliminating I/O Coupling Effects when Interfacing Large-Swing Single-Ended Signals to User I/O Pins on Spartan-3 Families. For soldering guidelines, see UG112: Device Packaging and Thermal Characteristics and XAPP427: Implementation and Solder Reflow Guidelines for Pb-Free Packages.

© Copyright 2005–2013 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Spartan, ISE, Artix, Kintex, Zynq, Vivado, and other designated brands included herein are trademarks of Xilinx in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 115

Spartan-3E FPGA Family: DC and Switching Characteristics

Power Supply Specifications Table 74: Supply Voltage Thresholds for Power-On Reset Symbol

Description

Min

Max

Units

VCCINTT

Threshold for the VCCINT supply

0.4

1.0

V

VCCAUXT

Threshold for the VCCAUX supply

0.8

2.0

V

VCCO2T

Threshold for the VCCO Bank 2 supply

0.4

1.0

V

Notes: 1.

2.

VCCINT, VCCAUX, and VCCO supplies to the FPGA can be applied in any order. However, the FPGA’s configuration source (Platform Flash, SPI Flash, parallel NOR Flash, microcontroller) might have specific requirements. Check the data sheet for the attached configuration source. In Step 0 devices using the HSWAP internal pull-up, VCCINT must be applied before VCCAUX. To ensure successful power-on, VCCINT, VCCO Bank 2, and VCCAUX supplies must rise through their respective threshold-voltage ranges with no dips at any point.

Table 75: Supply Voltage Ramp Rate Symbol

Description

Min

Max

Units

VCCINTR

Ramp rate from GND to valid VCCINT supply level

0.2

50

ms

VCCAUXR

Ramp rate from GND to valid VCCAUX supply level

0.2

50

ms

VCCO2R

Ramp rate from GND to valid VCCO Bank 2 supply level

0.2

50

ms

Notes: 1.

2.

VCCINT, VCCAUX, and VCCO supplies to the FPGA can be applied in any order. However, the FPGA’s configuration source (Platform Flash, SPI Flash, parallel NOR Flash, microcontroller) might have specific requirements. Check the data sheet for the attached configuration source. In Step 0 devices using the HSWAP internal pull-up, VCCINT must be applied before VCCAUX. To ensure successful power-on, VCCINT, VCCO Bank 2, and VCCAUX supplies must rise through their respective threshold-voltage ranges with no dips at any point.

Table 76: Supply Voltage Levels Necessary for Preserving RAM Contents Symbol

Description

Min

Units

VDRINT

VCCINT level required to retain RAM data

1.0

V

VDRAUX

VCCAUX level required to retain RAM data

2.0

V

Notes: 1.

RAM contents include configuration data.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 116

Spartan-3E FPGA Family: DC and Switching Characteristics

General Recommended Operating Conditions Table 77: General Recommended Operating Conditions Symbol TJ

Description Junction temperature

Commercial Industrial

Min

Nominal

Max

Units

0



85

°C

–40



100

°C

VCCINT

Internal supply voltage

1.140

1.200

1.260

V

VCCO (1)

Output driver supply voltage

1.100

-

3.465

V

VCCAUX VIN(2,3)

Auxiliary supply voltage Input voltage extremes to avoid turning on I/O protection diodes

I/O, Input-only, and Dual-Purpose pins (4) Dedicated

TIN

pins(6)

Input signal transition time(7)

2.375

2.500

2.625

V

IP or IO_#

–0.5



VCCO + 0.5

V

IO_Lxxy_#(5)

–0.5



VCCO + 0.5

V

–0.5



VCCAUX + 0.5

V





500

ns

Notes: 1. 2. 3. 4.

5. 6. 7.

This VCCO range spans the lowest and highest operating voltages for all supported I/O standards. Table 80 lists the recommended VCCO range specific to each of the single-ended I/O standards, and Table 82 lists that specific to the differential standards. Input voltages outside the recommended range require the IIK input clamp diode rating is met and no more than 100 pins exceed the range simultaneously. Refer to Table 73. See XAPP459: Eliminating I/O Coupling Effects when Interfacing Large-Swing Single-Ended Signals to User I/O Pins on Spartan-3 Families. Each of the User I/O and Dual-Purpose pins is associated with one of the four banks’ VCCO rails. Meeting the VIN limit ensures that the internal diode junctions that exist between these pins and their associated VCCO and GND rails do not turn on. The absolute maximum rating is provided in Table 73. For single-ended signals that are placed on a differential-capable I/O, VIN of –0.2V to –0.5V is supported but can cause increased leakage between the two pins. See Parasitic Leakage in UG331, Spartan-3 Generation FPGA User Guide. All Dedicated pins (PROG_B, DONE, TCK, TDI, TDO, and TMS) draw power from the VCCAUX rail (2.5V). Meeting the VIN max limit ensures that the internal diode junctions that exist between each of these pins and the VCCAUX and GND rails do not turn on. Measured between 10% and 90% VCCO. Follow Signal Integrity recommendations.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 117

Spartan-3E FPGA Family: DC and Switching Characteristics

General DC Characteristics for I/O Pins Table 78: General DC Characteristics of User I/O, Dual-Purpose, and Dedicated Pins Symbol IL

(3)

IRPU(2)

RPU(2)

Description Leakage current at User I/O, Input-only, Dual-Purpose, and Dedicated pins Current through pull-up resistor at User I/O, Dual-Purpose, Input-only, and Dedicated pins

Equivalent pull-up resistor value at User I/O, Dual-Purpose, Input-only, and Dedicated pins (based on IRPU per Note 2)

Test Conditions

Min

Typ

Max

Units

Driver is in a high-impedance state, VIN = 0V or VCCO max, sample-tested

–10



+10

μA

VIN = 0V, VCCO = 3.3V

–0.36



–1.24

mA

VIN = 0V, VCCO = 2.5V

–0.22



–0.80

mA

VIN = 0V, VCCO = 1.8V

–0.10



–0.42

mA

VIN = 0V, VCCO = 1.5V

–0.06



–0.27

mA

VIN = 0V, VCCO = 1.2V

–0.04



–0.22

mA

VIN = 0V, VCCO = 3.0V to 3.465V

2.4



10.8



VIN = 0V, VCCO = 2.3V to 2.7V

2.7



11.8



VIN = 0V, VCCO = 1.7V to 1.9V

4.3



20.2



VIN = 0V, VCCO =1.4V to 1.6V

5.0



25.9



VIN = 0V, VCCO = 1.14V to 1.26V

5.5



32.0



IRPD(2)

Current through pull-down resistor at User I/O, Dual-Purpose, Input-only, and Dedicated pins

VIN = VCCO

0.10



0.75

mA

RPD(2)

Equivalent pull-down resistor value at User I/O, Dual-Purpose, Input-only, and Dedicated pins (based on IRPD per Note 2)

VIN = VCCO = 3.0V to 3.465V

4.0



34.5



VIN = VCCO = 2.3V to 2.7V

3.0



27.0



VIN = VCCO = 1.7V to 1.9V

2.3



19.0



VIN = VCCO = 1.4V to 1.6V

1.8



16.0



VIN = VCCO = 1.14V to 1.26V

1.5



12.6



All VCCO levels

–10



+10

μA







10

pF

VOCM Min ≤ VICM ≤ VOCM Max VOD Min ≤ VID ≤ VOD Max VCCO = 2.5V



120



Ω

IREF

VREF current per pin

CIN

Input capacitance

RDT

Resistance of optional differential termination circuit within a differential I/O pair. Not available on Input-only pairs.

Notes: 1. 2. 3.

The numbers in this table are based on the conditions set forth in Table 77. This parameter is based on characterization. The pull-up resistance RPU = VCCO / IRPU. The pull-down resistance RPD = VIN / IRPD. For single-ended signals that are placed on a differential-capable I/O, VIN of –0.2V to –0.5V is supported but can cause increased leakage between the two pins. See Parasitic Leakage in UG331, Spartan-3 Generation FPGA User Guide.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 118

Spartan-3E FPGA Family: DC and Switching Characteristics

Quiescent Current Requirements Table 79: Quiescent Supply Current Characteristics Symbol ICCINTQ

ICCOQ

ICCAUXQ

Description Quiescent VCCINT supply current

Quiescent VCCO supply current

Quiescent VCCAUX supply current

Industrial Maximum(1)

Typical

Commercial Maximum(1)

XC3S100E

8

27

36

mA

XC3S250E

15

78

104

mA

XC3S500E

25

106

145

mA

XC3S1200E

50

259

324

mA

XC3S1600E

65

366

457

mA

XC3S100E

0.8

1.0

1.5

mA

XC3S250E

0.8

1.0

1.5

mA

XC3S500E

0.8

1.0

1.5

mA

XC3S1200E

1.5

2.0

2.5

mA

XC3S1600E

1.5

2.0

2.5

mA

XC3S100E

8

12

13

mA

XC3S250E

12

22

26

mA

XC3S500E

18

31

34

mA

XC3S1200E

35

52

59

mA

XC3S1600E

45

76

86

mA

Device

Units

Notes: 1. 2. 3.

4.

The maximum numbers in this table indicate the minimum current each power rail requires in order for the FPGA to power-on successfully. The numbers in this table are based on the conditions set forth in Table 77. Quiescent supply current is measured with all I/O drivers in a high-impedance state and with all pull-up/pull-down resistors at the I/O pads disabled. Typical values are characterized using typical devices at room temperature (TJ of 25°C at VCCINT = 1.2 V, VCCO = 3.3V, and VCCAUX = 2.5V). The maximum limits are tested for each device at the respective maximum specified junction temperature and at maximum voltage limits with VCCINT = 1.26V, VCCO = 3.465V, and VCCAUX = 2.625V. The FPGA is programmed with a “blank” configuration data file (i.e., a design with no functional elements instantiated). For conditions other than those described above, (e.g., a design including functional elements), measured quiescent current levels may be different than the values in the table. For more accurate estimates for a specific design, use the Xilinx® XPower tools. There are two recommended ways to estimate the total power consumption (quiescent plus dynamic) for a specific design: a) The Spartan-3E XPower Estimator provides quick, approximate, typical estimates, and does not require a netlist of the design. b) XPower Analyzer uses a netlist as input to provide maximum estimates as well as more accurate typical estimates.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 119

Spartan-3E FPGA Family: DC and Switching Characteristics

Single-Ended I/O Standards Table 80: Recommended Operating Conditions for User I/Os Using Single-Ended Standards IOSTANDARD Attribute

VCCO for Drivers(2) Min (V)

Nom (V)

Max (V)

LVTTL

3.0

3.3

LVCMOS33(4)

3.0

LVCMOS25(4,5)

VREF Min (V)

Nom (V)

VIL Max (V)

VIH(3)

Max (V)

Min (V)

3.465

0.8

2.0

3.3

3.465

0.8

2.0

2.3

2.5

2.7

0.7

1.7

LVCMOS18

1.65

1.8

1.95

0.4

0.8

LVCMOS15

1.4

1.5

1.6

0.4

0.8

LVCMOS12

1.1

1.2

1.3

0.4

0.7

PCI33_3(6)

3.0

3.3

3.465

0.3 • VCCO

0.5 • VCCO

PCI66_3(6)

3.0

3.3

3.465

0.3 • VCCO

0.5 • VCCO

HSTL_I_18

1.7

1.8

1.9

0.8

0.9

1.1

VREF - 0.1

VREF + 0.1

HSTL_III_18

1.7

1.8

1.9

-

1.1

-

VREF - 0.1

VREF + 0.1

SSTL18_I

1.7

1.8

1.9

0.833

0.900

0.969

VREF - 0.125

VREF + 0.125

SSTL2_I

2.3

2.5

2.7

1.15

1.25

1.35

VREF - 0.125

VREF + 0.125

VREF is not used for these I/O standards

Notes: 1.

2. 3. 4. 5.

6.

Descriptions of the symbols used in this table are as follows: VCCO – the supply voltage for output drivers VREF – the reference voltage for setting the input switching threshold VIL – the input voltage that indicates a Low logic level VIH – the input voltage that indicates a High logic level The VCCO rails supply only output drivers, not input circuits. For device operation, the maximum signal voltage (VIH max) may be as high as VIN max. See Table 73. There is approximately 100 mV of hysteresis on inputs using LVCMOS33 and LVCMOS25 I/O standards. All Dedicated pins (PROG_B, DONE, TCK, TDI, TDO, and TMS) use the LVCMOS25 standard and draw power from the VCCAUX rail (2.5V). The Dual-Purpose configuration pins use the LVCMOS standard before the User mode. When using these pins as part of a standard 2.5V configuration interface, apply 2.5V to the VCCO lines of Banks 0, 1, and 2 at power-on as well as throughout configuration. For information on PCI IP solutions, see www.xilinx.com/pci. The PCIX IOSTANDARD is available and has equivalent characteristics but no PCI-X IP is supported.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 120

Spartan-3E FPGA Family: DC and Switching Characteristics Table 81: DC Characteristics of User I/Os Using Single-Ended Standards (Cont’d)

Table 81: DC Characteristics of User I/Os Using Single-Ended Standards Test Conditions

IOSTANDARD Attribute LVTTL(3)

IOH IOL (mA) (mA)

Logic Level Characteristics VOL Max (V)

VOH Min (V)

0.4

2.4

IOSTANDARD Attribute SSTL2_I

2

2

–2

4

4

–4

Notes:

6

6

–6

1.

8

8

–8

2.

12

12

–12

16

16

–16

2

2

–2

4

4

–4

6

6

–6

8

8

–8

12

12

–12

16

16

–16

2

2

–2

4

4

–4

6

6

–6

8

8

–8

12

12

–12

2

2

–2

4

4

–4

6

6

–6

8

8

–8

2

2

–2

4

4

–4

6

6

–6

2

2

PCI33_3(4)

LVCMOS33(3)

0.4

VCCO – 0.4 3. 4.

LVCMOS25(3)

0.4

VCCO – 0.4

0.4

VCCO – 0.4

0.4

VCCO – 0.4

–2

0.4

VCCO – 0.4

1.5

–0.5

10% VCCO

90% VCCO

PCI66_3(4)

1.5

–0.5

10% VCCO

90% VCCO

HSTL_I_18

8

–8

0.4

VCCO – 0.4

HSTL_III_18

24

–8

0.4

VCCO – 0.4

SSTL18_I

6.7

–6.7

VTT – 0.475

VTT + 0.475

LVCMOS18(3)

LVCMOS15(3)

LVCMOS12(3)

DS312 (v4.1) July 19, 2013 Product Specification

Test Conditions IOH IOL (mA) (mA) 8.1

–8.1

Logic Level Characteristics VOL Max (V)

VOH Min (V)

VTT – 0.61

VTT + 0.61

The numbers in this table are based on the conditions set forth in Table 77 and Table 80. Descriptions of the symbols used in this table are as follows: IOL – the output current condition under which VOL is tested IOH – the output current condition under which VOH is tested VOL – the output voltage that indicates a Low logic level VOH – the output voltage that indicates a High logic level VCCO – the supply voltage for output drivers VTT – the voltage applied to a resistor termination For the LVCMOS and LVTTL standards: the same VOL and VOH limits apply for both the Fast and Slow slew attributes. Tested according to the relevant PCI specifications. For information on PCI IP solutions, see www.xilinx.com/pci. The PCIX IOSTANDARD is available and has equivalent characteristics but no PCI-X IP is supported.

www.xilinx.com 121

Spartan-3E FPGA Family: DC and Switching Characteristics

Differential I/O Standards X-Ref Target - Figure 69

VINP Internal Logic

VINN

VINN

VID

50%

VINP

Differential I/O Pair Pins

P N

VICM

GND level VICM = Input common mode voltage =

VINP + VINN 2

VID = Differential input voltage = VINP - VINN DS099-3_01_012304

Figure 69: Differential Input Voltages Table 82: Recommended Operating Conditions for User I/Os Using Differential Signal Standards IOSTANDARD Attribute

VCCO for Drivers(1)

VID

Min (V)

Nom (V)

Max (V)

Min (mV)

LVDS_25

2.375

2.50

2.625

100

350

BLVDS_25

2.375

2.50

2.625

100

MINI_LVDS_25

2.375

2.50

2.625

LVPECL_25(2) RSDS_25

Inputs Only

VICM

Nom (mV) Max (mV)

Min (V)

Nom (V)

Max (V)

600

0.30

1.25

2.20

350

600

0.30

1.25

2.20

200

-

600

0.30

-

2.2

100

800

1000

0.5

1.2

2.0

2.375

2.50

2.625

100

200

-

0.3

1.20

1.4

DIFF_HSTL_I_18

1.7

1.8

1.9

100

-

-

0.8

-

1.1

DIFF_HSTL_III_18

1.7

1.8

1.9

100

-

-

0.8

-

1.1

DIFF_SSTL18_I

1.7

1.8

1.9

100

-

-

0.7

-

1.1

DIFF_SSTL2_I

2.3

2.5

2.7

100

-

-

1.0

-

1.5

Notes: 1. 2.

The VCCO rails supply only differential output drivers, not input circuits. VREF inputs are not used for any of the differential I/O standards.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 122

Spartan-3E FPGA Family: DC and Switching Characteristics

X-Ref Target - Figure 70

VOUTP Internal Logic

Differential I/O Pair Pins

P N

VOUTN

VOH

VOUTN

VOD

50%

VOUTP

VOL

VOCM GND level

VOCM = Output common mode voltage =

VOUTP + VOUTN

2 VOD = Output differential voltage = VOUTP - VOUTN VOH = Output voltage indicating a High logic level VOL = Output voltage indicating a Low logic level

DS312-3_03_021505

Figure 70: Differential Output Voltages Table 83: DC Characteristics of User I/Os Using Differential Signal Standards IOSTANDARD Attribute

ΔVOD

VOD

ΔVOCM

VOCM

Min (mV)

Typ (mV)

Max (mV)

Min (mV)

Max (mV)

Min (V)

LVDS_25

250

350

450





BLVDS_25

250

350

450





MINI_LVDS_25

300



600



RSDS_25

VOH

VOL

Typ (V)

Max (V)

Min (mV)

Max (mV)

Min (V)

Max (V)

1.125



1.375











1.20











50

1.0



1.4



50





100



400





1.1



1.4









DIFF_HSTL_I_18





















VCCO – 0.4

0.4

DIFF_HSTL_III_18





















VCCO – 0.4

0.4

DIFF_SSTL18_I





















VTT + 0.475 VTT – 0.475

DIFF_SSTL2_I





















VTT + 0.61

VTT – 0.61

Notes: 1. 2. 3.

The numbers in this table are based on the conditions set forth in Table 77 and Table 82. Output voltage measurements for all differential standards are made with a termination resistor (RT) of 100Ω across the N and P pins of the differential signal pair. The exception is for BLVDS, shown in Figure 71. At any given time, no more than two of the following differential output standards may be assigned to an I/O bank: LVDS_25, RSDS_25, MINI_LVDS_25

X-Ref Target - Figure 71

1/4th of Bourns Part Number CAT16-LV4F12

VCCO = 2.5V

VCCO = 2.5V

Z0 = 50Ω

165Ω

FPGA Out

1/4th of Bourns Part Number CAT16-PT4F4

140Ω

Z0 = 50Ω

100Ω

FPGA In

165Ω ds312-3_07_041108

Figure 71: External Termination Resistors for BLVDS Transmitter and BLVDS Receiver

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 123

Spartan-3E FPGA Family: DC and Switching Characteristics

Switching Characteristics All Spartan-3E FPGAs ship in two speed grades: -4 and the higher performance -5. Switching characteristics in this document may be designated as Advance, Preliminary, or Production, as shown in Table 84. Each category is defined as follows: Advance: These specifications are based on simulations only and are typically available soon after establishing FPGA specifications. Although speed grades with this designation are considered relatively stable and conservative, some under-reporting might still occur. Preliminary: These specifications are based on complete early silicon characterization. Devices and speed grades with this designation are intended to give a better indication of the expected performance of production silicon. The probability of under-reporting preliminary delays is greatly reduced compared to Advance data. Production: These specifications are approved once enough production silicon of a particular device family member has been characterized to provide full correlation between speed files and devices over numerous production lots. There is no under-reporting of delays, and customers receive formal notification of any subsequent changes. Typically, the slowest speed grades transition to Production before faster speed grades.

Software Version Requirements Production-quality systems must use FPGA designs compiled using a speed file designated as PRODUCTION status. FPGAs designs using a less mature speed file designation should only be used during system prototyping or pre-production qualification. FPGA designs with speed files designated as Advance or Preliminary should not be used in a production-quality system. Whenever a speed file designation changes, as a device matures toward Production status, rerun the latest Xilinx ISE software on the FPGA design to ensure that the FPGA design incorporates the latest timing information and software updates.

Timing parameters and their representative values are selected for inclusion below either because they are important as general design requirements or they indicate fundamental device performance characteristics. The Spartan-3E speed files (v1.27), part of the Xilinx Development Software, are the original source for many but not all of the values. The speed grade designations for these files are shown in Table 84. For more complete, more precise, and worst-case data, use the values reported by the Xilinx static timing analyzer (TRACE in the Xilinx development software) and back-annotated to the simulation netlist. Table 84: Spartan-3E v1.27 Speed Grade Designations Device

Advance

Preliminary

Production

XC3S100E

-MIN, -4, -5

XC3S250E

-MIN, -4, -5

XC3S500E

-MIN, -4, -5

XC3S1200E

-MIN, -4, -5

XC3S1600E

-MIN, -4, -5

Table 85 provides the history of the Spartan-3E speed files since all devices reached Production status. Table 85: Spartan-3E Speed File Version History Version

ISE Release

1.27

9.2.03i

Added XA Automotive.

1.26

8.2.02i

Added -0/-MIN speed grade, which includes minimum values.

1.25

8.2.01i

Added XA Automotive devices to speed file. Improved model for left and right DCMs.

1.23

8.2i

Updated input setup/hold values based on default IFD_DELAY_VALUE settings.

1.21

8.1.03i

Description

All Spartan-3E FPGAs and all speed grades elevated to Production status.

All parameter limits are representative of worst-case supply voltage and junction temperature conditions. Unless otherwise noted, the published parameter values apply to all Spartan-3E devices. AC and DC characteristics are specified using the same numbers for both commercial and industrial grades. Create a Xilinx user account and sign up to receive automatic e-mail notification whenever this data sheet or the associated user guides are updated. Sign Up for Alerts on Xilinx.com http://secure.xilinx.com/webreg/register.do ?group=myprofile&languageID=1

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 124

Spartan-3E FPGA Family: DC and Switching Characteristics

I/O Timing Table 86: Pin-to-Pin Clock-to-Output Times for the IOB Output Path Speed Grade Symbol

Description

Conditions

Device

-5

-4

Units

Max(2)

Max(2)

XC3S100E

2.66

2.79

ns

XC3S250E

3.00

3.45

ns

XC3S500E

3.01

3.46

ns

XC3S1200E

3.01

3.46

ns

XC3S1600E

3.00

3.45

ns

XC3S100E

5.60

5.92

ns

XC3S250E

4.91

5.43

ns

XC3S500E

4.98

5.51

ns

XC3S1200E

5.36

5.94

ns

XC3S1600E

5.45

6.05

ns

Clock-to-Output Times TICKOFDCM

TICKOF

When reading from the Output Flip-Flop (OFF), the time from the active transition on the Global Clock pin to data appearing at the Output pin. The DCM is used.

When reading from OFF, the time from the active transition on the Global Clock pin to data appearing at the Output pin. The DCM is not used.

LVCMOS25(3), 12 mA output drive, Fast slew rate, with DCM(4)

LVCMOS25(3),

12 mA output drive, Fast slew rate, without DCM

Notes: 1. 2. 3.

4.

The numbers in this table are tested using the methodology presented in Table 95 and are based on the operating conditions set forth in Table 77 and Table 80. For minimums, use the values reported by the Xilinx timing analyzer. This clock-to-output time requires adjustment whenever a signal standard other than LVCMOS25 is assigned to the Global Clock Input or a standard other than LVCMOS25 with 12 mA drive and Fast slew rate is assigned to the data Output. If the former is true, add the appropriate Input adjustment from Table 91. If the latter is true, add the appropriate Output adjustment from Table 94. DCM output jitter is included in all measurements.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 125

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 87: Pin-to-Pin Setup and Hold Times for the IOB Input Path (System Synchronous) Symbol

Description

Conditions

IFD_ DELAY_ VALUE=

Speed Grade Device

-5

-4

Units

Min

Min

XC3S100E

2.65

2.98

ns

XC3S250E

2.25

2.59

ns

XC3S500E

2.25

2.59

ns

XC3S1200E

2.25

2.58

ns

XC3S1600E

2.25

2.59

ns

2

XC3S100E

3.16

3.58

ns

3

XC3S250E

3.44

3.91

ns

3

XC3S500E

4.00

4.73

ns

3

XC3S1200E

2.60

3.31

ns

3

XC3S1600E

3.33

3.77

ns

0

XC3S100E

–0.54

–0.52

ns

XC3S250E

0.06

0.14

ns

XC3S500E

0.07

0.14

ns

XC3S1200E

0.07

0.15

ns

XC3S1600E

0.06

0.14

ns

2

XC3S100E

–0.31

–0.24

ns

3

XC3S250E

–0.32

–0.32

ns

3

XC3S500E

–0.77

–0.77

ns

3

XC3S1200E

0.13

0.16

ns

3

XC3S1600E

–0.05

–0.03

ns

Setup Times TPSDCM

TPSFD

When writing to the Input Flip-Flop (IFF), the time from the setup of data at the Input pin to the active transition at a Global Clock pin. The DCM is used. No Input Delay is programmed.

LVCMOS25(2), IFD_DELAY_VALUE = 0, with DCM(3)

LVCMOS25(2),

When writing to IFF, the time from the setup of data at the IFD_DELAY_VALUE = Input pin to an active transition at default software setting the Global Clock pin. The DCM is not used. The Input Delay is programmed.

0

Hold Times TPHDCM

TPHFD

When writing to IFF, the time from the active transition at the Global Clock pin to the point when data must be held at the Input pin. The DCM is used. No Input Delay is programmed.

LVCMOS25(4), IFD_DELAY_VALUE = 0, with DCM(3)

LVCMOS25(4),

When writing to IFF, the time from the active transition at the IFD_DELAY_VALUE = Global Clock pin to the point default software setting when data must be held at the Input pin. The DCM is not used. The Input Delay is programmed.

Notes: 1. 2.

3. 4.

The numbers in this table are tested using the methodology presented in Table 95 and are based on the operating conditions set forth in Table 77 and Table 80. This setup time requires adjustment whenever a signal standard other than LVCMOS25 is assigned to the Global Clock Input or the data Input. If this is true of the Global Clock Input, subtract the appropriate adjustment from Table 91. If this is true of the data Input, add the appropriate Input adjustment from the same table. DCM output jitter is included in all measurements. This hold time requires adjustment whenever a signal standard other than LVCMOS25 is assigned to the Global Clock Input or the data Input. If this is true of the Global Clock Input, add the appropriate Input adjustment from Table 91. If this is true of the data Input, subtract the appropriate Input adjustment from the same table. When the hold time is negative, it is possible to change the data before the clock’s active edge.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 126

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 88: Setup and Hold Times for the IOB Input Path Symbol

Description

Conditions

Speed Grade

IFD_ DELAY_ VALUE=

Device

-5

-4

Units

Min

Min

1.84

2.12

ns

ns

Setup Times TIOPICK

Time from the setup of data at LVCMOS25(2), the Input pin to the active IFD_DELAY_VALUE = 0 transition at the ICLK input of the Input Flip-Flop (IFF). No Input Delay is programmed.

0

All

TIOPICKD

Time from the setup of data at LVCMOS25(2), the Input pin to the active IFD_DELAY_VALUE = transition at the IFF’s ICLK input. default software setting The Input Delay is programmed.

2

XC3S100E

6.12

7.01

3

All Others

6.76

7.72

0

All

–0.76

–0.76

ns

2

XC3S100E

–3.93

–3.93

ns

3

All Others

–3.50

–3.50

All

1.57

1.80

Hold Times LVCMOS25(3), IFD_DELAY_VALUE = 0

TIOICKP

Time from the active transition at the IFF’s ICLK input to the point where data must be held at the Input pin. No Input Delay is programmed.

TIOICKPD

Time from the active transition at LVCMOS25(3), the IFF’s ICLK input to the point IFD_DELAY_VALUE = where data must be held at the default software setting Input pin. The Input Delay is programmed.

Set/Reset Pulse Width TRPW_IOB

Minimum pulse width to SR control input on IOB

ns

Notes: 1. 2. 3.

The numbers in this table are tested using the methodology presented in Table 95 and are based on the operating conditions set forth in Table 77 and Table 80. This setup time requires adjustment whenever a signal standard other than LVCMOS25 is assigned to the data Input. If this is true, add the appropriate Input adjustment from Table 91. These hold times require adjustment whenever a signal standard other than LVCMOS25 is assigned to the data Input. If this is true, subtract the appropriate Input adjustment from Table 91. When the hold time is negative, it is possible to change the data before the clock’s active edge.

Table 89: Sample Window (Source Synchronous) Symbol TSAMP

Description

Max

Units

Setup and hold capture window of an IOB input flip-flop

The input capture sample window value is highly specific to a particular application, device, package, I/O standard, I/O placement, DCM usage, and clock buffer. Please consult the appropriate Xilinx application note for application-specific values. • XAPP485: 1:7 Deserialization in Spartan-3E FPGAs at Speeds Up to 666 Mbps

ps

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 127

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 90: Propagation Times for the IOB Input Path Symbol

Description

Conditions

Speed Grade

IFD_ DELAY_ VALUE=

Device

-5

-4

Min

Min

Units

Propagation Times TIOPLI

The time it takes for data to travel LVCMOS25(2), from the Input pin through the IFD_DELAY_VALUE = 0 IFF latch to the I output with no input delay programmed

0

All

1.96

2.25

ns

TIOPLID

The time it takes for data to travel LVCMOS25(2), from the Input pin through the IFD_DELAY_VALUE = IFF latch to the I output with the default software setting input delay programmed

2

XC3S100E

5.40

5.97

ns

3

All Others

6.30

7.20

Notes: 1. 2.

The numbers in this table are tested using the methodology presented in Table 95 and are based on the operating conditions set forth in Table 77 and Table 80. This propagation time requires adjustment whenever a signal standard other than LVCMOS25 is assigned to the data Input. When this is true, add the appropriate Input adjustment from Table 91.

Table 91: Input Timing Adjustments by IOSTANDARD (Cont’d)

Table 91: Input Timing Adjustments by IOSTANDARD

Convert Input Time from LVCMOS25 to the Following Signal Standard (IOSTANDARD)

Add the Adjustment Below Speed Grade -5

Units

-4

Convert Input Time from LVCMOS25 to the Following Signal Standard (IOSTANDARD)

Add the Adjustment Below Speed Grade -5

-4

Units

Differential Standards

Single-Ended Standards LVTTL

0.42

0.43

ns

LVDS_25

0.48

0.49

ns

LVCMOS33

0.42

0.43

ns

BLVDS_25

0.39

0.39

ns

LVCMOS25

0

0

ns

MINI_LVDS_25

0.48

0.49

ns

LVCMOS18

0.96

0.98

ns

LVPECL_25

0.27

0.27

ns

LVCMOS15

0.62

0.63

ns

RSDS_25

0.48

0.49

ns

LVCMOS12

0.26

0.27

ns

DIFF_HSTL_I_18

0.48

0.49

ns

PCI33_3

0.41

0.42

ns

DIFF_HSTL_III_18

0.48

0.49

ns

PCI66_3

0.41

0.42

ns

DIFF_SSTL18_I

0.30

0.30

ns

HSTL_I_18

0.12

0.12

ns

DIFF_SSTL2_I

0.32

0.32

ns

HSTL_III_18

0.17

0.17

ns

Notes:

SSTL18_I

0.30

0.30

ns

1.

SSTL2_I

0.15

0.15

ns 2.

DS312 (v4.1) July 19, 2013 Product Specification

The numbers in this table are tested using the methodology presented in Table 95 and are based on the operating conditions set forth in Table 77, Table 80, and Table 82. These adjustments are used to convert input path times originally specified for the LVCMOS25 standard to times that correspond to other signal standards.

www.xilinx.com 128

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 92: Timing for the IOB Output Path Speed Grade Symbol

Description

Conditions

Device

-5

-4

Min

Min

Units

Clock-to-Output Times TIOCKP

When reading from the Output Flip-Flop (OFF), the time from the active transition at the OCLK input to data appearing at the Output pin

LVCMOS25(2), 12 mA output drive, Fast slew rate

All

2.18

2.50

ns

LVCMOS25(2), 12 mA output drive, Fast slew rate

All

2.24

2.58

ns

2.32

2.67

ns

LVCMOS25(2), 12 mA output drive, Fast slew rate

All

3.27

3.76

ns

8.40

9.65

ns

Propagation Times TIOOP

The time it takes for data to travel from the IOB’s O input to the Output pin

TIOOLP

The time it takes for data to travel from the O input through the OFF latch to the Output pin

Set/Reset Times TIOSRP

Time from asserting the OFF’s SR input to setting/resetting data at the Output pin

TIOGSRQ

Time from asserting the Global Set Reset (GSR) input on the STARTUP_SPARTAN3E primitive to setting/resetting data at the Output pin

Notes: 1. 2. 3.

The numbers in this table are tested using the methodology presented in Table 95 and are based on the operating conditions set forth in Table 77 and Table 80. This time requires adjustment whenever a signal standard other than LVCMOS25 with 12 mA drive and Fast slew rate is assigned to the data Output. When this is true, add the appropriate Output adjustment from Table 94. For minimum delays use the values reported by the Timing Analyzer.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 129

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 93: Timing for the IOB Three-State Path Speed Grade Symbol

Description

Conditions

Device

-5

-4

Units

Max

Max

All

1.49

1.71

ns

All

2.70

3.10

ns

Synchronous Output Enable/Disable Times TIOCKHZ

Time from the active transition at the OTCLK input of the Three-state Flip-Flop (TFF) to when the Output pin enters the high-impedance state

TIOCKON(2)

Time from the active transition at TFF’s OTCLK input to when the Output pin drives valid data

LVCMOS25, 12 mA output drive, Fast slew rate

Asynchronous Output Enable/Disable Times TGTS

Time from asserting the Global Three State (GTS) input on the STARTUP_SPARTAN3E primitive to when the Output pin enters the high-impedance state

LVCMOS25, 12 mA output drive, Fast slew rate

All

8.52

9.79

ns

TIOSRHZ

Time from asserting TFF’s SR input to when the Output pin enters a high-impedance state

All

2.11

2.43

ns

TIOSRON(2)

Time from asserting TFF’s SR input at TFF to when the Output pin drives valid data

LVCMOS25, 12 mA output drive, Fast slew rate

All

3.32

3.82

ns

Set/Reset Times

Notes: 1. 2. 3.

The numbers in this table are tested using the methodology presented in Table 95 and are based on the operating conditions set forth in Table 77 and Table 80. This time requires adjustment whenever a signal standard other than LVCMOS25 with 12 mA drive and Fast slew rate is assigned to the data Output. When this is true, add the appropriate Output adjustment from Table 94. For minimum delays use the values reported by the Timing Analyzer.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 130

Spartan-3E FPGA Family: DC and Switching Characteristics Table 94: Output Timing Adjustments for IOB (Cont’d)

Table 94: Output Timing Adjustments for IOB Convert Output Time from LVCMOS25 with 12mA Drive and Fast Slew Rate to the Following Signal Standard (IOSTANDARD)

Add the Adjustment Below

Units

Speed Grade -5

LVCMOS18

Slow

Fast

LVCMOS33

Slow

Fast

LVCMOS25

Slow

Fast

Units

Speed Grade -4

2 mA

5.03

5.24

ns

2 mA

5.20

5.41

ns

4 mA

3.08

3.21

ns

4 mA

2.32

2.41

ns

6 mA

2.39

2.49

ns

6 mA

1.83

1.90

ns

8 mA

1.83

1.90

ns

8 mA

0.64

0.67

ns

2 mA

3.98

4.15

ns

12 mA

0.68

0.70

ns

4 mA

2.04

2.13

ns

1.09

1.14

ns

Fast

16 mA

0.41

0.43

ns

6 mA

2 mA

4.80

5.00

ns

8 mA

0.72

0.75

ns

4 mA

1.88

1.96

ns

2 mA

4.49

4.68

ns

6 mA

1.39

1.45

ns

4 mA

3.81

3.97

ns

8 mA

0.32

0.34

ns

6 mA

2.99

3.11

ns

12 mA

0.28

0.30

ns

2 mA

3.25

3.38

ns

16 mA

0.28

0.30

ns

4 mA

2.59

2.70

ns

2 mA

5.08

5.29

ns

LVCMOS15

Slow

Fast

LVCMOS12

6 mA

1.47

1.53

ns

Slow

2 mA

6.36

6.63

ns

Fast

2 mA

4.26

4.44

ns

4 mA

1.82

1.89

ns

6 mA

1.00

1.04

ns

8 mA

0.66

0.69

ns

HSTL_I_18

0.33

0.34

ns

12 mA

0.40

0.42

ns

HSTL_III_18

0.53

0.55

ns

16 mA

0.41

0.43

ns

PCI33_3

0.44

0.46

ns

2 mA

4.68

4.87

ns

PCI66_3

0.44

0.46

ns

4 mA

1.46

1.52

ns

SSTL18_I

0.24

0.25

ns

6 mA

0.38

0.39

ns

SSTL2_I

–0.20

–0.20

ns

8 mA

0.33

0.34

ns

Differential Standards

12 mA

0.28

0.30

ns

LVDS_25

–0.55

–0.55

ns

16 mA

0.28

0.30

ns

BLVDS_25

0.04

0.04

ns

2 mA

4.04

4.21

ns

MINI_LVDS_25

–0.56

–0.56

ns

4 mA

2.17

2.26

ns

LVPECL_25

6 mA

1.46

1.52

ns

RSDS_25

–0.48

–0.48

ns

8 mA

1.04

1.08

ns

DIFF_HSTL_I_18

0.42

0.42

ns

12 mA

0.65

0.68

ns

DIFF_HSTL_III_18

0.53

0.55

ns

0.40

0.40

ns

0.44

0.44

ns

2 mA

3.53

3.67

ns

DIFF_SSTL18_I

4 mA

1.65

1.72

ns

DIFF_SSTL2_I

6 mA

0.44

0.46

ns

Notes:

8 mA

0.20

0.21

ns

1.

12 mA

0

0

ns 2.

DS312 (v4.1) July 19, 2013 Product Specification

Slow

Add the Adjustment Below -5

-4

Single-Ended Standards LVTTL

Convert Output Time from LVCMOS25 with 12mA Drive and Fast Slew Rate to the Following Signal Standard (IOSTANDARD)

Input Only

ns

The numbers in this table are tested using the methodology presented in Table 95 and are based on the operating conditions set forth in Table 77, Table 80, and Table 82. These adjustments are used to convert output- and three-state-path times originally specified for the LVCMOS25 standard with 12 mA drive and Fast slew rate to times that correspond to other signal standards. Do not adjust times that measure when outputs go into a high-impedance state.

www.xilinx.com 131

Spartan-3E FPGA Family: DC and Switching Characteristics

Timing Measurement Methodology LVCMOS, LVTTL), then RT is set to 1MΩ to indicate an open connection, and VT is set to zero. The same measurement point (VM) that was used at the Input is also used at the Output.

When measuring timing parameters at the programmable I/Os, different signal standards call for different test conditions. Table 95 lists the conditions to use for each standard. The method for measuring Input timing is as follows: A signal that swings between a Low logic level of VL and a High logic level of VH is applied to the Input under test. Some standards also require the application of a bias voltage to the VREF pins of a given bank to properly set the input-switching threshold. The measurement point of the Input signal (VM) is commonly located halfway between VL and VH.

X-Ref Target - Figure 72

VT (VREF) FPGA Output

RT (RREF) VM (VMEAS) CL (CREF)

The Output test setup is shown in Figure 72. A termination voltage VT is applied to the termination resistor RT, the other end of which is connected to the Output. For each standard, RT and VT generally take on the standard values recommended for minimizing signal reflections. If the standard does not ordinarily use terminations (e.g.,

ds312-3_04_090105

Notes: 1.

The names shown in parentheses are used in the IBIS file.

Figure 72: Output Test Setup

Table 95: Test Methods for Timing Measurement at I/Os Signal Standard (IOSTANDARD)

Inputs

Inputs and Outputs

Outputs

VREF (V)

VL (V)

VH (V)

RT (Ω)

VT (V)

VM (V)

LVTTL

-

0

3.3

1M

0

1.4

LVCMOS33

-

0

3.3

1M

0

1.65

LVCMOS25

-

0

2.5

1M

0

1.25

LVCMOS18

-

0

1.8

1M

0

0.9

LVCMOS15

-

0

1.5

1M

0

0.75

LVCMOS12

-

0

1.2

1M

0

0.6

-

Note 3

Note 3

25

0

0.94

25

3.3

2.03

25

0

0.94

25

3.3

2.03

Single-Ended

PCI33_3

Rising Falling

PCI66_3

Rising

-

Note 3

Note 3

Falling HSTL_I_18

0.9

VREF – 0.5

VREF + 0.5

50

0.9

VREF

HSTL_III_18

1.1

VREF – 0.5

VREF + 0.5

50

1.8

VREF

SSTL18_I

0.9

VREF – 0.5

VREF + 0.5

50

0.9

VREF

SSTL2_I

1.25

VREF – 0.75

VREF + 0.75

50

1.25

VREF

LVDS_25

-

VICM – 0.125

VICM + 0.125

50

1.2

VICM

BLVDS_25

-

VICM – 0.125

VICM + 0.125

1M

0

VICM

MINI_LVDS_25

-

VICM – 0.125

VICM + 0.125

50

1.2

VICM

LVPECL_25

-

VICM – 0.3

VICM + 0.3

1M

0

VICM

RSDS_25

-

VICM – 0.1

VICM + 0.1

50

1.2

VICM

Differential

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 132

Spartan-3E FPGA Family: DC and Switching Characteristics Table 95: Test Methods for Timing Measurement at I/Os (Cont’d) Signal Standard (IOSTANDARD)

Inputs

Inputs and Outputs

Outputs

VREF (V)

VL (V)

VH (V)

RT (Ω)

VT (V)

VM (V)

DIFF_HSTL_I_18

-

VREF – 0.5

VREF + 0.5

50

0.9

VICM

DIFF_HSTL_III_18

-

VREF – 0.5

VREF + 0.5

50

1.8

VICM

DIFF_SSTL18_I

-

VREF – 0.5

VREF + 0.5

50

0.9

VICM

DIFF_SSTL2_I

-

VREF – 0.5

VREF + 0.5

50

1.25

VICM

Notes: 1.

2. 3.

Descriptions of the relevant symbols are as follows: VREF – The reference voltage for setting the input switching threshold VICM – The common mode input voltage VM – Voltage of measurement point on signal transition VL – Low-level test voltage at Input pin VH – High-level test voltage at Input pin RT – Effective termination resistance, which takes on a value of 1MΩ when no parallel termination is required VT – Termination voltage The load capacitance (CL) at the Output pin is 0 pF for all signal standards. According to the PCI specification.

The capacitive load (CL) is connected between the output and GND. The Output timing for all standards, as published in the speed files and the data sheet, is always based on a CL value of zero. High-impedance probes (less than 1 pF) are used for all measurements. Any delay that the test fixture might contribute to test measurements is subtracted from those measurements to produce the final timing numbers as published in the speed files and data sheet.

Using IBIS Models to Simulate Load Conditions in Application IBIS models permit the most accurate prediction of timing delays for a given application. The parameters found in the IBIS model (VREF, RREF, and VMEAS) correspond directly with the parameters used in Table 95 (VT, RT, and VM). Do not confuse VREF (the termination voltage) from the IBIS model with VREF (the input-switching threshold) from the table. A fourth parameter, CREF, is always zero. The four parameters describe all relevant output test conditions. IBIS models are found in the Xilinx development software as well as at the following link:

Delays for a given application are simulated according to its specific load conditions as follows: 1. Simulate the desired signal standard with the output driver connected to the test setup shown in Figure 72. Use parameter values VT, RT, and VM from Table 95. CREF is zero. 2. Record the time to VM. 3. Simulate the same signal standard with the output driver connected to the PCB trace with load. Use the appropriate IBIS model (including VREF, RREF, CREF, and VMEAS values) or capacitive value to represent the load. 4. Record the time to VMEAS. 5. Compare the results of steps 2 and 4. Add (or subtract) the increase (or decrease) in delay to (or from) the appropriate Output standard adjustment (Table 94) to yield the worst-case delay of the PCB trace.

http://www.xilinx.com/support/download/index.htm

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 133

Spartan-3E FPGA Family: DC and Switching Characteristics

Simultaneously Switching Output Guidelines This section provides guidelines for the recommended maximum allowable number of Simultaneous Switching Outputs (SSOs). These guidelines describe the maximum number of user I/O pins of a given output signal standard that should simultaneously switch in the same direction, while maintaining a safe level of switching noise. Meeting these guidelines for the stated test conditions ensures that the FPGA operates free from the adverse effects of ground and power bounce. Ground or power bounce occurs when a large number of outputs simultaneously switch in the same direction. The output drive transistors all conduct current to a common voltage rail. Low-to-High transitions conduct to the VCCO rail; High-to-Low transitions conduct to the GND rail. The resulting cumulative current transient induces a voltage difference across the inductance that exists between the die pad and the power supply or ground return. The inductance is associated with bonding wires, the package lead frame, and any other signal routing inside the package. Other variables contribute to SSO noise levels, including stray inductance on the PCB as well as capacitive loading at receivers. Any SSO-induced voltage consequently affects internal switching noise margins and ultimately signal quality. Table 96 and Table 97 provide the essential SSO guidelines. For each device/package combination, Table 96 provides the number of equivalent VCCO /GND pairs. The

equivalent number of pairs is based on characterization and might not match the physical number of pairs. For each output signal standard and drive strength, Table 97 recommends the maximum number of SSOs, switching in the same direction, allowed per VCCO /GND pair within an I/O bank. The guidelines in Table 97 are categorized by package style. Multiply the appropriate numbers from Table 96 and Table 97 to calculate the maximum number of SSOs allowed within an I/O bank. Exceeding these SSO guidelines might result in increased power or ground bounce, degraded signal integrity, or increased system jitter. SSOMAX/IO Bank = Table 96 x Table 97 The recommended maximum SSO values assumes that the FPGA is soldered on the printed circuit board and that the board uses sound design practices. The SSO values do not apply for FPGAs mounted in sockets, due to the lead inductance introduced by the socket. The number of SSOs allowed for quad-flat packages (VQ, TQ, PQ) is lower than for ball grid array packages (FG) due to the larger lead inductance of the quad-flat packages. The results for chip-scale packaging (CP132) are better than quad-flat packaging but not as high as for ball grid array packaging. Ball grid array packages are recommended for applications with a large number of simultaneously switching outputs.

Table 96: Equivalent VCCO/GND Pairs per Bank Device

Package Style (including Pb-free) VQ100

CP132

TQ144

PQ208

FT256

FG320

FG400

FG484

XC3S100E

2

2

2

-

-

-

-

-

XC3S250E

2

2

2

3

4

-

-

-

XC3S500E

2

2

-

3

4

5

-

-

XC3S1200E

-

-

-

-

4

5

6

-

XC3S1600E

-

-

-

-

-

5

6

7

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 134

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 97: Recommended Number of Simultaneously Switching Outputs per VCCO /GND Pair

Table 97: Recommended Number of Simultaneously Switching Outputs per VCCO /GND Pair (Cont’d) Package Type

Package Type Signal Standard (IOSTANDARD)

VQ 100

TQ 144

PQ 208

CP 132

VQ 100

TQ 144

PQ 208

CP 132

FT256 FG320 FG400 FG484

2

16

10

10

19

55

60

4

8

7

7

9

31

6

6

5

5

9

18

2

9

9

9

13

25

4

7

7

7

7

16 13

FT256 FG320 FG400 FG484

LVCMOS15

Single-Ended Standards LVTTL

Slow

2

Fast

LVCMOS33

Slow

LVCMOS25

Slow

Fast

LVCMOS18

Slow

Fast

20

19

52

17

10

10

26

41

6

17

10

7

26

29

8

8

6

6

13

22

12

8

6

5

13

13

5

5

5

6

11

Slow

Fast

LVCMOS12

6

5

5

5

5

Slow

2

17

11

11

16

55

Fast

2

10

10

10

10

31

2

17

17

17

26

34

4

9

9

9

13

20

PCI33_3

8

8

8

16

16

8

8

8

13

13

6

7

7

7

13

15

PCI66_3

8

6

6

6

6

12

PCIX

7

7

7

11

11

10

10

10

16

17

12

5

5

5

6

10

HSTL_I_18

16

5

5

5

5

9

HSTL_III_18

10

10

10

16

16

9

9

9

15

15

12

12

12

18

18

2

34

20

20

52

76

SSTL18_I

4

17

10

10

26

46

SSTL2_I

6

17

10

7

26

27

Differential Standards (Number of I/O Pairs or Channels)

8

8

6

6

13

20

LVDS_25

6

6

6

12

20

13

BLVDS_25

4

4

4

4

4

6

6

6

12

20

12 Fast

34

4

16

Signal Standard (IOSTANDARD)

8

6

5

13

16

5

5

5

6

10

MINI_LVDS_25

2

17

17

17

26

44

LVPECL_25

4

8

8

8

13

26

RSDS_25

6

6

6

12

20

6

8

6

6

13

16

DIFF_HSTL_I_18

5

5

5

8

8

5

5

5

8

8

Input Only

8

6

6

6

6

12

DIFF_HSTL_IIII_18

12

5

5

5

6

10

DIFF_SSTL18_I

4

4

4

7

7

6

6

6

9

8

16

8

8

5

5

8

DIFF_SSTL2_I

2

28

16

16

42

76

Notes:

4

13

10

10

19

46

1.

6

13

7

7

19

33 24

8

6

6

6

9

12

6

6

6

9

18

2

17

16

16

26

42

4

9

9

9

13

20

6

9

7

7

13

15

8

6

6

6

6

13

12

5

5

5

6

11

2

19

11

8

29

64

4

13

7

6

19

34

6

6

5

5

9

22

8

6

4

4

9

18

2

13

8

8

19

36

4

8

5

5

13

21

6

4

4

4

6

13

8

4

4

4

6

10

DS312 (v4.1) July 19, 2013 Product Specification

2.

3.

The numbers in this table are recommendations that assume sound board layout practice. This table assumes the following parasitic factors: combined PCB trace and land inductance per VCCO and GND pin of 1.0 nH, receiver capacitive load of 15 pF. Test limits are the VIL/VIH voltage limits for the respective I/O standard. The PQ208 results are based on physical measurements of a PQ208 package soldered to a typical printed circuit board. All other results are based on worst-case simulation and an interpolation of the PQ208 physical results. If more than one signal standard is assigned to the I/Os of a given bank, refer to XAPP689: Managing Ground Bounce in Large FPGAs for information on how to perform weighted average SSO calculations.

www.xilinx.com 135

Spartan-3E FPGA Family: DC and Switching Characteristics

Configurable Logic Block (CLB) Timing Table 98: CLB (SLICEM) Timing Speed Grade Symbol

Description

-5

-4

Units

Min

Max

Min

Max

When reading from the FFX (FFY) Flip-Flop, the time from the active transition at the CLK input to data appearing at the XQ (YQ) output

-

0.52

-

0.60

ns

TAS

Time from the setup of data at the F or G input to the active transition at the CLK input of the CLB

0.46

-

0.52

-

ns

TDICK

Time from the setup of data at the BX or BY input to the active transition at the CLK input of the CLB

1.58

-

1.81

-

ns

TAH

Time from the active transition at the CLK input to the point where data is last held at the F or G input

0

-

0

-

ns

TCKDI

Time from the active transition at the CLK input to the point where data is last held at the BX or BY input

0

-

0

-

ns

Clock-to-Output Times TCKO

Setup Times

Hold Times

Clock Timing TCH

The High pulse width of the CLB’s CLK signal

0.70

-

0.80

-

ns

TCL

The Low pulse width of the CLK signal

0.70

-

0.80

-

ns

FTOG

Toggle frequency (for export control)

0

657

0

572

MHz

The time it takes for data to travel from the CLB’s F (G) input to the X (Y) output

-

0.66

-

0.76

ns

1.57

-

1.80

-

ns

Propagation Times TILO

Set/Reset Pulse Width TRPW_CLB

The minimum allowable pulse width, High or Low, to the CLB’s SR input

Notes: 1.

The numbers in this table are based on the operating conditions set forth in Table 77.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 136

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 99: CLB Distributed RAM Switching Characteristics Symbol

-5

Description

-4

Units

Min

Max

Min

Max

-

2.05

-

2.35

ns

Clock-to-Output Times TSHCKO

Time from the active edge at the CLK input to data appearing on the distributed RAM output

Setup Times TDS

Setup time of data at the BX or BY input before the active transition at the CLK input of the distributed RAM

0.40

-

0.46

-

ns

TAS

Setup time of the F/G address inputs before the active transition at the CLK input of the distributed RAM

0.46

-

0.52

-

ns

TWS

Setup time of the write enable input before the active transition at the CLK input of the distributed RAM

0.34

-

0.40

-

ns

TDH

Hold time of the BX, BY data inputs after the active transition at the CLK input of the distributed RAM

0.13

-

0.15

-

ns

TAH, TWH

Hold time of the F/G address inputs or the write enable input after the active transition at the CLK input of the distributed RAM

0

-

0

-

ns

0.88

-

1.01

-

ns

Hold Times

Clock Pulse Width TWPH, TWPL

Minimum High or Low pulse width at CLK input

Table 100: CLB Shift Register Switching Characteristics Symbol

-5

Description

-4

Units

Min

Max

Min

Max

-

3.62

-

4.16

ns

Setup time of data at the BX or BY input before the active transition at the CLK input of the shift register

0.41

-

0.46

-

ns

Hold time of the BX or BY data input after the active transition at the CLK input of the shift register

0.14

-

0.16

-

ns

0.88

-

1.01

-

ns

Clock-to-Output Times TREG

Time from the active edge at the CLK input to data appearing on the shift register output

Setup Times TSRLDS

Hold Times TSRLDH

Clock Pulse Width TWPH, TWPL

Minimum High or Low pulse width at CLK input

Clock Buffer/Multiplexer Switching Characteristics Table 101: Clock Distribution Switching Characteristics Maximum Description

Symbol

Speed Grade -5

-4

Units

Global clock buffer (BUFG, BUFGMUX, BUFGCE) I input to O-output delay

TGIO

1.46

1.46

ns

Global clock multiplexer (BUFGMUX) select S-input setup to I0 and I1 inputs. Same as BUFGCE enable CE-input

TGSI

0.55

0.63

ns

FBUFG

333

311

MHz

Frequency of signals distributed on global buffers (all sides)

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 137

Spartan-3E FPGA Family: DC and Switching Characteristics

18 x 18 Embedded Multiplier Timing Table 102: 18 x 18 Embedded Multiplier Timing Speed Grade Symbol

Description

-5 Min

-4 Max

Units

Min

Max

Combinatorial Delay TMULT

Combinatorial multiplier propagation delay from the A and B inputs to the P outputs, assuming 18-bit inputs and a 36-bit product (AREG, BREG, and PREG registers unused)

-

4.34(1)

-

4.88(1)

ns

Clock-to-Output Times TMSCKP_P

Clock-to-output delay from the active transition of the CLK input to valid data appearing on the P outputs when using the PREG register(2)

-

0.98

-

1.10

ns

TMSCKP_A TMSCKP_B

Clock-to-output delay from the active transition of the CLK input to valid data appearing on the P outputs when using either the AREG or BREG register(3)

-

4.42

-

4.97

ns

TMSDCK_P

Data setup time at the A or B input before the active transition at the CLK when using only the PREG output register (AREG, BREG registers unused)(2)

3.54

-

3.98

-

ns

TMSDCK_A

Data setup time at the A input before the active transition at the CLK when using the AREG input register(3)

0.20

-

0.23

-

ns

TMSDCK_B

Data setup time at the B input before the active transition at the CLK when using the BREG input register(3)

0.35

-

0.39

-

ns

TMSCKD_P

Data hold time at the A or B input after the active transition at the CLK when using only the PREG output register (AREG, BREG registers unused)(2)

–0.97

-

–0.97

-

ns

TMSCKD_A

Data hold time at the A input after the active transition at the CLK when using the AREG input register(3)

0.03

-

0.04

-

ns

TMSCKD_B

Data hold time at the B input after the active transition at the CLK when using the BREG input register(3)

0.04

-

0.05

-

ns

0

270

0

240

MHz

Setup Times

Hold Times

Clock Frequency FMULT

Internal operating frequency for a two-stage 18x18 multiplier using the AREG and BREG input registers and the PREG output register(1)

Notes: 1. 2. 3.

Combinatorial delay is less and pipelined performance is higher when multiplying input data with less than 18 bits. The PREG register is typically used in both single-stage and two-stage pipelined multiplier implementations. Input registers AREG or BREG are typically used when inferring a two-stage multiplier.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 138

Spartan-3E FPGA Family: DC and Switching Characteristics

Block RAM Timing Table 103: Block RAM Timing Speed Grade Symbol

Description

-5

-4

Units

Min

Max

Min

Max

-

2.45

-

2.82

ns

Clock-to-Output Times TBCKO

When reading from block RAM, the delay from the active transition at the CLK input to data appearing at the DOUT output

Setup Times TBACK

Setup time for the ADDR inputs before the active transition at the CLK input of the block RAM

0.33

-

0.38

-

ns

TBDCK

Setup time for data at the DIN inputs before the active transition at the CLK input of the block RAM

0.23

-

0.23

-

ns

TBECK

Setup time for the EN input before the active transition at the CLK input of the block RAM

0.67

-

0.77

-

ns

TBWCK

Setup time for the WE input before the active transition at the CLK input of the block RAM

1.09

-

1.26

-

ns

TBCKA

Hold time on the ADDR inputs after the active transition at the CLK input

0.12

-

0.14

-

ns

TBCKD

Hold time on the DIN inputs after the active transition at the CLK input

0.12

-

0.13

-

ns

TBCKE

Hold time on the EN input after the active transition at the CLK input

0

-

0

-

ns

TBCKW

Hold time on the WE input after the active transition at the CLK input

0

-

0

-

ns

Hold Times

Clock Timing TBPWH

High pulse width of the CLK signal

1.39

-

1.59

-

ns

TBPWL

Low pulse width of the CLK signal

1.39

-

1.59

-

ns

0

270

0

230

MHz

Clock Frequency FBRAM

Block RAM clock frequency. RAM read output value written back into RAM, for shift-registers and circular buffers. Write-only or read-only performance is faster.

Notes: 1.

The numbers in this table are based on the operating conditions set forth in Table 77.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 139

Spartan-3E FPGA Family: DC and Switching Characteristics

Digital Clock Manager (DCM) Timing For specification purposes, the DCM consists of three key components: the Delay-Locked Loop (DLL), the Digital Frequency Synthesizer (DFS), and the Phase Shifter (PS).

Period jitter is the worst-case deviation from the ideal clock period over a collection of millions of samples. In a histogram of period jitter, the mean value is the clock period.

Aspects of DLL operation play a role in all DCM applications. All such applications inevitably use the CLKIN and the CLKFB inputs connected to either the CLK0 or the CLK2X feedback, respectively. Thus, specifications in the DLL tables (Table 104 and Table 105) apply to any application that only employs the DLL component. When the DFS and/or the PS components are used together with the DLL, then the specifications listed in the DFS and PS tables (Table 106 through Table 109) supersede any corresponding ones in the DLL tables. DLL specifications that do not change with the addition of DFS or PS functions are presented in Table 104 and Table 105.

Cycle-cycle jitter is the worst-case difference in clock period between adjacent clock cycles in the collection of clock periods sampled. In a histogram of cycle-cycle jitter, the mean value is zero.

Spread Spectrum DCMs accept typical spread spectrum clocks as long as they meet the input requirements. The DLL will track the frequency changes created by the spread spectrum clock to drive the global clocks to the FPGA logic. See XAPP469, Spread-Spectrum Clocking Reception for Displays for details.

Period jitter and cycle-cycle jitter are two of many different ways of specifying clock jitter. Both specifications describe statistical variation from a mean value.

Delay-Locked Loop (DLL) Table 104: Recommended Operating Conditions for the DLL Speed Grade Symbol

Description

-5

-4

Units

Min

Max

Min

Max

N/A

N/A

5(2)

90(3)

MHz

200(3)

MHz

240(3)

MHz

Input Frequency Ranges FCLKIN CLKIN_FREQ_DLL

Frequency of the CLKIN clock input

Stepping 0

XC3S100E XC3S250E XC3S500E XC3S1600E XC3S1200E(3)

5(2)

275(3)

FCLKIN ≤ 150 MHz

40%

60%

40%

60%

-

FCLKIN > 150 MHz

45%

55%

45%

55%

-

FCLKIN ≤ 150 MHz

-

±300

-

±300

ps

FCLKIN > 150 MHz

-

±150

-

±150

ps

Stepping 1

All

Input Pulse Requirements CLKIN_PULSE

CLKIN pulse width as a percentage of the CLKIN period

Input Clock Jitter Tolerance and Delay Path Variation(4) CLKIN_CYC_JITT_DLL_LF CLKIN_CYC_JITT_DLL_HF

Cycle-to-cycle jitter at the CLKIN input

CLKIN_PER_JITT_DLL

Period jitter at the CLKIN input

-

±1

-

±1

ns

CLKFB_DELAY_VAR_EXT

Allowable variation of off-chip feedback delay from the DCM output to the CLKFB input

-

±1

-

±1

ns

Notes: 1. 2. 3. 4.

DLL specifications apply when any of the DLL outputs (CLK0, CLK90, CLK180, CLK270, CLK2X, CLK2X180, or CLKDV) are in use. The DFS, when operating independently of the DLL, supports lower FCLKIN frequencies. See Table 106. To support double the maximum effective FCLKIN limit, set the CLKIN_DIVIDE_BY_2 attribute to TRUE. This attribute divides the incoming clock frequency by two as it enters the DCM. The CLK2X output reproduces the clock frequency provided on the CLKIN input. CLKIN input jitter beyond these limits might cause the DCM to lose lock.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 140

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 105: Switching Characteristics for the DLL Speed Grade Symbol

Description

Device

-5

-4

Units

Min

Max

Min

Max

N/A

N/A

5

90

MHz

200

MHz

240

MHz

90

MHz

167

MHz

200

MHz

180

MHz

311

MHz

311

MHz

60

MHz

133

MHz

160

MHz

Output Frequency Ranges CLKOUT_FREQ_CLK0

Frequency for the CLK0 and CLK180 outputs

Stepping 0

XC3S100E XC3S250E XC3S500E XC3S1600E XC3S1200E

CLKOUT_FREQ_CLK90

Frequency for the CLK90 and CLK270 outputs

Stepping 1

All

5

275

Stepping 0

XC3S100E XC3S250E XC3S500E XC3S1600E

N/A

N/A

5

XC3S1200E

CLKOUT_FREQ_2X

Frequency for the CLK2X and CLK2X180 outputs

Stepping 1

All

5

200

Stepping 0

XC3S100E XC3S250E XC3S500E XC3S1600E

N/A

N/A

10

XC3S1200E

CLKOUT_FREQ_DV

Frequency for the CLKDV output

Stepping 1

All

10

333

Stepping 0

XC3S100E XC3S250E XC3S500E XC3S1600E

N/A

N/A

0.3125

XC3S1200E Stepping 1

Output Clock

All

0.3125

183

All

-

±100

-

±100

ps

Jitter (2,3,4)

CLKOUT_PER_JITT_0

Period jitter at the CLK0 output

CLKOUT_PER_JITT_90

Period jitter at the CLK90 output

-

±150

-

±150

ps

CLKOUT_PER_JITT_180

Period jitter at the CLK180 output

-

±150

-

±150

ps

CLKOUT_PER_JITT_270

Period jitter at the CLK270 output

-

±150

-

±150

ps

CLKOUT_PER_JITT_2X

Period jitter at the CLK2X and CLK2X180 outputs

-

±[1% of CLKIN period + 150]

-

±[1% of CLKIN period + 150]

ps

CLKOUT_PER_JITT_DV1

Period jitter at the CLKDV output when performing integer division

-

±150

-

±150

ps

CLKOUT_PER_JITT_DV2

Period jitter at the CLKDV output when performing non-integer division

-

±[1% of CLKIN period + 200]

-

±[1% of CLKIN period + 200]

ps

-

±[1% of CLKIN period + 400]

-

±[1% of CLKIN period + 400]

ps

Duty Cycle(4) CLKOUT_DUTY_CYCLE_DLL Duty cycle variation for the CLK0, CLK90, CLK180, CLK270, CLK2X, CLK2X180, and CLKDV outputs, including the BUFGMUX and clock tree duty-cycle distortion

DS312 (v4.1) July 19, 2013 Product Specification

All

www.xilinx.com 141

Spartan-3E FPGA Family: DC and Switching Characteristics Table 105: Switching Characteristics for the DLL (Cont’d) Speed Grade Symbol

Phase

Description

Device

-5

-4

Units

Min

Max

Min

Max

-

±200

-

±200

ps

CLK0 to CLK2X (not CLK2X180)

-

±[1% of CLKIN period + 100]

-

±[1% of CLKIN period + 100]

ps

All others

-

±[1% of CLKIN period + 200]

-

±[1% of CLKIN period + 200]

ps

-

5

-

5

ms

-

600

-

600

μs

20

40

20

40

ps

Alignment(4)

CLKIN_CLKFB_PHASE

Phase offset between the CLKIN and CLKFB inputs

CLKOUT_PHASE_DLL

Phase offset between DLL outputs

All

Lock Time LOCK_DLL(3)

When using the DLL alone: The time from deassertion at the DCM’s Reset input to the rising transition at its LOCKED output. When the DCM is locked, the CLKIN and CLKFB signals are in phase

5 MHz ≤ FCLKIN ≤ 15 MHz

All

FCLKIN > 15 MHz

Delay Lines DCM_DELAY_STEP

Finest delay resolution

All

Notes: 1. 2. 3. 4.

The numbers in this table are based on the operating conditions set forth in Table 77 and Table 104. Indicates the maximum amount of output jitter that the DCM adds to the jitter on the CLKIN input. For optimal jitter tolerance and faster lock time, use the CLKIN_PERIOD attribute. Some jitter and duty-cycle specifications include 1% of input clock period or 0.01 UI. Example: The data sheet specifies a maximum jitter of ±[1% of CLKIN period + 150]. Assume the CLKIN frequency is 100 MHz. The equivalent CLKIN period is 10 ns and 1% of 10 ns is 0.1 ns or 100 ps. According to the data sheet, the maximum jitter is ±[100 ps + 150 ps] = ±250 ps.

Digital Frequency Synthesizer (DFS) Table 106: Recommended Operating Conditions for the DFS Speed Grade Symbol

Description

-5 Min

Input Frequency FCLKIN

-4 Max

Min

Units Max

Ranges(2)

CLKIN_FREQ_FX

Input Clock Jitter

Frequency for the CLKIN input

0.200

333(4)

0.200

333(4)

MHz

Tolerance(3)

CLKIN_CYC_JITT_FX_LF CLKIN_CYC_JITT_FX_HF

Cycle-to-cycle jitter at the CLKIN input, based on CLKFX output frequency

CLKIN_PER_JITT_FX

Period jitter at the CLKIN input

FCLKFX ≤ 150 MHz

-

±300

-

±300

ps

FCLKFX > 150 MHz

-

±150

-

±150

ps

-

±1

-

±1

ns

Notes: 1. 2. 3. 4.

DFS specifications apply when either of the DFS outputs (CLKFX or CLKFX180) are used. If both DFS and DLL outputs are used on the same DCM, follow the more restrictive CLKIN_FREQ_DLL specifications in Table 104. CLKIN input jitter beyond these limits may cause the DCM to lose lock. To support double the maximum effective FCLKIN limit, set the CLKIN_DIVIDE_BY_2 attribute to TRUE. This attribute divides the incoming clock frequency by two as it enters the DCM.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 142

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 107: Switching Characteristics for the DFS Speed Grade Symbol

Description

Device

-5

-4

Units

Min

Max

Min

Max

N/A

N/A

5

90

MHz

220

307

MHz

5

307

MHz

311

MHz

Output Frequency Ranges CLKOUT_FREQ_FX_LF

Frequency for the CLKFX and CLKFX180 outputs, low frequencies

CLKOUT_FREQ_FX_HF

Frequency for the CLKFX and CLKFX180 outputs, high frequencies

CLKOUT_FREQ_FX

Frequency for the CLKFX and CLKFX180 outputs

Stepping 0

XC3S100E XC3S250E XC3S500E XC3S1600E

Stepping 0

XC3S1200E

Stepping 1

All

5

333

All

Typ

Max

Output Clock Jitter(2,3) CLKOUT_PER_JITT_FX

Period jitter at the CLKFX and CLKFX180 outputs.

Typ

Max

CLKIN ≤ 20 MHz

Note 6

ps

CLKIN > 20 MHz

±[1% of ±[1% of ±[1% of ±[1% of CLKFX CLKFX CLKFX CLKFX period period period period + 100] + 200] + 100] + 200]

ps

Duty Cycle(4,5) CLKOUT_DUTY_CYCLE_FX Duty cycle precision for the CLKFX and CLKFX180 outputs, including the BUFGMUX and clock tree duty-cycle distortion

All

-

±[1% of CLKFX period + 400]

-

±[1% of CLKFX period + 400]

ps

Phase Alignment(5) CLKOUT_PHASE_FX

Phase offset between the DFS CLKFX output and the DLL CLK0 output when both the DFS and DLL are used

All

-

±200

-

±200

ps

CLKOUT_PHASE_FX180

Phase offset between the DFS CLKFX180 output and the DLL CLK0 output when both the DFS and DLL are used

All

-

±[1% of CLKFX period + 300]

-

±[1% of CLKFX period + 300]

ps

All

-

5

-

5

ms

-

450

-

450

μs

Lock Time LOCK_FX(2)

The time from deassertion at the DCM’s Reset input to the rising transition at its LOCKED output. The DFS asserts LOCKED when the CLKFX and CLKFX180 signals are valid. If using both the DLL and the DFS, use the longer locking time.

5 MHz ≤ FCLKIN ≤ 15 MHz FCLKIN > 15 MHz

Notes: 1. 2. 3.

4. 5.

6.

The numbers in this table are based on the operating conditions set forth in Table 77 and Table 106. For optimal jitter tolerance and faster lock time, use the CLKIN_PERIOD attribute. Maximum output jitter is characterized within a reasonable noise environment (150 ps input period jitter, 40 SSOs and 25% CLB switching). Output jitter strongly depends on the environment, including the number of SSOs, the output drive strength, CLB utilization, CLB switching activities, switching frequency, power supply and PCB design. The actual maximum output jitter depends on the system application. The CLKFX and CLKFX180 outputs always have an approximate 50% duty cycle. Some duty-cycle and alignment specifications include 1% of the CLKFX output period or 0.01 UI. Example: The data sheet specifies a maximum jitter of ±[1% of CLKFX period + 300]. Assume the CLKFX output frequency is 100 MHz. The equivalent CLKFX period is 10 ns and 1% of 10 ns is 0.1 ns or 100 ps. According to the data sheet, the maximum jitter is ±[100 ps + 300 ps] = ±400 ps. Use the Spartan-3A Jitter Calculator (www.xilinx.com/support/documentation/data_sheets/s3a_jitter_calc.zip) to estimate DFS output jitter. Use the Clocking Wizard to determine jitter for a specific design.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 143

Spartan-3E FPGA Family: DC and Switching Characteristics

Phase Shifter (PS) Table 108: Recommended Operating Conditions for the PS in Variable Phase Mode Speed Grade Symbol

Description

-5

-4

Units

Min

Max

Min

Max

1

167

1

167

MHz

40%

60%

40%

60%

-

Operating Frequency Ranges PSCLK_FREQ (FPSCLK)

Frequency for the PSCLK input

Input Pulse Requirements PSCLK_PULSE

PSCLK pulse width as a percentage of the PSCLK period

Table 109: Switching Characteristics for the PS in Variable Phase Mode Symbol

Description

Equation

Units

Phase Shifting Range MAX_STEPS(2)

Maximum allowed number of DCM_DELAY_STEP steps for a given CLKIN clock period, where T = CLKIN clock period in ns. If using CLKIN_DIVIDE_BY_2 = TRUE, double the effective clock period.(3)

CLKIN < 60 MHz

±[INTEGER(10 • (TCLKIN – 3 ns))]

steps

CLKIN ≥ 60 MHz

±[INTEGER(15 • (TCLKIN – 3 ns))]

steps

FINE_SHIFT_RANGE_MIN

Minimum guaranteed delay for variable phase shifting

±[MAX_STEPS • DCM_DELAY_STEP_MIN]

ns

FINE_SHIFT_RANGE_MAX

Maximum guaranteed delay for variable phase shifting

±[MAX_STEPS • DCM_DELAY_STEP_MAX]

ns

Notes: 1. 2. 3.

The numbers in this table are based on the operating conditions set forth in Table 77 and Table 108. The maximum variable phase shift range, MAX_STEPS, is only valid when the DCM is has no initial fixed phase shifting, i.e., the PHASE_SHIFT attribute is set to 0. The DCM_DELAY_STEP values are provided at the bottom of Table 105.

Miscellaneous DCM Timing Table 110: Miscellaneous DCM Timing Symbol

Min

Max

Units

Minimum duration of a RST pulse width

3

-

CLKIN cycles

DCM_RST_PW_MAX(2)

Maximum duration of a RST pulse width

N/A

N/A

seconds

DCM_CONFIG_LAG_TIME(3)

Maximum duration from VCCINT applied to FPGA configuration successfully completed (DONE pin goes High) and clocks applied to DCM DLL

N/A

N/A

minutes

DCM_RST_PW_MIN(1)

Description

Notes: 1. 2. 3.

This limit only applies to applications that use the DCM DLL outputs (CLK0, CLK90, CLK180, CLK270, CLK2X, CLK2X180, and CLKDV). The DCM DFS outputs (CLKFX, CLKFX180) are unaffected. This specification is equivalent to the Virtex-4 DCM_RESET specfication.This specification does not apply for Spartan-3E FPGAs. This specification is equivalent to the Virtex-4 TCONFIG specification. This specification does not apply for Spartan-3E FPGAs.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 144

Spartan-3E FPGA Family: DC and Switching Characteristics

Configuration and JTAG Timing General Configuration Power-On/Reconfigure Timing X-Ref Target - Figure 73

1.2V

VCCINT (Supply)

1.0V

VCCAUX (Supply)

2.0V

VCCO Bank 2 (Supply)

1.0V

2.5V

TPOR

PROG_B (Input) TPROG

INIT_B (Open-Drain)

TPL

TICCK

CCLK (Output) DS312-3_01_103105

Notes: 1. 2. 3.

The VCCINT, VCCAUX, and VCCO supplies may be applied in any order. The Low-going pulse on PROG_B is optional after power-on but necessary for reconfiguration without a power cycle. The rising edge of INIT_B samples the voltage levels applied to the mode pins (M0 - M2).

Figure 73: Waveforms for Power-On and the Beginning of Configuration Table 111: Power-On Timing and the Beginning of Configuration Symbol TPOR(2)

Description

Device

The time from the application of VCCINT, VCCAUX, and VCCO Bank 2 supply voltage ramps (whichever occurs last) to the rising transition of the INIT_B pin

TPROG

The width of the low-going pulse on the PROG_B pin

TPL(2)

The time from the rising edge of the PROG_B pin to the rising transition on the INIT_B pin

All Speed Grades

Units

Min

Max

XC3S100E

-

5

ms

XC3S250E

-

5

ms

XC3S500E

-

5

ms

XC3S1200E

-

5

ms

XC3S1600E

-

7

ms

All

0.5

-

μs

XC3S100E

-

0.5

ms

XC3S250E

-

0.5

ms

XC3S500E

-

1

ms

XC3S1200E

-

2

ms

XC3S1600E

-

2

ms

TINIT

Minimum Low pulse width on INIT_B output

All

250

-

ns

TICCK(3)

The time from the rising edge of the INIT_B pin to the generation of the configuration clock signal at the CCLK output pin

All

0.5

4.0

μs

Notes: 1. 2. 3.

The numbers in this table are based on the operating conditions set forth in Table 77. This means power must be applied to all VCCINT, VCCO, and VCCAUX lines. Power-on reset and the clearing of configuration memory occurs during this period. This specification applies only to the Master Serial, SPI, BPI-Up, and BPI-Down modes.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 145

Spartan-3E FPGA Family: DC and Switching Characteristics

Configuration Clock (CCLK) Characteristics Table 112: Master Mode CCLK Output Period by ConfigRate Option Setting Symbol TCCLK1

Description CCLK clock period by ConfigRate setting

ConfigRate Setting

Temperature Range

Minimum

1 (power-on value and default value)

Commercial

570

Industrial

485

Commercial

285

3

TCCLK3 TCCLK6

6

TCCLK12

12

TCCLK25

25

TCCLK50

50

Industrial

242

Commercial

142

Industrial

121

Commercial

71.2

Industrial

60.6

Commercial

35.5

Industrial

30.3

Commercial

17.8

Industrial

15.1

Maximum

Units ns

1,250

ns ns

625

ns ns

313

ns ns

157

ns ns

78.2

ns ns

39.1

ns

Notes: 1.

Set the ConfigRate option value when generating a configuration bitstream. See Bitstream Generator (BitGen) Options in Module 2.

Table 113: Master Mode CCLK Output Frequency by ConfigRate Option Setting Symbol FCCLK1

Description

ConfigRate Setting

Temperature Range

Equivalent CCLK clock frequency by ConfigRate setting

1 (power-on value and default value)

Commercial

FCCLK3

6

FCCLK12

12

FCCLK25

25

FCCLK50

50

Maximum

Units

1.8

MHz

2.1

MHz

3.6

MHz

0.8

Industrial Commercial

3

FCCLK6

Minimum

1.6

Industrial Commercial

3.2

Industrial Commercial

6.4

Industrial Commercial

12.8

Industrial Commercial

25.6

Industrial

4.2

MHz

7.1

MHz

8.3

MHz

14.1

MHz

16.5

MHz

28.1

MHz

33.0

MHz

56.2

MHz

66.0

MHz

Table 114: Master Mode CCLK Output Minimum Low and High Time Symbol TMCCL, TMCCH

ConfigRate Setting

Description Master mode CCLK minimum Low and High time

Units

1

3

6

12

25

50

Commercial

276

138

69

34.5

17.1

8.5

ns

Industrial

235

117

58

29.3

14.5

7.3

ns

Table 115: Slave Mode CCLK Input Low and High Time Symbol TSCCL, TSCCH

Description CCLK Low and High time

DS312 (v4.1) July 19, 2013 Product Specification

Min

Max

Units

5



ns

www.xilinx.com 146

Spartan-3E FPGA Family: DC and Switching Characteristics

Master Serial and Slave Serial Mode Timing X-Ref Target - Figure 74

PROG_B (Input)

INIT_B (Open-Drain)

TMCCH TSCCH

TMCCL TSCCL

CCLK (Input/Output) TDCC DIN (Input)

1/FCCSER

TCCD Bit 0

Bit 1

Bit n

Bit n+1 TCCO

DOUT (Output)

Bit n-64

Bit n-63 DS312-3_05_103105

Figure 74: Waveforms for Master Serial and Slave Serial Configuration Table 116: Timing for the Master Serial and Slave Serial Configuration Modes Symbol

Slave/ Master

Description

All Speed Grades

Units

Min

Max

Both

1.5

10.0

ns

The time from the setup of data at the DIN pin to the active edge of the CCLK pin

Both

11.0

-

ns

The time from the active edge of the CCLK pin to the point when data is last held at the DIN pin

Both

0

-

ns

Clock-to-Output Times TCCO

The time from the falling transition on the CCLK pin to data appearing at the DOUT pin

Setup Times TDCC

Hold Times TCCD

Clock Timing TCCH TCCL FCCSER

High pulse width at the CCLK input pin

Low pulse width at the CCLK input pin

Frequency of the clock signal at the CCLK input pin

No bitstream compression With bitstream compression

Master

See Table 114

Slave

See Table 115

Master

See Table 114

Slave

See Table 115

Slave

0

66(2)

MHz

0

20

MHz

Notes: 1. 2.

The numbers in this table are based on the operating conditions set forth in Table 77. For serial configuration with a daisy-chain of multiple FPGAs, the maximum limit is 25 MHz.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 147

Spartan-3E FPGA Family: DC and Switching Characteristics

Slave Parallel Mode Timing X-Ref Target - Figure 75

PROG_B (Input)

INIT_B (Open-Drain) TSMCSCC

TSMCCCS

CSI_B (Input) TSMCCW

TSMWCC

RDWR_B (Input) TMCCH TSCCH

TMCCL TSCCL

CCLK (Input) TSMDCC D0 - D7 (Inputs)

1/FCCPAR

TSMCCD

Byte 0

Byte 1

Byte n TSMCKBY

Byte n+1

TSMCKBY

High-Z

BUSY (Output)

High-Z BUSY DS312-3_02_103105

Notes: 1.

It is possible to abort configuration by pulling CSI_B Low in a given CCLK cycle, then switching RDWR_B Low or High in any subsequent cycle for which CSI_B remains Low. The RDWR_B pin asynchronously controls the driver impedance of the D0 - D7 bus. When RDWR_B switches High, be careful to avoid contention on the D0 - D7 bus.

Figure 75: Waveforms for Slave Parallel Configuration Table 117: Timing for the Slave Parallel Configuration Mode Symbol

Description

All Speed Grades

Units

Min

Max

-

12.0

ns

Clock-to-Output Times TSMCKBY

The time from the rising transition on the CCLK pin to a signal transition at the BUSY pin

Setup Times TSMDCC

The time from the setup of data at the D0-D7 pins to the active edge the CCLK pin

11.0

-

ns

TSMCSCC

Setup time on the CSI_B pin before the active edge of the CCLK pin

10.0

-

ns

TSMCCW(2)

Setup time on the RDWR_B pin before active edge of the CCLK pin

23.0

-

ns

TSMCCD

The time from the active edge of the CCLK pin to the point when data is last held at the D0-D7 pins

1.0

-

ns

TSMCCCS

The time from the active edge of the CCLK pin to the point when a logic level is last held at the CSO_B pin

0

-

ns

TSMWCC

The time from the active edge of the CCLK pin to the point when a logic level is last held at the RDWR_B pin

0

-

ns

Hold Times

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 148

Spartan-3E FPGA Family: DC and Switching Characteristics Table 117: Timing for the Slave Parallel Configuration Mode (Cont’d) Symbol

All Speed Grades

Description

Units

Min

Max

5

-

ns

5

-

ns

0

50

MHz

0

66

MHz

0

20

MHz

Clock Timing TCCH

The High pulse width at the CCLK input pin

TCCL

The Low pulse width at the CCLK input pin

FCCPAR

Frequency of the clock signal No bitstream at the CCLK input pin compression

Not using the BUSY Using the BUSY pin

With bitstream compression

pin(2)

Notes: 1. 2. 3.

The numbers in this table are based on the operating conditions set forth in Table 77. In the Slave Parallel mode, it is necessary to use the BUSY pin when the CCLK frequency exceeds this maximum specification. Some Xilinx documents refer to Parallel modes as “SelectMAP” modes.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 149

Spartan-3E FPGA Family: DC and Switching Characteristics

Serial Peripheral Interface (SPI) Configuration Timing X-Ref Target - Figure 76

PROG_B (Input)

HSWAP

HSWAP must be stable before INIT_B goes High and constant throughout the configuration process.

(Input)

VS[2:0]

<1:1:1>

(Input)

M[2:0]

Mode input pins M[2:0] and variant select input pins VS[2:0] are sampled when INIT_B goes High. After this point, input values do not matter until DONE goes High, at which point these pins become user-I/O pins.

<0:0:1>

(Input)

TMINIT

TINITM

INIT_B New ConfigRate active

(Open-Drain)

TCCLKn TMCCHn

TMCCLn TCCLK1

TMCCL1 TMCCH1

T CCLK1 CCLK

TV DIN

Data

(Input)

Data

TCSS

Data

Data

TDCC TCCD

CSO_B TCCO Command (msb)

MOSI

Command (msb-1)

TDSU

T DH

Pin initially pulled High by internal pull-up resistor if HSWAP input is Low. Pin initially high-impedance (Hi-Z) if HSWAP input is High. External pull-up resistor required on CSO_B.

Shaded values indicate specifications on attached SPI Flash PROM.

ds312-3_06_110206

Figure 76: Waveforms for Serial Peripheral Interface (SPI) Configuration Table 118: Timing for Serial Peripheral Interface (SPI) Configuration Mode Symbol

Description

Minimum

Maximum

Units

TCCLK1

Initial CCLK clock period

See Table 112

TCCLKn

CCLK clock period after FPGA loads ConfigRate setting

See Table 112

TMINIT

Setup time on VS[2:0] and M[2:0] mode pins before the rising edge of INIT_B

50

-

ns

TINITM

Hold time on VS[2:0] and M[2:0]mode pins after the rising edge of INIT_B

0

-

ns

TCCO

MOSI output valid after CCLK edge

See Table 116

TDCC

Setup time on DIN data input before CCLK edge

See Table 116

TCCD

Hold time on DIN data input after CCLK edge

See Table 116

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 150

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 119: Configuration Timing Requirements for Attached SPI Serial Flash Symbol

Description

Requirement

Units

TCCS

SPI serial Flash PROM chip-select time

T CCS ≤ T MCCL1 – T CCO

ns

TDSU

SPI serial Flash PROM data input setup time

T DSU ≤ T MCCL1 – T CCO

ns

TDH

SPI serial Flash PROM data input hold time

T DH ≤ T MCCH 1

ns

TV

SPI serial Flash PROM data clock-to-output time

T V ≤ T MCCLn – T DCC

ns

fC or fR

Maximum SPI serial Flash PROM clock frequency (also depends on specific read command used)

1 f C ≥ ------------------------------T CCLKn ( min )

MHz

Notes: 1. 2.

These requirements are for successful FPGA configuration in SPI mode, where the FPGA provides the CCLK frequency. The post configuration timing can be different to support the specific needs of the application loaded into the FPGA and the resulting clock source. Subtract additional printed circuit board routing delay as required by the application.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 151

Spartan-3E FPGA Family: DC and Switching Characteristics

Byte Peripheral Interface (BPI) Configuration Timing X-Ref Target - Figure 77

PROG_B (Input) HSWAP (Input)

HSWAP must be stable before INIT_B goes High and constant throughout the configuration process.

M[2:0] (Input)

Mode input pins M[2:0] are sampled when INIT_B goes High. After this point, input values do not matter until DONE goes High, at which point the mode pins become user-I/O pins.

<0:1:0> TMINIT

INIT_B (Open-Drain)

TINITM

Pin initially pulled High by internal pull-up resistor if HSWAP input is Low. Pin initially high-impedance (Hi-Z) if HSWAP input is High.

LDC[2:0]

HDC

CSO_B

New ConfigRate active

TCCLK1

TCCLK1

T INITADDR

TCCLKn

CCLK TCCO 000_0000

A[23:0]

Address

000_0001 TAVQV

D[7:0] (Input)

Byte 0

Byte 1

Address

Address TCCD

TDCC

Data

Data

Data

Data

Shaded values indicate specifications on attached parallel NOR Flash PROM. DS312-3_08_032409

Figure 77: Waveforms for Byte-wide Peripheral Interface (BPI) Configuration (BPI-DN mode shown) Table 120: Timing for Byte-wide Peripheral Interface (BPI) Configuration Mode Symbol

Description

Minimum

Maximum

Units

TCCLK1

Initial CCLK clock period

See Table 112

TCCLKn

CCLK clock period after FPGA loads ConfigRate setting

See Table 112

TMINIT

Setup time on CSI_B, RDWR_B, and M[2:0] mode pins before the rising edge of INIT_B

50

-

ns

TINITM

Hold time on CSI_B, RDWR_B, and M[2:0] mode pins after the rising edge of INIT_B

0

-

ns

TINITADDR

Minimum period of initial A[23:0] address cycle; LDC[2:0] and HDC are asserted and valid

BPI-UP: (M[2:0] = <0:1:0>)

5

5

TCCLK1 cycles

BPI-DN: (M[2:0] = <0:1:1>)

2

2

TCCO

Address A[23:0] outputs valid after CCLK falling edge

See Table 116

TDCC

Setup time on D[7:0] data inputs before CCLK rising edge

See Table 116

TCCD

Hold time on D[7:0] data inputs after CCLK rising edge

See Table 116

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 152

Spartan-3E FPGA Family: DC and Switching Characteristics

Table 121: Configuration Timing Requirements for Attached Parallel NOR Flash Symbol

Description

Requirement

Units

TCE (tELQV)

Parallel NOR Flash PROM chip-select time

T CE ≤ T INITADDR

ns

TOE (tGLQV)

Parallel NOR Flash PROM output-enable time

T OE ≤ T INITADDR

ns

TACC (tAVQV)

Parallel NOR Flash PROM read access time

T ACC ≤ 0.5T CCLKn ( min ) – T CCO – T DCC – PCB

ns

T BYTE ≤ T INITADDR

ns

TBYTE (tFLQV, tFHQV) For x8/x16 PROMs only: BYTE# to output valid time(3) Notes: 1. 2. 3.

These requirements are for successful FPGA configuration in BPI mode, where the FPGA provides the CCLK frequency. The post configuration timing can be different to support the specific needs of the application loaded int o the FPGA and the resulting clock source. Subtract additional printed circuit board routing delay as required by the application. The initial BYTE# timing can be extended using an external, appropriately sized pull-down resistor on the FPGA’s LDC2 pin. The resistor value also depends on whether the FPGA’s HSWAP pin is High or Low.

Table 122: MultiBoot Trigger (MBT) Timing Symbol TMBT

Description MultiBoot Trigger (MBT) Low pulse width required to initiate MultiBoot reconfiguration

Minimum

Maximum

Units

300



ns

Notes: 1.

MultiBoot re-configuration starts on the rising edge after MBT is Low for at least the prescribed minimum period.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 153

Spartan-3E FPGA Family: DC and Switching Characteristics

IEEE 1149.1/1532 JTAG Test Access Port Timing X-Ref Target - Figure 78

TCCH

TCCL

TCK (Input) TTMSTCK

1/FTCK

TTCKTMS

TMS (Input) TTDITCK

TTCKTDI

TDI (Input) TTCKTDO

TDO (Output) DS312-3_79_032409

Figure 78: JTAG Waveforms Table 123: Timing for the JTAG Test Access Port Symbol

All Speed Grades

Description

Units

Min

Max

The time from the falling transition on the TCK pin to data appearing at the TDO pin

1.0

11.0

ns

TTDITCK

The time from the setup of data at the TDI pin to the rising transition at the TCK pin

7.0

-

ns

TTMSTCK

The time from the setup of a logic level at the TMS pin to the rising transition at the TCK pin

7.0

-

ns

TTCKTDI

The time from the rising transition at the TCK pin to the point when data is last held at the TDI pin

0

-

ns

TTCKTMS

The time from the rising transition at the TCK pin to the point when a logic level is last held at the TMS pin

0

-

ns

TCCH

The High pulse width at the TCK pin

5

-

ns

TCCL

The Low pulse width at the TCK pin

5

-

ns

FTCK

Frequency of the TCK signal

-

30

MHz

Clock-to-Output Times TTCKTDO

Setup Times

Hold Times

Clock Timing

Notes: 1.

The numbers in this table are based on the operating conditions set forth in Table 77.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 154

Spartan-3E FPGA Family: DC and Switching Characteristics

Revision History The following table shows the revision history for this document. Date

Version

03/01/2005

1.0

Initial Xilinx release.

11/23/2005

2.0

Added AC timing information and additional DC specifications.

03/22/2006

3.0

Upgraded data sheet status to Preliminary. Finalized production timing parameters. All speed grades for all Spartan-3E FPGAs are now Production status using the v1.21 speed files, as shown in Table 84. Expanded description in Note 2, Table 78. Updated pin-to-pin and clock-to-output timing based on final characterization, shown in Table 86. Updated system-synchronous input setup and hold times based on final characterization, shown in Table 87 and Table 88. Updated other I/O timing in Table 90. Provided input and output adjustments for LVPECL_25, DIFF_SSTL and DIFF_HSTL I/O standards that supersede the v1.21 speed file values, in Table 91 and Table 94. Reduced I/O three-state and set/reset delays in Table 93. Added XC3S100E FPGA in CP132 package to Table 96. Increased TAS slice flip-flop timing by 100 ps in Table 98. Updated distributed RAM timing in Table 99 and SRL16 timing in Table 100. Updated global clock timing, removed left/right clock buffer limits in Table 101. Updated block RAM timing in Table 103. Added DCM parameters for remainder of Step 0 device; added improved Step 1 DCM performance to Table 104, Table 105, Table 106, and Table 107. Added minimum INIT_B pulse width specification, TINIT, in Table 111. Increased data hold time for Slave Parallel mode to 1.0 ns (TSMCCD) in Table 117. Improved the DCM performance for the XC3S1200E, Stepping 0 in Table 104, Table 105, Table 106, and Table 107. Corrected links in Table 118 and Table 120. Added MultiBoot timing specifications to Table 122.

04/07/2006

3.1

Improved SSO limits for LVDS_25, MINI_LVDS_25, and RSDS_25 I/O standards in the QFP packages (Table 97). Removed potentially confusing Note 2 from Table 78.

05/19/2006

3.2

Clarified that 100 mV of hysteresis applies to LVCMOS33 and LVCMOS25 I/O standards (Note 4, Table 80). Other minor edits.

05/30/2006

3.2.1

11/09/2006

3.4

Improved absolute maximum voltage specifications in Table 73, providing additional overshoot allowance. Widened the recommended voltage range for PCI and PCI-X standards in Table 80. Clarified Note 2, Table 83. Improved various timing specifications for v1.26 speed file. Added Table 85 to summarize the history of speed file releases after which time all devices became Production status. Added absolute minimum values for Table 86, Table 92, and Table 93. Updated pin-to-pin setup and hold timing based on default IFD_DELAY_VALUE settings in Table 87, Table 88, and Table 90. Added Table 89 about source-synchronous input capture sample window. Promoted Module 3 to Production status. Synchronized all modules to v3.4.

03/16/2007

3.5

Based on extensive 90 nm production data, improved (reduced) the maximum quiescent current limits for the ICCINTQ, ICCAUXQ, and ICCOQ specifications in Table 79 by an average of 50%.

05/29/2007

3.6

Added note to Table 74 and Table 75 regarding HSWAP in step 0 devices. Updated tRPW_CLB in Table 98 to match value in speed file. Improved CLKOUT_FREQ_CLK90 to 200 MHz for Stepping 1 in Table 105.

04/18/2008

3.7

Clarified that Stepping 0 was offered only for -4C and removed Stepping 0 -5 specifications. Added reference to XAPP459 in Table 73 and Table 77. Improved recommended max VCCO to 3.465V (3.3V + 5%) in Table 77. Removed minimum input capacitance from Table 78. Updated Recommended Operating Conditions for LVCMOS and PCI I/O standards in Table 80. Removed Absolute Minimums from Table 86, Table 92 and Table 93 and added footnote recommending use of Timing Analyzer for minimum values. Updated TPSFD and TPHFD in Table 87 to match current speed file. Update TRPW_IOB in Table 88 to match current speed file and CLB equivalent spec. Added XC3S500E VQG100 to Table 96. Replaced TMULCKID with TMSCKD for A, B, and P registers in Table 102. Updated CLKOUT_PER_JITT_FX in Table 107. Updated MAX_STEPS equation in Table 109. Updated Figure 77 and Table 120 to correct CCLK active edge. Updated links.

08/26/2009

3.8

Added reference to XAPP459 in Table 73 note 2. Updated BPI timing in Figure 77, Table 119, and Table 120. Removed VREF requirements for differential HSTL and differential SSTL in Table 95. Added Spread Spectrum paragraph. Revised hold times for TIOICKPD in Table 88 and setup times for TDICK in Table 98. Added note 4 to Table 106 and note 3 to Table 107, and updated note 6 for Table 107 to add input jitter.

DS312 (v4.1) July 19, 2013 Product Specification

Revision

Corrected various typos and incorrect links.

www.xilinx.com 155

Spartan-3E FPGA Family: DC and Switching Characteristics

Date

Version

Revision

10/29/2012

4.0

Added Notice of Disclaimer. This product is not recommended for new designs. Revised note 2 in Table 73. Revised note 2 and VIN description in Table 77, and added note 5. Added note 3 to Table 78.

07/19/2013

4.1

Removed banner. This product IS recommended for new designs.

Notice of Disclaimer THE XILINX HARDWARE FPGA AND CPLD DEVICES REFERRED TO HEREIN (“PRODUCTS”) ARE SUBJECT TO THE TERMS AND CONDITIONS OF THE XILINX LIMITED WARRANTY WHICH CAN BE VIEWED AT http://www.xilinx.com/warranty.htm. THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY USE OF PRODUCTS IN AN APPLICATION OR ENVIRONMENT THAT IS NOT WITHIN THE SPECIFICATIONS STATED IN THE XILINX DATA SHEET. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, OR ANY OTHER APPLICATION THAT INVOKES THE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). USE OF PRODUCTS IN CRITICAL APPLICATIONS IS AT THE SOLE RISK OF CUSTOMER, SUBJECT TO APPLICABLE LAWS AND REGULATIONS. CRITICAL APPLICATIONS DISCLAIMER XILINX PRODUCTS (INCLUDING HARDWARE, SOFTWARE AND/OR IP CORES) ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS IN LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, CLASS III MEDICAL DEVICES, NUCLEAR FACILITIES, APPLICATIONS RELATED TO THE DEPLOYMENT OF AIRBAGS, OR ANY OTHER APPLICATIONS THAT COULD LEAD TO DEATH, PERSONAL INJURY OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (INDIVIDUALLY AND COLLECTIVELY, “CRITICAL APPLICATIONS”). FURTHERMORE, XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN ANY APPLICATIONS THAT AFFECT CONTROL OF A VEHICLE OR AIRCRAFT, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE OPERATOR. CUSTOMER AGREES, PRIOR TO USING OR DISTRIBUTING ANY SYSTEMS THAT INCORPORATE XILINX PRODUCTS, TO THOROUGHLY TEST THE SAME FOR SAFETY PURPOSES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN CRITICAL APPLICATIONS. AUTOMOTIVE APPLICATIONS DISCLAIMER XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS APPLICATIONS RELATED TO: (I) THE DEPLOYMENT OF AIRBAGS, (II) CONTROL OF A VEHICLE, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE OPERATOR, OR (III) USES THAT COULD LEAD TO DEATH OR PERSONAL INJURY. CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN SUCH APPLICATIONS.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 156

227

Spartan-3E FPGA Family: Pinout Descriptions

DS312 (v4.1) July 19, 2013

Product Specification

Introduction

Pin Types

This section describes the various pins on a Spartan®-3E FPGA and how they connect within the supported component packages.

Most pins on a Spartan-3E FPGA are general-purpose, user-defined I/O pins. There are, however, up to 11 different functional types of pins on Spartan-3E packages, as outlined in Table 124. In the package footprint drawings that follow, the individual pins are color-coded according to pin type as in the table.

Table 124: Types of Pins on Spartan-3E FPGAs Type / Color Code I/O

Pin Name(s) in Type(1)

Description

Unrestricted, general-purpose user-I/O pin. Most pins can be paired together to form IO differential I/Os. IO_Lxxy_#

INPUT

Unrestricted, general-purpose input-only pin. This pin does not have an output structure, differential termination resistor, or PCI clamp diode.

IP IP_Lxxy_#

DUAL

Dual-purpose pin used in some configuration modes during the configuration process and then usually available as a user I/O after configuration. If the pin is not used during configuration, this pin behaves as an I/O-type pin. Some of the dual-purpose pins are also shared with bottom-edge global (GCLK) or right-half (RHCLK) clock inputs. See the Configuration section in Module 2 for additional information on these signals.

M[2:0] HSWAP CCLK MOSI/CSI_B D[7:1] D0/DIN CSO_B RDWR_B BUSY/DOUT INIT_B A[23:20] A19/VS2 A18/VS1 A17/VS0 A[16:0] LDC[2:0] HDC

VREF

Dual-purpose pin that is either a user-I/O pin or Input-only pin, or, along with all other VREF pins in the same bank, provides a reference voltage input for certain I/O standards. If used for a reference voltage within a bank, all VREF pins within the bank must be connected.

IP/VREF_# IP_Lxxy_#/VREF_# IO/VREF_# IO_Lxxy_#/VREF_#

CLK

Either a user-I/O pin or Input-only pin, or an input to a specific clock buffer driver. Every package has 16 global clock inputs that optionally clock the entire device. The RHCLK inputs optionally clock the right-half of the device. The LHCLK inputs optionally clock the left-half of the device. Some of the clock pins are shared with the dual-purpose configuration pins and are considered DUAL-type. See the Clocking Infrastructure section in Module 2 for additional information on these signals.

IO_Lxxy_#/GCLK[15:10, 7:2] IP_Lxxy_#/GCLK[9:8, 1:0] IO_Lxxy_#/LHCLK[7:0] IO_Lxxy_#/RHCLK[7:0]

CONFIG

Dedicated configuration pin. Not available as a user-I/O pin. Every package has two dedicated configuration pins. These pins are powered by VCCAUX. See the Configuration section in Module 2 for details.

DONE, PROG_B

JTAG

Dedicated JTAG pin. Not available as a user-I/O pin. Every package has four dedicated JTAG pins. These pins are powered by VCCAUX.

TDI, TMS, TCK, TDO

GND

Dedicated ground pin. The number of GND pins depends on the package used. All must be connected.

GND

© Copyright 2005–2013 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Spartan, ISE, Artix, Kintex, Zynq, Vivado, and other designated brands included herein are trademarks of Xilinx in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 157

Spartan-3E FPGA Family: Pinout Descriptions Table 124: Types of Pins on Spartan-3E FPGAs (Cont’d) Type / Color Code

Pin Name(s) in Type(1)

Description

VCCAUX

Dedicated auxiliary power supply pin. The number of VCCAUX pins depends on the package used. All must be connected to +2.5V. See the Powering Spartan-3E FPGAs section in Module 2 for details.

VCCAUX

VCCINT

Dedicated internal core logic power supply pin. The number of VCCINT pins depends on the package used. All must be connected to +1.2V. See the Powering Spartan-3E FPGAs section in Module 2 for details.

VCCINT

VCCO

Along with all the other VCCO pins in the same bank, this pin supplies power to the output buffers within the I/O bank and sets the input threshold voltage for some I/O standards. See the Powering Spartan-3E FPGAs section in Module 2 for details.

VCCO_#

N.C.

This package pin is not connected in this specific device/package combination but may be connected in larger devices in the same package.

N.C.

Notes: 1. 2.

# = I/O bank number, an integer between 0 and 3. IRDY/TRDY designations are for PCI designs; refer to PCI documentation for details.

Differential Pair Labeling

‘L’ indicates that the pin is part of a differential pair.

I/Os with Lxxy_# are part of a differential pair. ‘L’ indicates differential capability. The ‘xx’ field is a two-digit integer, unique to each bank that identifies a differential pin-pair. The ‘y’ field is either ‘P’ for the true signal or ‘N’ for the inverted signal in the differential pair. The ‘#’ field is the I/O bank number.

‘xx’ is a two-digit integer, unique for each bank, that identifies a differential pin-pair. ‘y’ is replaced by ‘P’ for the true signal or ‘N’ for the inverted. These two pins form one differential pin-pair. ‘#’ is an integer, 0 through 3, indicating the associated I/O bank.

The pin name suffix has the following significance. Figure 79 provides a specific example showing a differential input to and a differential output from Bank 1. X-Ref Target - Figure 79

Pair Number Bank Number

Bank 0

Spartan-3E FPGA

IO_L38N_1

Bank 1

Bank 3

IO_L38P_1 Positive Polarity True Receiver

IO_L39P_1 IO_L39N_1

Negative Polarity Inverted Receiver

Bank 2 DS312-4_00_032409

Figure 79: Differential Pair Labeling

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 158

Spartan-3E FPGA Family: Pinout Descriptions

Package Overview

packages are similar, as shown in the mechanical drawings provided in Table 127.

Table 125 shows the eight low-cost, space-saving production package styles for the Spartan-3E family. Each package style is available as a standard and an environmentally friendly lead-free (Pb-free) option. The Pb-free packages include an extra ‘G’ in the package style name. For example, the standard “VQ100” package becomes “VQG100” when ordered as the Pb-free option. The mechanical dimensions of the standard and Pb-free

Not all Spartan-3E densities are available in all packages. For a specific package, however, there is a common footprint that supports all the devices available in that package. See the footprint diagrams that follow. For additional package information, see UG112: Device Package User Guide.

Table 125: Spartan-3E Family Package Options Maximum I/O

Lead Pitch (mm)

Footprint Area (mm)

Height (mm)

Very-thin Quad Flat Pack (VQFP)

66

0.5

16 x 16

1.20

0.6

132

Chip-Scale Package (CSP)

92

0.5

8.1 x 8.1

1.10

0.1

TQ144 / TQG144

144

Thin Quad Flat Pack (TQFP)

108

0.5

22 x 22

1.60

1.4

PQ208 / PQG208

208

Plastic Quad Flat Pack (PQFP)

158

0.5

30.6 x 30.6

4.10

5.3

FT256 / FTG256

256

Fine-pitch, Thin Ball Grid Array (FBGA)

190

1.0

17 x 17

1.55

0.9

FG320 / FGG320

320

Fine-pitch Ball Grid Array (FBGA)

250

1.0

19 x 19

2.00

1.4

FG400 / FGG400

400

Fine-pitch Ball Grid Array (FBGA)

304

1.0

21 x 21

2.43

2.2

FG484 / FGG484

484

Fine-pitch Ball Grid Array (FBGA)

376

1.0

23 x 23

2.60

2.2

Package

Leads

VQ100 / VQG100

100

CP132 / CPG132

Type

Mass(1) (g)

Notes: 1.

Package mass is ±10%.

Selecting the Right Package Option Spartan-3E FPGAs are available in both quad-flat pack (QFP) and ball grid array (BGA) packaging options. While QFP packaging offers the lowest absolute cost, the BGA

packages are superior in almost every other aspect, as summarized in Table 126. Consequently, Xilinx recommends using BGA packaging whenever possible.

Table 126: QFP and BGA Comparison Characteristic

Quad Flat Pack (QFP)

Ball Grid Array (BGA)

158

376

Good

Better

Signal Integrity

Fair

Better

Simultaneous Switching Output (SSO) Support

Fair

Better

Thermal Dissipation

Fair

Better

4

4-6

Possible

Difficult

Maximum User I/O Packing Density (Logic/Area)

Minimum Printed Circuit Board (PCB) Layers Hand Assembly/Rework

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 159

Spartan-3E FPGA Family: Pinout Descriptions

Mechanical Drawings

Material Declaration Data Sheets (MDDS) are also available on the Xilinx web site for each package.

Detailed mechanical drawings for each package type are available from the Xilinx® web site at the specified location in Table 127. Table 127: Xilinx Package Mechanical Drawings and Material Declaration Data Sheets Package

Package Drawing

VQ100

Package Drawing

MDDS PK173_VQ100

VQG100

PK130_VQG100

CP132

Package Drawing

PK147_CP132

CPG132

PK101_CPG132

TQ144

Package Drawing

PK169_TQ144

TQG144

PK126_TQG144

PQ208

Package Drawing

PK166_PQ208

PQG208

PK123_PQG208

FT256

Package Drawing

PK158_FT256

FTG256

PK115_FTG256

FG320

Package Drawing

PK152_FG320

FGG320

PK106_FGG320

FG400

Package Drawing

PK182_FG400

FGG400

PK108_FGG400

FG484

Package Drawing

PK183_FG484

FGG484

PK110_FGG484

Package Pins by Type Each package has three separate voltage supply inputs—VCCINT, VCCAUX, and VCCO—and a common ground return, GND. The numbers of pins dedicated to these functions vary by package, as shown in Table 128.

CLK-type pins are used as general-purpose I/O. Likewise, the table shows the maximum number of differential pin-pairs available on the package. Finally, the table shows how the total maximum user-I/Os are distributed by pin type, including the number of unconnected—i.e., N.C.—pins on the device.

Table 128: Power and Ground Supply Pins by Package Package

VCCINT

VCCAUX

VCCO

GND

VQ100

4

4

8

12

CP132

6

4

8

16

TQ144

4

4

9

13

PQ208

4

8

12

20

FT256

8

8

16

28

FG320

8

8

20

28

FG400

16

8

24

42

FG484

16

10

28

48

A majority of package pins are user-defined I/O or input pins. However, the numbers and characteristics of these I/O depend on the device type and the package in which it is available, as shown in Table 129. The table shows the maximum number of single-ended I/O pins available, assuming that all I/O-, INPUT-, DUAL-, VREF-, and DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 160

Spartan-3E FPGA Family: Pinout Descriptions

Table 129: Maximum User I/O by Package Maximum User I/Os and Input-Only

Maximum InputOnly

Maximum Differential Pairs

I/O

INPUT

DUAL

VREF(1)

CLK(2)

N.C.

66

7

30

16

1

21

4

24

0

66

7

30

16

1

21

4

24

0

XC3S500E

66

7

30

16

1

21

4

24

0

XC3S100E

83

11

35

16

2

42

7

16

9

92

7

41

22

0

46

8

16

0

92

7

41

22

0

46

8

16

0

108

28

40

22

19

42

9

16

0

108

28

40

20

21

42

9

16

0

158

32

65

58

25

46

13

16

0

158

32

65

58

25

46

13

16

0

172

40

68

62

33

46

15

16

18

190

41

77

76

33

46

19

16

0

XC3S1200E

190

40

77

78

31

46

19

16

0

XC3S500E

232

56

92

102

48

46

20

16

18

250

56

99

120

47

46

21

16

0

250

56

99

120

47

46

21

16

0

304

72

124

156

62

46

24

16

0

304

72

124

156

62

46

24

16

0

376

82

156

214

72

46

28

16

0

Device

Package

XC3S100E XC3S250E

XC3S250E

VQ100

CP132

XC3S500E XC3S100E XC3S250E XC3S250E XC3S500E

TQ144

PQ208

XC3S250E XC3S500E

XC3S1200E

FT256

FG320

XC3S1600E XC3S1200E XC3S1600E XC3S1600E

FG400 FG484

All Possible I/Os by Type

Notes: 1. 2.

Some VREF pins are on INPUT pins. See pinout tables for details. All devices have 24 possible global clock and right- and left-half side clock inputs. The right-half and bottom-edge clock pins have shared functionality in some FPGA configuration modes. Consequently, some clock pins are counted in the DUAL column. 4 GCLK pins, including 2 DUAL pins, are on INPUT pins.

Electronic versions of the package pinout tables and footprints are available for download from the Xilinx website. Download the files from the following location: http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip Using a spreadsheet program, the data can be sorted and reformatted according to any specific needs. Similarly, the ASCII-text file is easily parsed by most scripting programs.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 161

Spartan-3E FPGA Family: Pinout Descriptions

Package Thermal Characteristics The power dissipated by an FPGA application has implications on package selection and system design. The power consumed by a Spartan-3E FPGA is reported using either the XPower Estimator or the XPower Analyzer calculator integrated in the Xilinx ISE® development software. Table 130 provides the thermal characteristics for the various Spartan-3E package offerings. The junction-to-case thermal resistance (θJC) indicates the difference between the temperature measured on the

package body (case) and the die junction temperature per watt of power consumption. The junction-to-board (θJB) value similarly reports the difference between the board and junction temperature. The junction-to-ambient (θJA) value reports the temperature difference per watt between the ambient environment and the junction temperature. The θJA value is reported at different air velocities, measured in linear feet per minute (LFM). The Still Air (0 LFM) column shows the θJA value in a system without a fan. The thermal resistance drops with increasing air flow.

Table 130: Spartan-3E Package Thermal Characteristics

Device

Package

XC3S100E XC3S250E

VQ100

Junction-to-Case (θJC)

Junction-to-Board (θJB)

13.0 11.0

Junction-to-Ambient (θJA) at Different Air Flows

Units

Still Air (0 LFM)

250 LFM

500 LFM

750 LFM

30.9

49.0

40.7

37.9

37.0

°C/Watt

25.9

43.3

36.0

33.6

32.7

°C/Watt

40.0

33.3

31.0

30.2

°C/Watt

XC3S500E

9.8

XC3S100E

19.3

42.0

62.1

55.3

52.8

51.2

°C/Watt

11.8

28.1

48.3

41.8

39.5

38.0

°C/Watt

8.5

21.3

41.5

35.2

32.9

31.5

°C/Watt

8.2

31.9

52.1

40.5

34.6

32.5

°C/Watt

7.2

25.7

37.6

29.2

25.0

23.4

°C/Watt

9.8

29.0

37.0

27.3

24.1

22.4

°C/Watt

8.5

26.8

36.1

26.6

23.6

21.8

°C/Watt

12.4

27.7

35.8

29.3

28.4

28.1

°C/Watt

9.6

22.2

31.1

25.0

24.0

23.6

°C/Watt

XC3S1200E

6.5

16.4

26.2

20.5

19.3

18.9

°C/Watt

XC3S500E

9.8

15.6

26.1

20.6

19.4

18.6

°C/Watt

8.2

12.5

23.0

17.7

16.4

15.7

°C/Watt

7.1

10.6

21.1

15.9

14.6

13.8

°C/Watt

7.5

12.4

22.3

17.2

16.0

15.3

°C/Watt

6.0

10.4

20.3

15.2

14.0

13.3

°C/Watt

5.7

9.4

18.8

12.5

11.3

10.8

°C/Watt

XC3S250E

CP132

XC3S500E XC3S100E XC3S250E XC3S250E XC3S500E

TQ144

PQ208

XC3S250E XC3S500E

XC3S1200E

FT256

FG320

XC3S1600E XC3S1200E XC3S1600E XC3S1600E

FG400 FG484

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 162

Spartan-3E FPGA Family: Pinout Descriptions

VQ100: 100-lead Very-thin Quad Flat Package The XC3S100E, XC3S250E, and the XC3S500E devices are available in the 100-lead very-thin quad flat package, VQ100. All devices share a common footprint for this package as shown in Table 131 and Figure 80. Table 131 lists all the package pins. They are sorted by bank number and then by pin name. Pins that form a differential I/O pair appear together in the table. The table also shows the pin number for each pin and the pin type, as defined earlier.

Table 131: VQ100 Package Pinout (Cont’d) XC3S100E XC3S250E XC3S500E Pin Name

Bank

VQ100 Pin Number

Type

1

IO_L02P_1

P57

I/O

1

IO_L03N_1/RHCLK1

P61

RHCLK

1

IO_L03P_1/RHCLK0

P60

RHCLK

1

IO_L04N_1/RHCLK3

P63

RHCLK

The VQ100 package does not support the Byte-wide Peripheral Interface (BPI) configuration mode. Consequently, the VQ100 footprint has fewer DUAL-type pins than other packages.

1

IO_L04P_1/RHCLK2

P62

RHCLK

1

IO_L05N_1/RHCLK5

P66

RHCLK

1

IO_L05P_1/RHCLK4

P65

RHCLK

1

IO_L06N_1/RHCLK7

P68

RHCLK

An electronic version of this package pinout table and footprint diagram is available for download from the Xilinx web site at:

1

IO_L06P_1/RHCLK6

P67

RHCLK

1

IO_L07N_1

P71

I/O I/O

1

IO_L07P_1

P70

http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip

1

IP/VREF_1

P69

VREF

1

VCCO_1

P55

VCCO

Pinout Table

1

VCCO_1

P73

VCCO

2

IO/D5

P34

DUAL

Table 131 shows the pinout for production Spartan-3E FPGAs in the VQ100 package.

2

IO/M1

P42

DUAL

2

IO_L01N_2/INIT_B

P25

DUAL

Table 131: VQ100 Package Pinout

2

IO_L01P_2/CSO_B

P24

DUAL

2

IO_L02N_2/MOSI/CSI_B

P27

DUAL

2

IO_L02P_2/DOUT/BUSY

P26

DUAL

2

IO_L03N_2/D6/GCLK13

P33

DUAL/GCLK

XC3S100E XC3S250E XC3S500E Pin Name

Bank

VQ100 Pin Number

Type

0

IO

P92

I/O

2

IO_L03P_2/D7/GCLK12

P32

DUAL/GCLK

0

IO_L01N_0

P79

I/O

2

IO_L04N_2/D3/GCLK15

P36

DUAL/GCLK

0

IO_L01P_0

P78

I/O

2

IO_L04P_2/D4/GCLK14

P35

DUAL/GCLK

0

IO_L02N_0/GCLK5

P84

GCLK

2

IO_L06N_2/D1/GCLK3

P41

DUAL/GCLK

IO_L06P_2/D2/GCLK2

P40

DUAL/GCLK

0

IO_L02P_0/GCLK4

P83

GCLK

2

0

IO_L03N_0/GCLK7

P86

GCLK

2

IO_L07N_2/DIN/D0

P44

DUAL

0

IO_L03P_0/GCLK6

P85

GCLK

2

IO_L07P_2/M0

P43

DUAL

IO_L08N_2/VS1

P48

DUAL

0

IO_L05N_0/GCLK11

P91

GCLK

2

0

IO_L05P_0/GCLK10

P90

GCLK

2

IO_L08P_2/VS2

P47

DUAL

0

IO_L06N_0/VREF_0

P95

VREF

2

IO_L09N_2/CCLK

P50

DUAL

0

IO_L06P_0

P94

I/O

2

IO_L09P_2/VS0

P49

DUAL

0

IO_L07N_0/HSWAP

P99

DUAL

2

IP/VREF_2

P30

VREF

IP_L05N_2/M2/GCLK1

P39

DUAL/GCLK

0

IO_L07P_0

P98

I/O

2

0

IP_L04N_0/GCLK9

P89

GCLK

2

P38

DUAL/GCLK

0

IP_L04P_0/GCLK8

P88

GCLK

IP_L05P_2/RDWR_B/ GCLK0

0

VCCO_0

P82

VCCO

2

VCCO_2

P31

VCCO

0

VCCO_0

P97

VCCO

2

VCCO_2

P45

VCCO

3

IO_L01N_3

P3

I/O

3

IO_L01P_3

P2

I/O

3

IO_L02N_3/VREF_3

P5

VREF

1

IO_L01N_1

P54

I/O

1

IO_L01P_1

P53

I/O

1

IO_L02N_1

P58

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 163

Spartan-3E FPGA Family: Pinout Descriptions Table 131: VQ100 Package Pinout (Cont’d) XC3S100E XC3S250E XC3S500E Pin Name

Bank

VQ100 Pin Number

Type

3

IO_L02P_3

P4

I/O

3

IO_L03N_3/LHCLK1

P10

LHCLK

3

IO_L03P_3/LHCLK0

P9

LHCLK

3

IO_L04N_3/LHCLK3

P12

LHCLK

3

IO_L04P_3/LHCLK2

P11

LHCLK

3

IO_L05N_3/LHCLK5

P16

LHCLK

3

IO_L05P_3/LHCLK4

P15

LHCLK

3

IO_L06N_3/LHCLK7

P18

LHCLK

3

IO_L06P_3/LHCLK6

P17

LHCLK

3

IO_L07N_3

P23

I/O

3

IO_L07P_3

P22

I/O

3

IP

P13

INPUT

3

VCCO_3

P8

VCCO

3

VCCO_3

P20

VCCO

GND

GND

P7

GND

GND

GND

P14

GND

GND

GND

P19

GND

GND

GND

P29

GND

GND

GND

P37

GND

GND

GND

P52

GND

GND

GND

P59

GND

GND

GND

P64

GND

GND

GND

P72

GND

GND

GND

P81

GND

GND

GND

P87

GND

GND

GND

P93

GND

VCCAUX DONE

P51

CONFIG

VCCAUX PROG_B

P1

CONFIG

VCCAUX TCK

P77

JTAG

VCCAUX TDI

P100

JTAG

VCCAUX TDO

P76

JTAG

VCCAUX TMS

P75

JTAG

VCCAUX VCCAUX

P21

VCCAUX

VCCAUX VCCAUX

P46

VCCAUX

VCCAUX VCCAUX

P74

VCCAUX

VCCAUX VCCAUX

P96

VCCAUX

VCCINT VCCINT

P6

VCCINT

VCCINT VCCINT

P28

VCCINT

VCCINT VCCINT

P56

VCCINT

VCCINT VCCINT

P80

VCCINT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 164

Spartan-3E FPGA Family: Pinout Descriptions

User I/Os by Bank Table 132 indicates how the 66 available user-I/O pins are distributed between the four I/O banks on the VQ100 package. Table 132: User I/Os Per Bank for XC3S100E, XC3S250E, and XC3S500E in the VQ100 Package Package Edge

All Possible I/O Pins by Type

I/O Bank

Maximum I/O

I/O

INPUT

DUAL

Top

0

15

5

0

1

1

8

Right

1

15

6

0

0

1

8

Bottom

2

19

0

0

18

1

0(2)

Left

3

17

5

1

2

1

8

66

16

1

21

4

24

TOTAL

VREF(1)

CLK(2)

Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

Footprint Migration Differences The production XC3S100E, XC3S250E, and XC3S500E FPGAs have identical footprints in the VQ100 package. Designs can migrate between the devices without further consideration.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 165

Spartan-3E FPGA Family: Pinout Descriptions

VQ100 Footprint In Figure 80, note pin 1 indicator in top-left corner and logo orientation.

100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76

TDI IO_L07N_0/HSWAP IO_L07P_0 VCCO_0 VCCAUX IO_L06N_0/VREF_0 IO_L06P_0 GND IO IO_L05N_0/GCLK11 IO_L05P_0/GCLK10 IP_L04N_0/GCLK9 IP_L04P_0/GCLK8 GND IO_L03N_0/GCLK7 IO_L03P_0/GCLK6 IO_L02N_0/GCLK5 IO_L02P_0/GCLK4 VCCO_0 GND VCCINT IO_L01N_0 IO_L01P_0 TCK TDO

X-Ref Target - Figure 80

3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

IO_L01P_2/CSO_B IO_L01N_2/INIT_B

24 25

Bank 1

IO_L01N_3 IO_L02P_3 IO_L02N_3/VREF_3 VCCINT GND VCCO_3 IO_L03P_3/LHCLK0 IO_L03N_3/LHCLK1 IO_L04P_3/LHCLK2 IO_L04N_3/LHCLK3 IP GND IO_L05P_3/LHCLK4 IO_L05N_3/LHCLK5 IO_L06P_3/LHCLK6 IO_L06N_3/LHCLK7 GND VCCO_3 VCCAUX IO_L07P_3 IO_L07N_3

Bank 0

Bank 3

1 2

Bank 2

75 74

TMS VCCAUX

73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53

VCCO_1 GND IO_L07N_1 IO_L07P_1 IP/VREF_1 IO_L06N_1/RHCLK7 IO_L06P_1/RHCLK6 IO_L05N_1/RHCLK5 IO_L05P_1/RHCLK4 GND IO_L04N_1/RHCLK3 IO_L04P_1/RHCLK2 IO_L03N_1/RHCLK1 IO_L03P_1/RHCLK0 GND IO_L02N_1 IO_L02P_1 VCCINT VCCO_1 IO_L01N_1 IO_L01P_1

52 51

GND DONE

IO_L02P_2/DOUT/BUSY IO_L02N_2/MOSI/CSI_B VCCINT GND IP/VREF_2 VCCO_2 IO_L03P_2/D7/GCLK12 IO_L03N_2/D6/GCLK13 IO/D5 IO_L04P_2/D4/GCLK14 IO_L04N_2/D3/GCLK15 GND IP_L05P_2/RDWR_B/GCLK0 IP_L05N_2/M2/GCLK1 IO_L06P_2/D2/GCLK2 IO_L06N_2/D1/GCLK3 IO/M1 IO_L07P_2/M0 IO_L07N_2/DIN/D0 VCCO_2 VCCAUX IO_L08P_2/VS2 IO_L08N_2/VS1 IO_L09P_2/VS0 IO_L09N_2/CCLK

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

PROG_B IO_L01P_3

DS312-4_02_082009

Figure 80: VQ100 Package Footprint (top view) I/O: Unrestricted, general-purpose user I/O

21

DUAL: Configuration pin, then possible user-I/O

4

VREF: User I/O or input voltage reference for bank

1

INPUT: Unrestricted, general-purpose input pin

24

CLK: User I/O, input, or global buffer input

8

VCCO: Output voltage supply for bank

2

CONFIG: Dedicated configuration pins

JTAG: Dedicated JTAG port pins

4

VCCINT: Internal core supply voltage (+1.2V)

0

N.C.: Not connected

GND: Ground

4

VCCAUX: Auxiliary supply voltage (+2.5V)

16

DS312 (v4.1) July 19, 2013 Product Specification

4 12

www.xilinx.com 166

Spartan-3E FPGA Family: Pinout Descriptions

CP132: 132-ball Chip-scale Package The XC3S100E, XC3S250E and the XC3S500E FPGAs are available in the 132-ball chip-scale package, CP132. The devices share a common footprint for this package as shown in Table 133 and Figure 81. Table 133 lists all the CP132 package pins. They are sorted by bank number and then by pin name. Pins that form a differential I/O pair appear together in the table. The table also shows the pin number for each pin and the pin type, as defined earlier. Physically, the D14 and K2 balls on the XC3S100E and XC3S250E FPGAs are not connected but should be connected to VCCINT to maintain density migration compatibility.

Similarly, the A4, C1, and P10 balls on the XC3S100E FPGA are not connected but should be connected to GND to maintain density migration compatibility. The XC3S100E FPGA has four fewer BPI address pins, A[19:0], whereas the XC3S250E and XC3S500E support A[23:0]. An electronic version of this package pinout table and footprint diagram is available for download from the Xilinx web site at: http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip

Pinout Table Table 133: CP132 Package Pinout XC3S250E XC3S500E Pin Name

XC3S100E Pin Name

Bank

CP132 Ball

Type

0

IO_L01N_0

IO_L01N_0

C12

I/O

0

IO_L01P_0

IO_L01P_0

A13

I/O

0

N.C. ()

IO_L02N_0

A12

100E: N.C. Others: I/O

0

N.C. ()

IO_L02P_0

B12

100E: N.C. Others: I/O

0

N.C. ()

IO_L03N_0/VREF_0

B11

100E: N.C. Others: VREF (I/O)

0

IP

IO_L03P_0

C11

100E: INPUT Others: I/O

0

IO_L04N_0/GCLK5

IO_L04N_0/GCLK5

C9

GCLK

0

IO_L04P_0/GCLK4

IO_L04P_0/GCLK4

A10

GCLK

0

IO_L05N_0/GCLK7

IO_L05N_0/GCLK7

A9

GCLK

0

IO_L05P_0/GCLK6

IO_L05P_0/GCLK6

B9

GCLK

0

IO_L07N_0/GCLK11

IO_L07N_0/GCLK11

B7

GCLK

0

IO_L07P_0/GCLK10

IO_L07P_0/GCLK10

A7

GCLK

0

IO_L08N_0/VREF_0

IO_L08N_0/VREF_0

C6

VREF

0

IO_L08P_0

IO_L08P_0

B6

I/O

0

IO_L09N_0

IO_L09N_0

C5

I/O

0

IO_L09P_0

IO_L09P_0

B5

I/O

0

N.C. ()

IO_L10N_0

C4

100E: N.C. Others: I/O

0

IP

IO_L10P_0

B4

100E: INPUT Others: I/O

0

IO_L11N_0/HSWAP

IO_L11N_0/HSWAP

B3

DUAL

0

IO_L11P_0

IO_L11P_0

A3

I/O

0

IP_L06N_0/GCLK9

IP_L06N_0/GCLK9

C8

GCLK

0

IP_L06P_0/GCLK8

IP_L06P_0/GCLK8

B8

GCLK

0

VCCO_0

VCCO_0

A6

VCCO

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 167

Spartan-3E FPGA Family: Pinout Descriptions Table 133: CP132 Package Pinout (Cont’d) XC3S250E XC3S500E Pin Name

XC3S100E Pin Name

Bank

CP132 Ball

Type

0

VCCO_0

VCCO_0

B10

VCCO

1

IO/A0

IO/A0

F12

DUAL

1

IO/VREF_1

IO/VREF_1

K13

VREF

1

IO_L01N_1/A15

IO_L01N_1/A15

N14

DUAL

1

IO_L01P_1/A16

IO_L01P_1/A16

N13

DUAL

1

IO_L02N_1/A13

IO_L02N_1/A13

M13

DUAL

1

IO_L02P_1/A14

IO_L02P_1/A14

M12

DUAL

1

IO_L03N_1/A11

IO_L03N_1/A11

L14

DUAL

1

IO_L03P_1/A12

IO_L03P_1/A12

L13

DUAL

1

IO_L04N_1/A9/RHCLK1

IO_L04N_1/A9/RHCLK1

J12

RHCLK/DUAL

1

IO_L04P_1/A10/RHCLK0

IO_L04P_1/A10/RHCLK0

K14

RHCLK/DUAL

1

IO_L05N_1/A7/RHCLK3/TRDY1

IO_L05N_1/A7/RHCLK3/TRDY1

J14

RHCLK/DUAL

1

IO_L05P_1/A8/RHCLK2

IO_L05P_1/A8/RHCLK2

J13

RHCLK/DUAL

1

IO_L06N_1/A5/RHCLK5

IO_L06N_1/A5/RHCLK5

H12

RHCLK/DUAL

1

IO_L06P_1/A6/RHCLK4/IRDY1

IO_L06P_1/A6/RHCLK4/IRDY1

H13

RHCLK/DUAL

1

IO_L07N_1/A3/RHCLK7

IO_L07N_1/A3/RHCLK7

G13

RHCLK/DUAL

1

IO_L07P_1/A4/RHCLK6

IO_L07P_1/A4/RHCLK6

G14

RHCLK/DUAL

1

IO_L08N_1/A1

IO_L08N_1/A1

F13

DUAL

1

IO_L08P_1/A2

IO_L08P_1/A2

F14

DUAL

1

IO_L09N_1/LDC0

IO_L09N_1/LDC0

D12

DUAL

1

IO_L09P_1/HDC

IO_L09P_1/HDC

D13

DUAL

1

IO_L10N_1/LDC2

IO_L10N_1/LDC2

C13

DUAL

1

IO_L10P_1/LDC1

IO_L10P_1/LDC1

C14

DUAL

1

IP/VREF_1

IP/VREF_1

G12

VREF

1

VCCO_1

VCCO_1

E13

VCCO

1

VCCO_1

VCCO_1

M14

VCCO

2

IO/D5

IO/D5

P4

DUAL

2

IO/M1

IO/M1

N7

DUAL

2

IP/VREF_2

IO/VREF_2

P11

100E: VREF(INPUT) Others: VREF(I/O)

2

IO_L01N_2/INIT_B

IO_L01N_2/INIT_B

N1

DUAL

2

IO_L01P_2/CSO_B

IO_L01P_2/CSO_B

M2

DUAL

2

IO_L02N_2/MOSI/CSI_B

IO_L02N_2/MOSI/CSI_B

N2

DUAL

2

IO_L02P_2/DOUT/BUSY

IO_L02P_2/DOUT/BUSY

P1

DUAL

2

IO_L03N_2/D6/GCLK13

IO_L03N_2/D6/GCLK13

N4

DUAL/GCLK

2

IO_L03P_2/D7/GCLK12

IO_L03P_2/D7/GCLK12

M4

DUAL/GCLK

2

IO_L04N_2/D3/GCLK15

IO_L04N_2/D3/GCLK15

N5

DUAL/GCLK

2

IO_L04P_2/D4/GCLK14

IO_L04P_2/D4/GCLK14

M5

DUAL/GCLK

2

IO_L06N_2/D1/GCLK3

IO_L06N_2/D1/GCLK3

P7

DUAL/GCLK

2

IO_L06P_2/D2/GCLK2

IO_L06P_2/D2/GCLK2

P6

DUAL/GCLK

2

IO_L07N_2/DIN/D0

IO_L07N_2/DIN/D0

N8

DUAL

2

IO_L07P_2/M0

IO_L07P_2/M0

P8

DUAL

2

N.C. ()

IO_L08N_2/A22

M9

100E: N.C. Others: DUAL

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 168

Spartan-3E FPGA Family: Pinout Descriptions Table 133: CP132 Package Pinout (Cont’d) XC3S250E XC3S500E Pin Name

XC3S100E Pin Name

Bank

CP132 Ball

Type

2

N.C. ()

IO_L08P_2/A23

N9

100E: N.C. Others: DUAL

2

N.C. ()

IO_L09N_2/A20

M10

100E: N.C. Others: DUAL

2

N.C. ()

IO_L09P_2/A21

N10

100E: N.C. Others: DUAL

2

IO_L10N_2/VS1/A18

IO_L10N_2/VS1/A18

M11

DUAL

2

IO_L10P_2/VS2/A19

IO_L10P_2/VS2/A19

N11

DUAL

2

IO_L11N_2/CCLK

IO_L11N_2/CCLK

N12

DUAL

2

IO_L11P_2/VS0/A17

IO_L11P_2/VS0/A17

P12

DUAL

2

IP/VREF_2

IP/VREF_2

N3

VREF

2

IP_L05N_2/M2/GCLK1

IP_L05N_2/M2/GCLK1

N6

DUAL/GCLK

2

IP_L05P_2/RDWR_B/GCLK0

IP_L05P_2/RDWR_B/GCLK0

M6

DUAL/GCLK

2

VCCO_2

VCCO_2

M8

VCCO

2

VCCO_2

VCCO_2

P3

VCCO

3

IO

IO

J3

I/O

3

IP/VREF_3

IO/VREF_3

K3

100E: VREF(INPUT) Others: VREF(I/O)

3

IO_L01N_3

IO_L01N_3

B1

I/O

3

IO_L01P_3

IO_L01P_3

B2

I/O

3

IO_L02N_3

IO_L02N_3

C2

I/O

3

IO_L02P_3

IO_L02P_3

C3

I/O

3

N.C. ()

IO_L03N_3

D1

100E: N.C. Others: I/O

3

IO

IO_L03P_3

D2

I/O

3

IO_L04N_3/LHCLK1

IO_L04N_3/LHCLK1

F2

LHCLK

3

IO_L04P_3/LHCLK0

IO_L04P_3/LHCLK0

F3

LHCLK

3

IO_L05N_3/LHCLK3/IRDY2

IO_L05N_3/LHCLK3/IRDY2

G1

LHCLK

3

IO_L05P_3/LHCLK2

IO_L05P_3/LHCLK2

F1

LHCLK

3

IO_L06N_3/LHCLK5

IO_L06N_3/LHCLK5

H1

LHCLK

3

IO_L06P_3/LHCLK4/TRDY2

IO_L06P_3/LHCLK4/TRDY2

G3

LHCLK

3

IO_L07N_3/LHCLK7

IO_L07N_3/LHCLK7

H3

LHCLK

3

IO_L07P_3/LHCLK6

IO_L07P_3/LHCLK6

H2

LHCLK

3

IO_L08N_3

IO_L08N_3

L2

I/O

3

IO_L08P_3

IO_L08P_3

L1

I/O

3

IO_L09N_3

IO_L09N_3

M1

I/O

3

IO_L09P_3

IO_L09P_3

L3

I/O

3

IP/VREF_3

IP/VREF_3

E2

VREF

3

VCCO_3

VCCO_3

E1

VCCO

3

VCCO_3

VCCO_3

J2

VCCO

GND

N.C. (GND)

GND

A4

GND

GND

GND

GND

A8

GND

GND

N.C. (GND)

GND

C1

GND

GND

GND

GND

C7

GND

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 169

Spartan-3E FPGA Family: Pinout Descriptions Table 133: CP132 Package Pinout (Cont’d) XC3S250E XC3S500E Pin Name

XC3S100E Pin Name

Bank

CP132 Ball

Type

GND

GND

GND

C10

GND

GND

GND

GND

E3

GND

GND

GND

GND

E14

GND

GND

GND

GND

G2

GND

GND

GND

GND

H14

GND

GND

GND

GND

J1

GND

GND

GND

GND

K12

GND

GND

GND

GND

M3

GND

GND

GND

GND

M7

GND

GND

GND

GND

P5

GND

GND

N.C. (GND)

GND

P10

GND

GND

GND

GND

P14

GND

DONE

DONE

P13

CONFIG

VCCAUX VCCAUX

PROG_B

PROG_B

A1

CONFIG

VCCAUX

TCK

TCK

B13

JTAG

VCCAUX

TDI

TDI

A2

JTAG

VCCAUX

TDO

TDO

A14

JTAG

VCCAUX

TMS

TMS

B14

JTAG

VCCAUX

VCCAUX

VCCAUX

A5

VCCAUX

VCCAUX

VCCAUX

VCCAUX

E12

VCCAUX

VCCAUX

VCCAUX

VCCAUX

K1

VCCAUX

VCCAUX

VCCAUX

VCCAUX

P9

VCCAUX

VCCINT

VCCINT

VCCINT

A11

VCCINT

VCCINT

VCCINT

VCCINT

D3

VCCINT

VCCINT

N.C. (VCCINT)

VCCINT

D14

VCCINT

VCCINT

N.C. (VCCINT)

VCCINT

K2

VCCINT

VCCINT

VCCINT

VCCINT

L12

VCCINT

VCCINT

VCCINT

VCCINT

P2

VCCINT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 170

Spartan-3E FPGA Family: Pinout Descriptions

User I/Os by Bank Table 134 shows how the 83 available user-I/O pins are distributed on the XC3S100E FPGA packaged in the CP132 package. Table 135 indicates how the 92 available user-I/O

pins are distributed on the XC3S250E and the XC3S500E FPGAs in the CP132 package.

Table 134: User I/Os Per Bank for the XC3S100E in the CP132 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

18

6

2

1

1

8

1

23

0

0

21

2

0(2)

Bottom

2

22

0

0

20

2

0(2)

Left

3

20

10

0

0

2

8

83

16

2

42

7

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

Table 135: User I/Os Per Bank for the XC3S250E and XC3S500E in the CP132 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

22

11

0

1

2

8

1

23

0

0

21

2

0(2)

Bottom

2

26

0

0

24

2

0(2)

Left

3

21

11

0

0

2

8

92

22

0

46

8

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 171

Spartan-3E FPGA Family: Pinout Descriptions

Footprint Migration Differences Table 136 summarizes any footprint and functionality differences between the XC3S100E, the XC3S250E, and the XC3S500E FPGAs that may affect easy migration between devices in the CP132 package. There are 14 such balls. All other pins not listed in Table 136 unconditionally migrate between Spartan-3E devices available in the CP132 package.

the two pins have identical functionality. A left-facing arrow () indicates that the pin on the device on the right unconditionally migrates to the pin on the device on the left. It may be possible to migrate the opposite direction depending on the I/O configuration. For example, an I/O pin (Type = I/O) can migrate to an input-only pin (Type = INPUT) if the I/O pin is configured as an input.

The XC3S100E is duplicated on both the left and right sides of the table to show migrations to and from the XC3S250E and the XC3S500E. The arrows indicate the direction for easy migration. A double-ended arrow () indicates that

The XC3S100E FPGA in the CP132 package has four fewer BPI-mode address lines than the XC3S250E and XC3S500E.

Table 136: CP132 Footprint Migration Differences CP132 Ball

Bank

A12

0

B4

XC3S100E Type

Migration

XC3S250E Type

Migration

XC3S500E Type

Migration

N.C.



I/O



I/O



N.C.

0

INPUT



I/O



I/O



INPUT

B11

0

N.C.



I/O



I/O



N.C.

B12

0

N.C.



I/O



I/O



N.C.

C4

0

N.C.



I/O



I/O



N.C.

C11

0

INPUT



I/O



I/O



INPUT

D1

3

N.C.



I/O



I/O



N.C.

D2

3

I/O



I/O (Diff)



I/O (Diff)



I/O

K3

3

VREF(INPUT)



VREF(I/O)



VREF(I/O)



VREF(INPUT)

M9

2

N.C.



DUAL



DUAL



N.C.

M10

2

N.C.



DUAL



DUAL



N.C.

N9

2

N.C.



DUAL



DUAL



N.C.

N10

2

N.C.



DUAL



DUAL



N.C.

P11

2

VREF(INPUT)



VREF(I/O)



VREF(I/O)



VREF(INPUT)

DIFFERENCES

14

0

XC3S100E Type

14

Legend: 

This pin is identical on the device on the left and the right.



This pin can unconditionally migrate from the device on the left to the device on the right. Migration in the other direction may be possible depending on how the pin is configured for the device on the right.



This pin can unconditionally migrate from the device on the right to the device on the left. Migration in the other direction may be possible depending on how the pin is configured for the device on the left.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 172

Spartan-3E FPGA Family: Pinout Descriptions

CP132 Footprint X-Ref Target - Figure 81

Bank 0

A

B

Bank 3

C

PROG_B

2 TDI

I/O

I/O

L01N_3

L01P_3

GND

3 I/O L11P_0

4 GND

I/O

I/O L10P_0

I/O

I/O L02P_3

6

7

8

I/O

L11N_0 HSWAP

L02N_3

5

 I/O

L10N_0



VCCAUX

VCCO_0

I/O

I/O

L09P_0

L08P_0

I/O L09N_0

L07P_0 GCLK10

10 I/O

L05N_0 GCLK7

L04P_0 GCLK4

I/O

INPUT

I/O

L07N_0 GCLK11

L06P_0 GCLK8

L05P_0 GCLK6

INPUT

I/O

GND

L06N_0 GCLK9

L04N_0 GCLK5

I/O L08N_0 VREF_0

GND

9 I/O

11 VCCINT

I/O VCCO_0

L03N_0 VREF_0



I/O GND

12 I/O

L03P_0



L02N_0



13 I/O L01P_0

14 TDO

I/O L02P_0



I/O L01N_0

TCK

TMS

I/O

I/O

L10N_1 LDC2

L10P_1 LDC1

I/O

I/O

VCCINT

L09N_1 LDC0

L09P_1 HDC

VCCINT

GND

VCCAUX

VCCO_1

GND

D

I/O

I/O

L03N_3

L03P_3

E

VCCO_3

I/O

I/O

I/O

F

L05P_3 LHCLK2

L04N_3 LHCLK1

L04P_3 LHCLK0

G

L05N_3 LHCLK3 IRDY2

GND

L06P_3 LHCLK4 TRDY2

I/O

I/O

I/O

H

L06N_3 LHCLK5

L07P_3 LHCLK6

L07N_3 LHCLK7

L06N_1 A5 RHCLK5

I/O

I/O

J

GND

VCCO_3

I/O

L04N_1 A9 RHCLK1

L05P_1 A8 RHCLK2

L05N_1 A7 RHCLK3 TRDY1

K

VCCAUX

VCCINT

VREF_3

I/O

L04P_1 A10 RHCLK0





INPUT VREF_3

I/O

L

M

I/O

I/O L09P_3

I/O

N

L01N_2 INIT_B

I/O

L02P_2 DOUT BUSY

GND

VCCINT

I/O

I/O

INPUT

L03P_2 D7 GCLK12

L04P_2 D4 GCLK14

L05P_2 RDWR_B GCLK0

INPUT

I/O

I/O

INPUT

L03N_2 D6 GCLK13

L04N_2 D3 GCLK15

VREF_2

I/O

P

I/O

GND

I/O

L02N_2 MOSI CSI_B

VREF_1



L08N_3

L01P_2 CSO_B

INPUT

I/O

I/O

I/O

A0

I/O

L08P_3

L09N_3

I/O

VCCINT VCCO_2

I/O D5

GND

GND

VCCO_2

L05N_2 M2 GCLK1

I/O M1

L07N_2 DIN D0

I/O

I/O

L06P_2 D2 GCLK2

L06N_2 D1 GCLK3

I/O

I/O

L07P_2 M0

I/O

I/O

L08N_2 A22

L09N_2 A20





I/O L10N_2 VS1 A18

I/O

I/O

L08P_2 A23

L09P_2 A21



L10P_2 VS2 A19

VCCAUX

GND

VREF_2



I/O

I/O



Bank 2

I/O

I/O

L08N_1 A1

L08P_1 A2

I/O

I/O

L07N_1 A3 RHCLK7

L07P_1 A4 RHCLK6

I/O

L06P_1 A6 RHCLK4 IRDY1

VREF_1

GND

I/O

I/O

I/O

I/O

L03P_1 A12

L03N_1 A11

I/O

I/O

L02P_1 A14

L02N_1 A13

Bank 1

1

VCCO_1

I/O

I/O

I/O

L11N_2 CCLK

L01P_1 A16

L01N_1 A15

DONE

GND

I/O L11P_2 VS0 A17

DS312-4_07_030206

Figure 81: CP132 Package Footprint (top view)

1622

I/O: Unrestricted, general-purpose user I/O

4246

DUAL: Configuration pin, then possible user I/O

7-8

VREF: User I/O or input voltage reference for bank

0-2

INPUT: Unrestricted, general-purpose input pin

16

CLK: User I/O, input, or global buffer input

8

VCCO: Output voltage supply for bank

JTAG: Dedicated JTAG port pins

6

VCCINT: Internal core supply voltage (+1.2V)

GND: Ground

4

VCCAUX: Auxiliary supply voltage (+2.5V)

2

CONFIG: Dedicated configuration pins

9

N.C.: Unconnected balls on the XC3S100E FPGA ()

DS312 (v4.1) July 19, 2013 Product Specification

4 16

www.xilinx.com 173

Spartan-3E FPGA Family: Pinout Descriptions

TQ144: 144-lead Thin Quad Flat Package The XC3S100E and the XC3S250E FPGAs are available in the 144-lead thin quad flat package, TQ144. Both devices share a common footprint for this package as shown in Table 137 and Figure 82.

The TQ144 package only supports 20 address output pins in the Byte-wide Peripheral Interface (BPI) configuration mode. In larger packages, there are 24 BPI address outputs.

Table 137 lists all the package pins. They are sorted by bank number and then by pin name of the largest device. Pins that form a differential I/O pair appear together in the table. The table also shows the pin number for each pin and the pin type, as defined earlier.

An electronic version of this package pinout table and footprint diagram is available for download from the Xilinx web site at: http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip

Pinout Table Table 137: TQ144 Package Pinout Bank

XC3S100E Pin Name

XC3S250E Pin Name

TQ144 Pin

Type

0

IO

IO

P132

I/O

0

IO/VREF_0

IO/VREF_0

P124

VREF

0

IO_L01N_0

IO_L01N_0

P113

I/O

0

IO_L01P_0

IO_L01P_0

P112

I/O

0

IO_L02N_0

IO_L02N_0

P117

I/O

0

IO_L02P_0

IO_L02P_0

P116

I/O

0

IO_L04N_0/GCLK5

IO_L04N_0/GCLK5

P123

GCLK

0

IO_L04P_0/GCLK4

IO_L04P_0/GCLK4

P122

GCLK

0

IO_L05N_0/GCLK7

IO_L05N_0/GCLK7

P126

GCLK

0

IO_L05P_0/GCLK6

IO_L05P_0/GCLK6

P125

GCLK

0

IO_L07N_0/GCLK11

IO_L07N_0/GCLK11

P131

GCLK

0

IO_L07P_0/GCLK10

IO_L07P_0/GCLK10

P130

GCLK

0

IO_L08N_0/VREF_0

IO_L08N_0/VREF_0

P135

VREF

0

IO_L08P_0

IO_L08P_0

P134

I/O

0

IO_L09N_0

IO_L09N_0

P140

I/O

0

IO_L09P_0

IO_L09P_0

P139

I/O

0

IO_L10N_0/HSWAP

IO_L10N_0/HSWAP

P143

DUAL

0

IO_L10P_0

IO_L10P_0

P142

I/O

0

IP

IP

P111

INPUT

0

IP

IP

P114

INPUT

0

IP

IP

P136

INPUT

0

IP

IP

P141

INPUT

0

IP_L03N_0

IP_L03N_0

P120

INPUT

0

IP_L03P_0

IP_L03P_0

P119

INPUT

0

IP_L06N_0/GCLK9

IP_L06N_0/GCLK9

P129

GCLK

0

IP_L06P_0/GCLK8

IP_L06P_0/GCLK8

P128

GCLK

0

VCCO_0

VCCO_0

P121

VCCO

0

VCCO_0

VCCO_0

P138

VCCO

1

IO/A0

IO/A0

P98

DUAL

1

IO/VREF_1

IO/VREF_1

P83

VREF

1

IO_L01N_1/A15

IO_L01N_1/A15

P75

DUAL

1

IO_L01P_1/A16

IO_L01P_1/A16

P74

DUAL

1

IO_L02N_1/A13

IO_L02N_1/A13

P77

DUAL

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 174

Spartan-3E FPGA Family: Pinout Descriptions Table 137: TQ144 Package Pinout (Cont’d) Bank

XC3S100E Pin Name

XC3S250E Pin Name

TQ144 Pin

Type

1

IO_L02P_1/A14

IO_L02P_1/A14

P76

DUAL

1

IO_L03N_1/A11

IO_L03N_1/A11

P82

DUAL

1

IO_L03P_1/A12

IO_L03P_1/A12

P81

DUAL

1

IO_L04N_1/A9/RHCLK1

IO_L04N_1/A9/RHCLK1

P86

RHCLK/DUAL

1

IO_L04P_1/A10/RHCLK0

IO_L04P_1/A10/RHCLK0

P85

RHCLK/DUAL

1

IO_L05N_1/A7/RHCLK3/TRDY1

IO_L05N_1/A7/RHCLK3

P88

RHCLK/DUAL

1

IO_L05P_1/A8/RHCLK2

IO_L05P_1/A8/RHCLK2

P87

RHCLK/DUAL

1

IO_L06N_1/A5/RHCLK5

IO_L06N_1/A5/RHCLK5

P92

RHCLK/DUAL

1

IO_L06P_1/A6/RHCLK4/IRDY1

IO_L06P_1/A6/RHCLK4

P91

RHCLK/DUAL

1

IO_L07N_1/A3/RHCLK7

IO_L07N_1/A3/RHCLK7

P94

RHCLK/DUAL

1

IO_L07P_1/A4/RHCLK6

IO_L07P_1/A4/RHCLK6

P93

RHCLK/DUAL

1

IO_L08N_1/A1

IO_L08N_1/A1

P97

DUAL

1

IO_L08P_1/A2

IO_L08P_1/A2

P96

DUAL

1

IO_L09N_1/LDC0

IO_L09N_1/LDC0

P104

DUAL

1

IO_L09P_1/HDC

IO_L09P_1/HDC

P103

DUAL

1

IO_L10N_1/LDC2

IO_L10N_1/LDC2

P106

DUAL

1

IO_L10P_1/LDC1

IO_L10P_1/LDC1

P105

DUAL

1

IP

IP

P78

INPUT

1

IP

IP

P84

INPUT

1

IP

IP

P89

INPUT

1

IP

IP

P101

INPUT

1

IP

IP

P107

INPUT

1

IP/VREF_1

IP/VREF_1

P95

VREF

1

VCCO_1

VCCO_1

P79

VCCO

1

VCCO_1

VCCO_1

P100

VCCO

2

IO/D5

IO/D5

P52

DUAL

2

IO/M1

IO/M1

P60

DUAL

2

IP/VREF_2

IO/VREF_2

P66

100E: VREF(INPUT) 250E: VREF(I/O)

2

IO_L01N_2/INIT_B

IO_L01N_2/INIT_B

P40

DUAL

2

IO_L01P_2/CSO_B

IO_L01P_2/CSO_B

P39

DUAL

2

IO_L02N_2/MOSI/CSI_B

IO_L02N_2/MOSI/CSI_B

P44

DUAL

2

IO_L02P_2/DOUT/BUSY

IO_L02P_2/DOUT/BUSY

P43

DUAL

2

IO_L04N_2/D6/GCLK13

IO_L04N_2/D6/GCLK13

P51

DUAL/GCLK

2

IO_L04P_2/D7/GCLK12

IO_L04P_2/D7/GCLK12

P50

DUAL/GCLK

2

IO_L05N_2/D3/GCLK15

IO_L05N_2/D3/GCLK15

P54

DUAL/GCLK

2

IO_L05P_2/D4/GCLK14

IO_L05P_2/D4/GCLK14

P53

DUAL/GCLK

2

IO_L07N_2/D1/GCLK3

IO_L07N_2/D1/GCLK3

P59

DUAL/GCLK

2

IO_L07P_2/D2/GCLK2

IO_L07P_2/D2/GCLK2

P58

DUAL/GCLK

2

IO_L08N_2/DIN/D0

IO_L08N_2/DIN/D0

P63

DUAL

2

IO_L08P_2/M0

IO_L08P_2/M0

P62

DUAL

2

IO_L09N_2/VS1/A18

IO_L09N_2/VS1/A18

P68

DUAL

2

IO_L09P_2/VS2/A19

IO_L09P_2/VS2/A19

P67

DUAL

2

IO_L10N_2/CCLK

IO_L10N_2/CCLK

P71

DUAL

2

IO_L10P_2/VS0/A17

IO_L10P_2/VS0/A17

P70

DUAL

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 175

Spartan-3E FPGA Family: Pinout Descriptions Table 137: TQ144 Package Pinout (Cont’d) Bank

XC3S100E Pin Name

XC3S250E Pin Name

TQ144 Pin

Type

2

IP

IP

P38

INPUT

2

IP

IP

P41

INPUT

2

IP

IP

P69

INPUT

2

IP_L03N_2/VREF_2

IP_L03N_2/VREF_2

P48

VREF

2

IP_L03P_2

IP_L03P_2

P47

INPUT

2

IP_L06N_2/M2/GCLK1

IP_L06N_2/M2/GCLK1

P57

DUAL/GCLK

2

IP_L06P_2/RDWR_B/GCLK0

IP_L06P_2/RDWR_B/GCLK0

P56

DUAL/GCLK

2

VCCO_2

VCCO_2

P42

VCCO

2

VCCO_2

VCCO_2

P49

VCCO

2

VCCO_2

VCCO_2

P64

VCCO

3

IP/VREF_3

IO/VREF_3

P31

100E: VREF(INPUT) 250E: VREF(I/O)

3

IO_L01N_3

IO_L01N_3

P3

I/O

3

IO_L01P_3

IO_L01P_3

P2

I/O

3

IO_L02N_3/VREF_3

IO_L02N_3/VREF_3

P5

VREF

3

IO_L02P_3

IO_L02P_3

P4

I/O

3

IO_L03N_3

IO_L03N_3

P8

I/O

3

IO_L03P_3

IO_L03P_3

P7

I/O

3

IO_L04N_3/LHCLK1

IO_L04N_3/LHCLK1

P15

LHCLK

3

IO_L04P_3/LHCLK0

IO_L04P_3/LHCLK0

P14

LHCLK

3

IO_L05N_3/LHCLK3/IRDY2

IO_L05N_3/LHCLK3

P17

LHCLK

3

IO_L05P_3/LHCLK2

IO_L05P_3/LHCLK2

P16

LHCLK

3

IO_L06N_3/LHCLK5

IO_L06N_3/LHCLK5

P21

LHCLK

3

IO_L06P_3/LHCLK4/TRDY2

IO_L06P_3/LHCLK4

P20

LHCLK

3

IO_L07N_3/LHCLK7

IO_L07N_3/LHCLK7

P23

LHCLK

3

IO_L07P_3/LHCLK6

IO_L07P_3/LHCLK6

P22

LHCLK

3

IO_L08N_3

IO_L08N_3

P26

I/O

3

IO_L08P_3

IO_L08P_3

P25

I/O

3

IO_L09N_3

IO_L09N_3

P33

I/O

3

IO_L09P_3

IO_L09P_3

P32

I/O

3

IO_L10N_3

IO_L10N_3

P35

I/O

3

IO_L10P_3

IO_L10P_3

P34

I/O

3

IP

IP

P6

INPUT

3

IO

IP

P10

100E: I/O 250E: INPUT

3

IP

IP

P18

INPUT

3

IP

IP

P24

INPUT

3

IO

IP

P29

100E: I/O 250E: INPUT

3

IP

IP

P36

INPUT

3

IP/VREF_3

IP/VREF_3

P12

VREF

3

VCCO_3

VCCO_3

P13

VCCO

3

VCCO_3

VCCO_3

P28

VCCO

GND

GND

GND

P11

GND

GND

GND

GND

P19

GND

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 176

Spartan-3E FPGA Family: Pinout Descriptions Table 137: TQ144 Package Pinout (Cont’d) Bank

XC3S100E Pin Name

XC3S250E Pin Name

TQ144 Pin

Type

GND

GND

GND

P27

GND

GND

GND

GND

P37

GND

GND

GND

GND

P46

GND

GND

GND

GND

P55

GND

GND

GND

GND

P61

GND

GND

GND

GND

P73

GND

GND

GND

GND

P90

GND

GND

GND

GND

P99

GND

GND

GND

GND

P118

GND

GND

GND

GND

P127

GND

GND

GND

GND

P133

GND

VCCAUX

DONE

DONE

P72

CONFIG

VCCAUX

PROG_B

PROG_B

P1

CONFIG

VCCAUX

TCK

TCK

P110

JTAG

VCCAUX

TDI

TDI

P144

JTAG

VCCAUX

TDO

TDO

P109

JTAG

VCCAUX

TMS

TMS

P108

JTAG

VCCAUX

VCCAUX

VCCAUX

P30

VCCAUX

VCCAUX

VCCAUX

VCCAUX

P65

VCCAUX

VCCAUX

VCCAUX

VCCAUX

P102

VCCAUX

VCCAUX

VCCAUX

VCCAUX

P137

VCCAUX

VCCINT

VCCINT

VCCINT

P9

VCCINT

VCCINT

VCCINT

VCCINT

P45

VCCINT

VCCINT

VCCINT

VCCINT

P80

VCCINT

VCCINT

VCCINT

VCCINT

P115

VCCINT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 177

Spartan-3E FPGA Family: Pinout Descriptions

User I/Os by Bank Table 138 and Table 139 indicate how the 108 available user-I/O pins are distributed between the four I/O banks on the TQ144 package. Table 138: User I/Os Per Bank for the XC3S100E in the TQ144 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

26

9

6

1

2

8

1

28

0

5

21

2

0(2)

Bottom

2

26

0

4

20

2

0(2)

Left

3

28

13

4

0

3

8

108

22

19

42

9

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

Table 139: User I/Os Per Bank for the XC3S250E in TQ144 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

26

9

6

1

2

8

1

28

0

5

21

2

0(2)

Bottom

2

26

0

4

20

2

0(2)

Left

3

28

11

6

0

3

8

108

20

21

42

9

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

Footprint Migration Differences Table 140 summarizes any footprint and functionality differences between the XC3S100E and the XC3S250E FPGAs that may affect easy migration between devices. There are four such pins. All other pins not listed in Table 140 unconditionally migrate between Spartan-3E devices available in the TQ144 package.

The arrows indicate the direction for easy migration. For example, a left-facing arrow indicates that the pin on the XC3S250E unconditionally migrates to the pin on the XC3S100E. It may be possible to migrate the opposite direction depending on the I/O configuration. For example, an I/O pin (Type = I/O) can migrate to an input-only pin (Type = INPUT) if the I/O pin is configured as an input.

Table 140: TQ144 Footprint Migration Differences TQ144 Pin

Bank

P10

3

P29 P31 P66

XC3S100E Type

Migration

XC3S250E Type

I/O



INPUT

3

I/O



INPUT

3

VREF(INPUT)



VREF(I/O)

2

VREF(INPUT)



VREF(I/O)

DIFFERENCES

4

Legend: 

This pin can unconditionally migrate from the device on the left to the device on the right. Migration in the other direction may be possible depending on how the pin is configured for the device on the right.



This pin can unconditionally migrate from the device on the right to the device on the left. Migration in the other direction may be possible depending on how the pin is configured for the device on the left.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 178

Spartan-3E FPGA Family: Pinout Descriptions

TQ144 Footprint Note pin 1 indicator in top-left corner and logo orientation. Double arrows () indicates a pinout migration difference between the XC3S100E and XC3S250E.

PROG_B IO_L01P_3

1 2

110 TCK 109 TDO

112 IO_L01P_0 111 IP

114 IP 113 IO_L01N_0

116 IO_L02P_0 115 VCCINT

118 GND 117 IO_L02N_0

120 IP_L03N_0 119 IP_L03P_0

122 IO_L04P_0/GCLK4 121 VCCO_0

124 IO/VREF_0 123 IO_L04N_0/GCLK5

126 IO_L05N_0/GCLK7 125 IO_L05P_0/GCLK6

Bank 0

108 TMS 107 IP

Bank 2

106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73

Bank 1

IO_L01N_3 IO_L02P_3 IO_L02N_3/VREF_3 IP IO_L03P_3 IO_L03N_3 VCCINT ( )  IP

37 38

39 40

41 42

43 44

45 46

47 48

49 50

51 52

53 54

55 56

57 58

59 60

61 62

63 64

65 66

67 68

69 70

71 72

GND IP

IO_L01P_2/CSO_B IO_L01N_2/INIT_B

IP VCCO_2

IO_L02P_2/DOUT/BUSY IO_L02N_2/MOSI/CSI_B

VCCINT GND

IP_L03P_2 IP_L03N_2/VREF_2

VCCO_2 IO_L04P_2/D7/GCLK12

IO_L04N_2/D6/GCLK13 IO/D5

IO_L05P_2/D4/GCLK14 IO_L05N_2/D3/GCLK15

GND IP_L06P_2/RDWR_B/GCLK0

IP_L06N_2/M2/GCLK1 IO_L07P_2/D2/GCLK2

IO_L07N_2/D1/GCLK3 IO/M1

GND IO_L08P_2/M0

IO_L08N_2/DIN/D0 VCCO_2

VCCAUX ( ) IO/VREF_2 IO_L09P_2/VS2/A19 IO_L09N_2/VS1/A18

IP IO_L10P_2/VS0/A17

IO_L10N_2/CCLK DONE

Bank 3

3 4 5 6 7 8 9 10 GND 11 IP/VREF_3 12 VCCO_3 13 IO_L04P_3/LHCLK0 14 IO_L04N_3/LHCLK1 15 IO_L05P_3/LHCLK2 16 IO_L05N_3/LHCLK3 17 IP 18 GND 19 IO_L06P_3/LHCLK4 20 IO_L06N_3/LHCLK5 21 IO_L07P_3/LHCLK6 22 IO_L07N_3/LHCLK7 23 IP 24 IO_L08P_3 25 IO_L08N_3 26 GND 27 VCCO_3 28 ( )  IP 29 VCCAUX 30 ( )  IO/VREF_3 31 IO_L09P_3 32 IO_L09N_3 33 IO_L10P_3 34 IO_L10N_3 35 IP 36

128 IP_L06P_0/GCLK8 127 GND

130 IO_L07P_0/GCLK10 129 IP_L06N_0/GCLK9

132 IO 131 IO_L07N_0/GCLK11

134 IO_L08P_0 133 GND

136 IP 135 IO_L08N_0/VREF_0

138 VCCO_0 137 VCCAUX

140 IO_L09N_0 139 IO_L09P_0

142 IO_L10P_0 141 IP

144 TDI 143 IO_L10N_0/HSWAP

X-Ref Target - Figure 82

IO_L10N_1/LDC2 IO_L10P_1/LDC1 IO_L09N_1/LDC0 IO_L09P_1/HDC VCCAUX IP VCCO_1 GND IO/A0 IO_L08N_1/A1 IO_L08P_1/A2 IP/VREF_1 IO_L07N_1/A3/RHCLK7 IO_L07P_1/A4/RHCLK6 IO_L06N_1/A5/RHCLK5 IO_L06P_1/A6/RHCLK4 GND IP IO_L05N_1/A7/RHCLK3 IO_L05P_1/A8/RHCLK2 IO_L04N_1/A9/RHCLK1 IO_L04P_1/A10/RHCLK0 IP IO/VREF_1 IO_L03N_1/A11 IO_L03P_1/A12 VCCINT VCCO_1 IP IO_L02N_1/A13 IO_L02P_1/A14 IO_L01N_1/A15 IO_L01P_1/A16 GND

DS312-4_01_082009

Figure 82: TQ144 Package Footprint (top view)

20

I/O: Unrestricted, general-purpose user I/O

42

DUAL: Configuration pin, then possible user I/O

9

VREF: User I/O or input voltage reference for bank

21

INPUT: Unrestricted, general-purpose input pin

16

CLK: User I/O, input, or global buffer input

9

VCCO: Output voltage supply for bank

JTAG: Dedicated JTAG port pins

4

VCCINT: Internal core supply voltage (+1.2V)

GND: Ground

4

VCCAUX: Auxiliary supply voltage (+2.5V)

2

CONFIG: Dedicated configuration pins

0

N.C.: Not connected

DS312 (v4.1) July 19, 2013 Product Specification

4 13

www.xilinx.com 179

Spartan-3E FPGA Family: Pinout Descriptions

PQ208: 208-pin Plastic Quad Flat Package The 208-pin plastic quad flat package, PQ208, supports two different Spartan-3E FPGAs, including the XC3S250E and the XC3S500E.

Table 141: PQ208 Package Pinout (Cont’d) XC3S250E XC3S500E Pin Name

Bank

Table 141 lists all the PQ208 package pins. They are sorted by bank number and then by pin name. Pairs of pins that form a differential I/O pair appear together in the table. The table also shows the pin number for each pin and the pin type, as defined earlier.

PQ208 Pin

Type

0

IO_L15P_0

P202

I/O

0

IO_L16N_0/HSWAP

P206

DUAL

0

IO_L16P_0

P205

I/O

0

IP

P159

INPUT

An electronic version of this package pinout table and footprint diagram is available for download from the Xilinx website at:

0

IP

P169

INPUT

0

IP

P194

INPUT

0

IP

P204

INPUT

http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip

0

IP_L06N_0

P175

INPUT

0

IP_L06P_0

P174

INPUT

0

IP_L09N_0/GCLK9

P184

GCLK

0

IP_L09P_0/GCLK8

P183

GCLK

0

VCCO_0

P176

VCCO

0

VCCO_0

P191

VCCO

0

VCCO_0

P201

VCCO

Pinout Table Table 141: PQ208 Package Pinout XC3S250E XC3S500E Pin Name

Bank

PQ208 Pin

Type

0

IO

P187

I/O

1

IO_L01N_1/A15

P107

DUAL

0

IO/VREF_0

P179

VREF

1

IO_L01P_1/A16

P106

DUAL

IO_L02N_1/A13

P109

DUAL

0

IO_L01N_0

P161

I/O

1

0

IO_L01P_0

P160

I/O

1

IO_L02P_1/A14

P108

DUAL

IO_L03N_1/VREF_1

P113

VREF

0

IO_L02N_0/VREF_0

P163

VREF

1

0

IO_L02P_0

P162

I/O

1

IO_L03P_1

P112

I/O

0

IO_L03N_0

P165

I/O

1

IO_L04N_1

P116

I/O

IO_L04P_1

P115

I/O DUAL

0

IO_L03P_0

P164

I/O

1

0

IO_L04N_0/VREF_0

P168

VREF

1

IO_L05N_1/A11

P120

0

IO_L04P_0

P167

I/O

1

IO_L05P_1/A12

P119

DUAL

IO_L06N_1/VREF_1

P123

VREF

0

IO_L05N_0

P172

I/O

1

0

IO_L05P_0

P171

I/O

1

IO_L06P_1

P122

I/O

IO_L07N_1/A9/RHCLK1

P127

RHCLK/DUAL

0

IO_L07N_0/GCLK5

P178

GCLK

1

0

IO_L07P_0/GCLK4

P177

GCLK

1

IO_L07P_1/A10/RHCLK0

P126

RHCLK/DUAL

0

IO_L08N_0/GCLK7

P181

GCLK

1

IO_L08N_1/A7/RHCLK3

P129

RHCLK/DUAL

1

IO_L08P_1/A8/RHCLK2

P128

RHCLK/DUAL

1

IO_L09N_1/A5/RHCLK5

P133

RHCLK/DUAL

0

IO_L08P_0/GCLK6

P180

GCLK

0

IO_L10N_0/GCLK11

P186

GCLK

0

IO_L10P_0/GCLK10

P185

GCLK

1

IO_L09P_1/A6/RHCLK4

P132

RHCLK/DUAL

IO_L10N_1/A3/RHCLK7

P135

RHCLK/DUAL

0

IO_L11N_0

P190

I/O

1

0

IO_L11P_0

P189

I/O

1

IO_L10P_1/A4/RHCLK6

P134

RHCLK/DUAL

IO_L11N_1/A1

P138

DUAL

0

IO_L12N_0/VREF_0

P193

VREF

1

0

IO_L12P_0

P192

I/O

1

IO_L11P_1/A2

P137

DUAL

0

IO_L13N_0

P197

I/O

1

IO_L12N_1/A0

P140

DUAL

IO_L12P_1

P139

I/O

0

IO_L13P_0

P196

I/O

1

0

IO_L14N_0/VREF_0

P200

VREF

1

IO_L13N_1

P145

I/O

0

IO_L14P_0

P199

I/O

1

IO_L13P_1

P144

I/O

I/O

1

IO_L14N_1

P147

I/O

1

IO_L14P_1

P146

I/O

0

IO_L15N_0

DS312 (v4.1) July 19, 2013 Product Specification

P203

www.xilinx.com 180

Spartan-3E FPGA Family: Pinout Descriptions Table 141: PQ208 Package Pinout (Cont’d) XC3S250E XC3S500E Pin Name

Bank

Table 141: PQ208 Package Pinout (Cont’d)

PQ208 Pin

Type

Bank

XC3S250E XC3S500E Pin Name

PQ208 Pin

Type

1

IO_L15N_1/LDC0

P151

DUAL

2

IO_L16P_2/VS2/A19

P99

DUAL

1

IO_L15P_1/HDC

P150

DUAL

2

IO_L17N_2/CCLK

P103

DUAL

1

IO_L16N_1/LDC2

P153

DUAL

2

IO_L17P_2/VS0/A17

P102

DUAL

1

IO_L16P_1/LDC1

P152

DUAL

2

IP

P54

INPUT

1

IP

P110

INPUT

2

IP

P91

INPUT

1

IP

P118

INPUT

2

IP

P101

INPUT

1

IP

P124

INPUT

2

IP_L02N_2

P58

INPUT

1

IP

P130

INPUT

2

IP_L02P_2

P57

INPUT

1

IP

P142

INPUT

2

IP_L07N_2/VREF_2

P72

VREF

1

IP

P148

INPUT

2

IP_L07P_2

P71

INPUT

1

IP

P154

INPUT

2

IP_L10N_2/M2/GCLK1

P81

DUAL/GCLK

1

IP/VREF_1

P136

VREF

2

DUAL/GCLK

VCCO_1

P114

VCCO

IP_L10P_2/RDWR_B/ GCLK0

P80

1 1

VCCO_1

P125

VCCO

2

VCCO_2

P59

VCCO

VCCO_2

P73

VCCO

1

VCCO_1

P143

VCCO

2

2

IO/D5

P76

DUAL

2

VCCO_2

P88

VCCO

2

IO/M1

P84

DUAL

3

IO/VREF_3

P45

VREF

IO_L01N_3

P3

I/O

2

IO/VREF_2

P98

VREF

3

2

IO_L01N_2/INIT_B

P56

DUAL

3

IO_L01P_3

P2

I/O

IO_L02N_3/VREF_3

P5

VREF

2

IO_L01P_2/CSO_B

P55

DUAL

3

2

IO_L03N_2/MOSI/CSI_B

P61

DUAL

3

IO_L02P_3

P4

I/O

2

IO_L03P_2/DOUT/BUSY

P60

DUAL

3

IO_L03N_3

P9

I/O

IO_L03P_3

P8

I/O

2

IO_L04N_2

P63

I/O

3

2

IO_L04P_2

P62

I/O

3

IO_L04N_3

P12

I/O

2

IO_L05N_2

P65

I/O

3

IO_L04P_3

P11

I/O

IO_L05N_3

P16

I/O

2

IO_L05P_2

P64

I/O

3

2

IO_L06N_2

P69

I/O

3

IO_L05P_3

P15

I/O

IO_L06N_3

P19

I/O

2

IO_L06P_2

P68

I/O

3

2

IO_L08N_2/D6/GCLK13

P75

DUAL/GCLK

3

IO_L06P_3

P18

I/O

2

IO_L08P_2/D7/GCLK12

P74

DUAL/GCLK

3

IO_L07N_3/LHCLK1

P23

LHCLK

IO_L07P_3/LHCLK0

P22

LHCLK

2

IO_L09N_2/D3/GCLK15

P78

DUAL/GCLK

3

2

IO_L09P_2/D4/GCLK14

P77

DUAL/GCLK

3

IO_L08N_3/LHCLK3

P25

LHCLK

2

IO_L11N_2/D1/GCLK3

P83

DUAL/GCLK

3

IO_L08P_3/LHCLK2

P24

LHCLK

IO_L09N_3/LHCLK5

P29

LHCLK

2

IO_L11P_2/D2/GCLK2

P82

DUAL/GCLK

3

2

IO_L12N_2/DIN/D0

P87

DUAL

3

IO_L09P_3/LHCLK4

P28

LHCLK

IO_L10N_3/LHCLK7

P31

LHCLK

2

IO_L12P_2/M0

P86

DUAL

3

2

IO_L13N_2

P90

I/O

3

IO_L10P_3/LHCLK6

P30

LHCLK

2

IO_L13P_2

P89

I/O

3

IO_L11N_3

P34

I/O

IO_L11P_3

P33

I/O

2

IO_L14N_2/A22

P94

DUAL

3

2

IO_L14P_2/A23

P93

DUAL

3

IO_L12N_3

P36

I/O

2

IO_L15N_2/A20

P97

DUAL

3

IO_L12P_3

P35

I/O

IO_L13N_3

P40

I/O

2

IO_L15P_2/A21

P96

DUAL

3

2

IO_L16N_2/VS1/A18

P100

DUAL

3

IO_L13P_3

P39

I/O

3

IO_L14N_3

P42

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 181

Spartan-3E FPGA Family: Pinout Descriptions Table 141: PQ208 Package Pinout (Cont’d) XC3S250E XC3S500E Pin Name

Bank

Table 141: PQ208 Package Pinout (Cont’d)

PQ208 Pin

Type

Bank

XC3S250E XC3S500E Pin Name

PQ208 Pin

Type

3

IO_L14P_3

P41

I/O

VCCAUX VCCAUX

P66

VCCAUX

3

IO_L15N_3

P48

I/O

VCCAUX VCCAUX

P92

VCCAUX

3

IO_L15P_3

P47

I/O

VCCAUX VCCAUX

P111

VCCAUX

3

IO_L16N_3

P50

I/O

VCCAUX VCCAUX

P149

VCCAUX

3

IO_L16P_3

P49

I/O

VCCAUX VCCAUX

P166

VCCAUX

3

IP

P6

INPUT

VCCAUX VCCAUX

P195

VCCAUX

3

IP

P14

INPUT

VCCINT

VCCINT

P13

VCCINT

3

IP

P26

INPUT

VCCINT

VCCINT

P67

VCCINT

3

IP

P32

INPUT

VCCINT

VCCINT

P117

VCCINT

3

IP

P43

INPUT

VCCINT

VCCINT

P170

VCCINT

3

IP

P51

INPUT

3

IP/VREF_3

P20

VREF

3

VCCO_3

P21

VCCO

3

VCCO_3

P38

VCCO

3

VCCO_3

P46

VCCO

GND

GND

P10

GND

GND

GND

P17

GND

GND

GND

P27

GND

GND

GND

P37

GND

GND

GND

P52

GND

GND

GND

P53

GND

GND

GND

P70

GND

GND

GND

P79

GND

GND

GND

P85

GND

GND

GND

P95

GND

GND

GND

P105

GND

GND

GND

P121

GND

GND

GND

P131

GND

GND

GND

P141

GND

GND

GND

P156

GND

GND

GND

P173

GND

GND

GND

P182

GND

GND

GND

P188

GND

GND

GND

P198

GND

GND

GND

P208

GND

P104

CONFIG

P1

CONFIG

VCCAUX TCK

P158

JTAG

VCCAUX TDI

P207

JTAG

VCCAUX TDO

P157

JTAG

VCCAUX TMS

VCCAUX DONE VCCAUX PROG_B

P155

JTAG

VCCAUX VCCAUX

P7

VCCAUX

VCCAUX VCCAUX

P44

VCCAUX

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 182

Spartan-3E FPGA Family: Pinout Descriptions

User I/Os by Bank

Footprint Migration Differences

Table 142 indicates how the 158 available user-I/O pins are distributed between the four I/O banks on the PQ208 package.

The XC3S250E and XC3S500E FPGAs have identical footprints in the PQ208 package. Designs can migrate between the XC3S250E and XC3S500E without further consideration.

Table 142: User I/Os Per Bank for the XC3S250E and XC3S500E in the PQ208 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

38

18

6

1

5

8

1

40

9

7

21

3

0(2)

Bottom

2

40

8

6

24

2

0(2)

Left

3

40

23

6

0

3

8

158

58

25

46

13

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 183

Spartan-3E FPGA Family: Pinout Descriptions

PQ208 Footprint (Left)

190 IO_L11N_0 189 IO_L11P_0 188 GND

187 IO 186 IO_L10N_0/GCLK11 185 IO_L10P_0/GCLK10

184 IP_L09N_0/GCLK9 183 IP_L09P_0/GCLK8 182 GND

71 72

73

74 75

76

77 78

IP_L07P_2 IP_L07N_2/VREF_2

VCCO_2

IO_L08P_2/D7/GCLK12 IO_L08N_2/D6/GCLK13

IO/D5 IO_L09P_2/D4/GCLK14

193 IO_L12N_0/VREF_0 192 IO_L12P_0 191 VCCO_0 68 69 70 IO_L06P_2 IO_L06N_2 GND

IO_L13N_0 IO_L13P_0 VCCAUX IP

GND

79 GND

IO_L09N_2/D3/GCLK15

IO_L05N_2 VCCAUX VCCINT

63

IO_L04N_2 IO_L05P_2

64 65 66 67

61 62 IO_L03N_2/MOSI/CSI_B IO_L04P_2

IO_L03P_2/DOUT/BUSY

58 59 60

Bank 2 GND IP IO_L01P_2/CSO_B

DS312-4_03_030705

198 197 196 195 194

Bank 0

55 56 57

3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

IO_L01N_2/INIT_B IP_L02P_2 IP_L02N_2 VCCO_2

IO_L01N_3 IO_L02P_3 IO_L02N_3/VREF_3 IP VCCAUX IO_L03P_3 IO_L03N_3 GND IO_L04P_3 IO_L04N_3 VCCINT IP IO_L05P_3 IO_L05N_3 GND IO_L06P_3 IO_L06N_3 IP/VREF_3 VCCO_3 IO_L07P_3/LHCLK0 IO_L07N_3/LHCLK1 IO_L08P_3/LHCLK2 IO_L08N_3/LHCLK3 IP GND IO_L09P_3/LHCLK4 IO_L09N_3/LHCLK5 IO_L10P_3/LHCLK6 IO_L10N_3/LHCLK7 IP IO_L11P_3 IO_L11N_3 IO_L12P_3 IO_L12N_3 GND VCCO_3 IO_L13P_3 IO_L13N_3 IO_L14P_3 IO_L14N_3 IP VCCAUX IO/VREF_3 VCCO_3 IO_L15P_3 IO_L15N_3 IO_L16P_3 IO_L16N_3 IP GND

Bank 3

1 2

53 54

PROG_B IO_L01P_3

203 IO_L15N_0 202 IO_L15P_0 201 VCCO_0 200 IO_L14N_0/VREF_0 199 IO_L14P_0

208 GND 207 TDI 206 IO_L16N_0/HSWAP 205 IO_L16P_0 204 IP

X-Ref Target - Figure 83

Figure 83: PQ208 Footprint (Left)

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 184

Spartan-3E FPGA Family: Pinout Descriptions

PQ208 Footprint (Right)

159 IP 158 TCK 157 TDO

163 162 161 160

IO_L04P_0 VCCAUX IO_L03N_0 IO_L03P_0 IO_L02N_0/VREF_0 IO_L02P_0 IO_L01N_0 IO_L01P_0 167 166 165 164

171 IO_L05P_0 170 VCCINT 169 IP 168 IO_L04N_0/VREF_0

173 GND 172 IO_L05N_0

179 IO/VREF_0 178 IO_L07N_0/GCLK5 177 IO_L07P_0/GCLK4 176 VCCO_0 175 IP_L06N_0 174 IP_L06P_0

181 IO_L08N_0/GCLK7 180 IO_L08P_0/GCLK6

X-Ref Target - Figure 84

156 GND 155 TMS

Bank 1

Bank 0

IP IO_L16N_1/LDC2 IO_L16P_1/LDC1 IO_L15N_1/LDC0 IO_L15P_1/HDC VCCAUX IP IO_L14N_1 IO_L14P_1 IO_L13N_1 IO_L13P_1 VCCO_1 IP GND IO_L12N_1/A0 IO_L12P_1 IO_L11N_1/A1 IO_L11P_1/A2 IP/VREF_1 IO_L10N_1/A3/RHCLK7 IO_L10P_1/A4/RHCLK6 IO_L09N_1/A5/RHCLK5 IO_L09P_1/A6/RHCLK4 GND IP IO_L08N_1/A7/RHCLK3 IO_L08P_1/A8/RHCLK2 IO_L07N_1/A9/RHCLK1 IO_L07P_1/A10/RHCLK VCCO_1 IP IO_L06N_1/VREF_1 IO_L06P_1 GND IO_L05N_1/A11 IO_L05P_1/A12 IP VCCINT IO_L04N_1 IO_L04P_1 VCCO_1 IO_L03N_1/VREF_1 IO_L03P_1 VCCAUX IP IO_L02N_1/A13 IO_L02P_1/A14 IO_L01N_1/A15 IO_L01P_1/A16 GND

IO_L17P_2/VS0/A17 102 IO_L17N_2/CCLK 103 DONE 104

97 98 99 IO_L16N_2/VS1/A18 100 IP 101

93 94 95 96

IO_L14P_2/A23 IO_L14N_2/A22 GND IO_L15P_2/A21 IO_L15N_2/A20 IO/VREF_2 IO_L16P_2/VS2/A19

IO_L13N_2 IP VCCAUX

88 89 90 91 92

86 87

83 84 85

IO_L12N_2/DIN/D0 VCCO_2 IO_L13P_2

82 IO_L11P_2/D2/GCLK2

IO_L11N_2/D1/GCLK3 IO/M1

GND IO_L12P_2/M0

80 81 IP_L10P_2/RDWR_B/GCLK0 IP_L10N_2/M2/GCLK1

Bank 2

154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105

DS312-4_04_082009

Figure 84: PQ208 Footprint (Right) DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 185

Spartan-3E FPGA Family: Pinout Descriptions

FT256: 256-ball Fine-pitch, Thin Ball Grid Array The 256-ball fine-pitch, thin ball grid array package, FT256, supports three different Spartan-3E FPGAs, including the XC3S250E, the XC3S500E, and the XC3S1200E. Table 143 lists all the package pins. They are sorted by bank number and then by pin name of the largest device. Pins that form a differential I/O pair appear together in the table. The table also shows the pin number for each pin and the pin type, as defined earlier. The highlighted rows indicate pinout differences between the XC3S250E, the XC3S500E, and the XC3S1200E FPGAs. The XC3S250E has 18 unconnected balls, indicated as N.C. (No Connection) in Table 143 and with the black diamond character () in Table 143 and Figure 83. If the table row is highlighted in tan, then this is an instance where an unconnected pin on the XC3S250E FPGA maps

to a VREF pin on the XC3S500E and XC3S1200E FPGA. If the FPGA application uses an I/O standard that requires a VREF voltage reference, connect the highlighted pin to the VREF voltage supply, even though this does not actually connect to the XC3S250E FPGA. This VREF connection on the board allows future migration to the larger devices without modifying the printed-circuit board. All other balls have nearly identical functionality on all three devices. Table 147 summarizes the Spartan-3E footprint migration differences for the FT256 package. An electronic version of this package pinout table and footprint diagram is available for download from the Xilinx web site at: http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip

Pinout Table Table 143: FT256 Package Pinout Bank

XC3S250E Pin Name

XC3S500E Pin Name

XC3S1200E Pin Name

FT256 Ball

Type

0

IO

IO

IO

A7

I/O

0

IO

IO

IO

A12

I/O

0

IO

IO

IO

B4

I/O

0

IP

IP

IO

B6

250E: INPUT 500E: INPUT 1200E: I/O

0

IP

IP

IO

B10

250E: INPUT 500E: INPUT 1200E: I/O

0

IO/VREF_0

IO/VREF_0

IO/VREF_0

D9

VREF

0

IO_L01N_0

IO_L01N_0

IO_L01N_0

A14

I/O

0

IO_L01P_0

IO_L01P_0

IO_L01P_0

B14

I/O

0

IO_L03N_0/VREF_0

IO_L03N_0/VREF_0

IO_L03N_0/VREF_0

A13

VREF

0

IO_L03P_0

IO_L03P_0

IO_L03P_0

B13

I/O

0

IO_L04N_0

IO_L04N_0

IO_L04N_0

E11

I/O

0

IO_L04P_0

IO_L04P_0

IO_L04P_0

D11

I/O

0

IO_L05N_0/VREF_0

IO_L05N_0/VREF_0

IO_L05N_0/VREF_0

B11

VREF

0

IO_L05P_0

IO_L05P_0

IO_L05P_0

C11

I/O

0

IO_L06N_0

IO_L06N_0

IO_L06N_0

E10

I/O

0

IO_L06P_0

IO_L06P_0

IO_L06P_0

D10

I/O

0

IO_L08N_0/GCLK5

IO_L08N_0/GCLK5

IO_L08N_0/GCLK5

F9

GCLK

0

IO_L08P_0/GCLK4

IO_L08P_0/GCLK4

IO_L08P_0/GCLK4

E9

GCLK

0

IO_L09N_0/GCLK7

IO_L09N_0/GCLK7

IO_L09N_0/GCLK7

A9

GCLK

0

IO_L09P_0/GCLK6

IO_L09P_0/GCLK6

IO_L09P_0/GCLK6

A10

GCLK

0

IO_L11N_0/GCLK11

IO_L11N_0/GCLK11

IO_L11N_0/GCLK11

D8

GCLK

0

IO_L11P_0/GCLK10

IO_L11P_0/GCLK10

IO_L11P_0/GCLK10

C8

GCLK

0

IO_L12N_0

IO_L12N_0

IO_L12N_0

F8

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 186

Spartan-3E FPGA Family: Pinout Descriptions Table 143: FT256 Package Pinout (Cont’d) Bank

XC3S250E Pin Name

XC3S500E Pin Name

XC3S1200E Pin Name

FT256 Ball

Type

0

IO_L12P_0

IO_L12P_0

IO_L12P_0

E8

I/O

0

N.C. ()

IO_L13N_0

IO_L13N_0

C7

250E: N.C. 500E: I/O 1200E: I/O

0

N.C. ()

IO_L13P_0

IO_L13P_0

B7

250E: N.C. 500E: I/O 1200E: I/O

0

IO_L14N_0/VREF_0

IO_L14N_0/VREF_0

IO_L14N_0/VREF_0

D7

VREF

0

IO_L14P_0

IO_L14P_0

IO_L14P_0

E7

I/O

0

IO_L15N_0

IO_L15N_0

IO_L15N_0

D6

I/O

0

IO_L15P_0

IO_L15P_0

IO_L15P_0

C6

I/O

0

IO_L17N_0/VREF_0

IO_L17N_0/VREF_0

IO_L17N_0/VREF_0

A4

VREF

0

IO_L17P_0

IO_L17P_0

IO_L17P_0

A5

I/O

0

IO_L18N_0

IO_L18N_0

IO_L18N_0

C4

I/O

0

IO_L18P_0

IO_L18P_0

IO_L18P_0

C5

I/O

0

IO_L19N_0/HSWAP

IO_L19N_0/HSWAP

IO_L19N_0/HSWAP

B3

DUAL

0

IO_L19P_0

IO_L19P_0

IO_L19P_0

C3

I/O

0

IP

IP

IP

A3

INPUT

0

IP

IP

IP

C13

INPUT

0

IP_L02N_0

IP_L02N_0

IP_L02N_0

C12

INPUT

0

IP_L02P_0

IP_L02P_0

IP_L02P_0

D12

INPUT

0

IP_L07N_0

IP_L07N_0

IP_L07N_0

C9

INPUT

0

IP_L07P_0

IP_L07P_0

IP_L07P_0

C10

INPUT

0

IP_L10N_0/GCLK9

IP_L10N_0/GCLK9

IP_L10N_0/GCLK9

B8

GCLK

0

IP_L10P_0/GCLK8

IP_L10P_0/GCLK8

IP_L10P_0/GCLK8

A8

GCLK

0

IP_L16N_0

IP_L16N_0

IP_L16N_0

E6

INPUT

0

IP_L16P_0

IP_L16P_0

IP_L16P_0

D5

INPUT

0

VCCO_0

VCCO_0

VCCO_0

B5

VCCO

0

VCCO_0

VCCO_0

VCCO_0

B12

VCCO

0

VCCO_0

VCCO_0

VCCO_0

F7

VCCO

0

VCCO_0

VCCO_0

VCCO_0

F10

VCCO

1

IO_L01N_1/A15

IO_L01N_1/A15

IO_L01N_1/A15

R15

DUAL

1

IO_L01P_1/A16

IO_L01P_1/A16

IO_L01P_1/A16

R16

DUAL

1

IO_L02N_1/A13

IO_L02N_1/A13

IO_L02N_1/A13

P15

DUAL

1

IO_L02P_1/A14

IO_L02P_1/A14

IO_L02P_1/A14

P16

DUAL

1

N.C. ()

IO_L03N_1/VREF_1

IO_L03N_1/VREF_1

N15

250E: N.C. 500E: VREF 1200E: VREF

1

N.C. ()

IO_L03P_1

IO_L03P_1

N14

250E: N.C. 500E: I/O 1200E: I/O

1

IO_L04N_1/VREF_1

IO_L04N_1/VREF_1

IO_L04N_1/VREF_1

M16

VREF

1

IO_L04P_1

IO_L04P_1

IO_L04P_1

N16

I/O

1

N.C. ()

IO_L05N_1

IO_L05N_1

L13

250E: N.C. 500E: I/O 1200E: I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 187

Spartan-3E FPGA Family: Pinout Descriptions Table 143: FT256 Package Pinout (Cont’d) Bank

XC3S250E Pin Name

XC3S500E Pin Name

XC3S1200E Pin Name

FT256 Ball

Type

1

N.C. ()

IO_L05P_1

IO_L05P_1

L12

250E: N.C. 500E: I/O 1200E: I/O

1

IO_L06N_1

IO_L06N_1

IO_L06N_1

L15

I/O

1

IO_L06P_1

IO_L06P_1

IO_L06P_1

L14

I/O

1

IO_L07N_1/A11

IO_L07N_1/A11

IO_L07N_1/A11

K12

DUAL

1

IO_L07P_1/A12

IO_L07P_1/A12

IO_L07P_1/A12

K13

DUAL

1

IO_L08N_1/VREF_1

IO_L08N_1/VREF_1

IO_L08N_1/VREF_1

K14

VREF

1

IO_L08P_1

IO_L08P_1

IO_L08P_1

K15

I/O

1

IO_L09N_1/A9/RHCLK1

IO_L09N_1/A9/RHCLK1

IO_L09N_1/A9/RHCLK1

J16

RHCLK/DUAL

1

IO_L09P_1/A10/RHCLK0

IO_L09P_1/A10/RHCLK0

IO_L09P_1/A10/RHCLK0

K16

RHCLK/DUAL

1

IO_L10N_1/A7/RHCLK3/ TRDY1

IO_L10N_1/A7/RHCLK3/ TRDY1

IO_L10N_1/A7/RHCLK3/ TRDY1

J13

RHCLK/DUAL

1

IO_L10P_1/A8/RHCLK2

IO_L10P_1/A8/RHCLK2

IO_L10P_1/A8/RHCLK2

J14

RHCLK/DUAL

1

IO_L11N_1/A5/RHCLK5

IO_L11N_1/A5/RHCLK5

IO_L11N_1/A5/RHCLK5

H14

RHCLK/DUAL

1

IO_L11P_1/A6/RHCLK4/ IRDY1

IO_L11P_1/A6/RHCLK4/ IRDY1

IO_L11P_1/A6/RHCLK4/ IRDY1

H15

RHCLK/DUAL

1

IO_L12N_1/A3/RHCLK7

IO_L12N_1/A3/RHCLK7

IO_L12N_1/A3/RHCLK7

H11

RHCLK/DUAL

1

IO_L12P_1/A4/RHCLK6

IO_L12P_1/A4/RHCLK6

IO_L12P_1/A4/RHCLK6

H12

RHCLK/DUAL

1

IO_L13N_1/A1

IO_L13N_1/A1

IO_L13N_1/A1

G16

DUAL

1

IO_L13P_1/A2

IO_L13P_1/A2

IO_L13P_1/A2

G15

DUAL

1

IO_L14N_1/A0

IO_L14N_1/A0

IO_L14N_1/A0

G14

DUAL

1

IO_L14P_1

IO_L14P_1

IO_L14P_1

G13

I/O

1

IO_L15N_1

IO_L15N_1

IO_L15N_1

F15

I/O

1

IO_L15P_1

IO_L15P_1

IO_L15P_1

F14

I/O

1

IO_L16N_1

IO_L16N_1

IO_L16N_1

F12

I/O

1

IO_L16P_1

IO_L16P_1

IO_L16P_1

F13

I/O

1

N.C. ()

IO_L17N_1

IO_L17N_1

E16

250E: N.C. 500E: I/O 1200E: I/O

1

N.C. ().

IO_L17P_1

IO_L17P_1

E13

250E: N.C. 500E: I/O 1200E: I/O

1

IO_L18N_1/LDC0

IO_L18N_1/LDC0

IO_L18N_1/LDC0

D14

DUAL

1

IO_L18P_1/HDC

IO_L18P_1/HDC

IO_L18P_1/HDC

D15

DUAL

1

IO_L19N_1/LDC2

IO_L19N_1/LDC2

IO_L19N_1/LDC2

C15

DUAL

1

IO_L19P_1/LDC1

IO_L19P_1/LDC1

IO_L19P_1/LDC1

C16

DUAL

1

IP

IP

IP

B16

INPUT

1

IP

IP

IP

E14

INPUT

1

IP

IP

IP

G12

INPUT

1

IP

IP

IP

H16

INPUT

1

IP

IP

IP

J11

INPUT

1

IP

IP

IP

J12

INPUT

1

IP

IP

IP

M13

INPUT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 188

Spartan-3E FPGA Family: Pinout Descriptions Table 143: FT256 Package Pinout (Cont’d) Bank

XC3S250E Pin Name

XC3S500E Pin Name

XC3S1200E Pin Name

FT256 Ball

Type

1

IO

IO

IP

M14

250E: I/O 500E: I/O 1200E: INPUT

1

IO/VREF_1

IP/VREF_1

IP/VREF_1

D16

250E: VREF(I/O) 500E: VREF(INPUT) 1200E: VREF(INPUT)

1

IP/VREF_1

IP/VREF_1

IP/VREF_1

H13

VREF

1

VCCO_1

VCCO_1

VCCO_1

E15

VCCO

1

VCCO_1

VCCO_1

VCCO_1

G11

VCCO

1

VCCO_1

VCCO_1

VCCO_1

K11

VCCO

1

VCCO_1

VCCO_1

VCCO_1

M15

VCCO

2

IP

IP

IO

M7

250E: INPUT 500E: INPUT 1200E: I/O

2

IP

IP

IO

T12

250E: INPUT 500E: INPUT 1200E: I/O

2

IO/D5

IO/D5

IO/D5

T8

DUAL

2

IO/M1

IO/M1

IO/M1

T10

DUAL

2

IO/VREF_2

IO/VREF_2

IO/VREF_2

P13

VREF

2

IO/VREF_2

IO/VREF_2

IO/VREF_2

R4

VREF

2

IO_L01N_2/INIT_B

IO_L01N_2/INIT_B

IO_L01N_2/INIT_B

P4

DUAL

2

IO_L01P_2/CSO_B

IO_L01P_2/CSO_B

IO_L01P_2/CSO_B

P3

DUAL

2

IO_L03N_2/MOSI/CSI_B

IO_L03N_2/MOSI/CSI_B

IO_L03N_2/MOSI/CSI_B

N5

DUAL

2

IO_L03P_2/DOUT/BUSY

IO_L03P_2/DOUT/BUSY

IO_L03P_2/DOUT/BUSY

P5

DUAL

2

IO_L04N_2

IO_L04N_2

IO_L04N_2

T5

I/O

2

IO_L04P_2

IO_L04P_2

IO_L04P_2

T4

I/O

2

IO_L05N_2

IO_L05N_2

IO_L05N_2

N6

I/O

2

IO_L05P_2

IO_L05P_2

IO_L05P_2

M6

I/O

2

IO_L06N_2

IO_L06N_2

IO_L06N_2

P6

I/O

2

IO_L06P_2

IO_L06P_2

IO_L06P_2

R6

I/O

2

N.C. ()

IO_L07N_2

IO_L07N_2

P7

250E: N.C. 500E: I/O 1200E: I/O

2

N.C. ()

IO_L07P_2

IO_L07P_2

N7

250E: N.C. 500E: I/O 1200E: I/O

2

IO_L09N_2/D6/GCLK13

IO_L09N_2/D6/GCLK13

IO_L09N_2/D6/GCLK13

L8

DUAL/GCLK

2

IO_L09P_2/D7/GCLK12

IO_L09P_2/D7/GCLK12

IO_L09P_2/D7/GCLK12

M8

DUAL/GCLK

2

IO_L10N_2/D3/GCLK15

IO_L10N_2/D3/GCLK15

IO_L10N_2/D3/GCLK15

P8

DUAL/GCLK

2

IO_L10P_2/D4/GCLK14

IO_L10P_2/D4/GCLK14

IO_L10P_2/D4/GCLK14

N8

DUAL/GCLK

2

IO_L12N_2/D1/GCLK3

IO_L12N_2/D1/GCLK3

IO_L12N_2/D1/GCLK3

N9

DUAL/GCLK

2

IO_L12P_2/D2/GCLK2

IO_L12P_2/D2/GCLK2

IO_L12P_2/D2/GCLK2

P9

DUAL/GCLK

2

IO_L13N_2/DIN/D0

IO_L13N_2/DIN/D0

IO_L13N_2/DIN/D0

M9

DUAL

2

IO_L13P_2/M0

IO_L13P_2/M0

IO_L13P_2/M0

L9

DUAL

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 189

Spartan-3E FPGA Family: Pinout Descriptions Table 143: FT256 Package Pinout (Cont’d) Bank

XC3S250E Pin Name

XC3S500E Pin Name

XC3S1200E Pin Name

FT256 Ball

Type

2

N.C. ()

IO_L14N_2/VREF_2

IO_L14N_2/VREF_2

R10

250E: N.C. 500E: VREF 1200E: VREF

2

N.C. ()

IO_L14P_2

IO_L14P_2

P10

250E: N.C. 500E: I/O 1200E: I/O

2

IO_L15N_2

IO_L15N_2

IO_L15N_2

M10

I/O

2

IO_L15P_2

IO_L15P_2

IO_L15P_2

N10

I/O

2

IO_L16N_2/A22

IO_L16N_2/A22

IO_L16N_2/A22

P11

DUAL

2

IO_L16P_2/A23

IO_L16P_2/A23

IO_L16P_2/A23

R11

DUAL

2

IO_L18N_2/A20

IO_L18N_2/A20

IO_L18N_2/A20

N12

DUAL

2

IO_L18P_2/A21

IO_L18P_2/A21

IO_L18P_2/A21

P12

DUAL

2

IO_L19N_2/VS1/A18

IO_L19N_2/VS1/A18

IO_L19N_2/VS1/A18

R13

DUAL

2

IO_L19P_2/VS2/A19

IO_L19P_2/VS2/A19

IO_L19P_2/VS2/A19

T13

DUAL

2

IO_L20N_2/CCLK

IO_L20N_2/CCLK

IO_L20N_2/CCLK

R14

DUAL

2

IO_L20P_2/VS0/A17

IO_L20P_2/VS0/A17

IO_L20P_2/VS0/A17

P14

DUAL

2

IP

IP

IP

T2

INPUT

2

IP

IP

IP

T14

INPUT

2

IP_L02N_2

IP_L02N_2

IP_L02N_2

R3

INPUT

2

IP_L02P_2

IP_L02P_2

IP_L02P_2

T3

INPUT

2

IP_L08N_2/VREF_2

IP_L08N_2/VREF_2

IP_L08N_2/VREF_2

T7

VREF

2

IP_L08P_2

IP_L08P_2

IP_L08P_2

R7

INPUT

2

IP_L11N_2/M2/GCLK1

IP_L11N_2/M2/GCLK1

IP_L11N_2/M2/GCLK1

R9

DUAL/GCLK

2

IP_L11P_2/RDWR_B/ GCLK0

IP_L11P_2/RDWR_B/ GCLK0

IP_L11P_2/RDWR_B/ GCLK0

T9

DUAL/GCLK

2

IP_L17N_2

IP_L17N_2

IP_L17N_2

M11

INPUT

2

IP_L17P_2

IP_L17P_2

IP_L17P_2

N11

INPUT

2

VCCO_2

VCCO_2

VCCO_2

L7

VCCO

2

VCCO_2

VCCO_2

VCCO_2

L10

VCCO

2

VCCO_2

VCCO_2

VCCO_2

R5

VCCO

2

VCCO_2

VCCO_2

VCCO_2

R12

VCCO

3

IO_L01N_3

IO_L01N_3

IO_L01N_3

B2

I/O

3

IO_L01P_3

IO_L01P_3

IO_L01P_3

B1

I/O

3

IO_L02N_3/VREF_3

IO_L02N_3/VREF_3

IO_L02N_3/VREF_3

C2

VREF

3

IO_L02P_3

IO_L02P_3

IO_L02P_3

C1

I/O

3

IO_L03N_3

IO_L03N_3

IO_L03N_3

E4

I/O

3

IO_L03P_3

IO_L03P_3

IO_L03P_3

E3

I/O

3

N.C. ()

IO_L04N_3/VREF_3

IO_L04N_3/VREF_3

F4

250E: N.C. 500E: VREF 1200E: VREF

3

N.C. ()

IO_L04P_3

IO_L04P_3

F3

250E: N.C. 500E: I/O 1200E: I/O

3

IO_L05N_3

IO_L05N_3

IO_L05N_3

E1

I/O

3

IO_L05P_3

IO_L05P_3

IO_L05P_3

D1

I/O

3

IO_L06N_3

IO_L06N_3

IO_L06N_3

G4

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 190

Spartan-3E FPGA Family: Pinout Descriptions Table 143: FT256 Package Pinout (Cont’d) Bank

XC3S250E Pin Name

XC3S500E Pin Name

XC3S1200E Pin Name

FT256 Ball

Type

3

IO_L06P_3

IO_L06P_3

IO_L06P_3

G5

I/O

3

IO_L07N_3

IO_L07N_3

IO_L07N_3

G2

I/O

3

IO_L07P_3

IO_L07P_3

IO_L07P_3

G3

I/O

3

IO_L08N_3/LHCLK1

IO_L08N_3/LHCLK1

IO_L08N_3/LHCLK1

H6

LHCLK

3

IO_L08P_3/LHCLK0

IO_L08P_3/LHCLK0

IO_L08P_3/LHCLK0

H5

LHCLK

3

IO_L09N_3/LHCLK3/ IRDY2

IO_L09N_3/LHCLK3/ IRDY2

IO_L09N_3/LHCLK3/ IRDY2

H4

LHCLK

3

IO_L09P_3/LHCLK2

IO_L09P_3/LHCLK2

IO_L09P_3/LHCLK2

H3

LHCLK

3

IO_L10N_3/LHCLK5

IO_L10N_3/LHCLK5

IO_L10N_3/LHCLK5

J3

LHCLK

3

IO_L10P_3/LHCLK4/ TRDY2

IO_L10P_3/LHCLK4/ TRDY2

IO_L10P_3/LHCLK4/ TRDY2

J2

LHCLK

3

IO_L11N_3/LHCLK7

IO_L11N_3/LHCLK7

IO_L11N_3/LHCLK7

J4

LHCLK

3

IO_L11P_3/LHCLK6

IO_L11P_3/LHCLK6

IO_L11P_3/LHCLK6

J5

LHCLK

3

IO_L12N_3

IO_L12N_3

IO_L12N_3

K1

I/O

3

IO_L12P_3

IO_L12P_3

IO_L12P_3

J1

I/O

3

IO_L13N_3

IO_L13N_3

IO_L13N_3

K3

I/O

3

IO_L13P_3

IO_L13P_3

IO_L13P_3

K2

I/O

3

N.C. ()

IO_L14N_3/VREF_3

IO_L14N_3/VREF_3

L2

250E: N.C. 500E: VREF 1200E: VREF

3

N.C. ()

IO_L14P_3

IO_L14P_3

L3

250E: N.C. 500E: I/O 1200E: I/O

3

IO_L15N_3

IO_L15N_3

IO_L15N_3

L5

I/O

3

IO_L15P_3

IO_L15P_3

IO_L15P_3

K5

I/O

3

IO_L16N_3

IO_L16N_3

IO_L16N_3

N1

I/O

3

IO_L16P_3

IO_L16P_3

IO_L16P_3

M1

I/O

3

N.C. ()

IO_L17N_3

IO_L17N_3

L4

250E: N.C. 500E: I/O 1200E: I/O

3

N.C. ()

IO_L17P_3

IO_L17P_3

M4

250E: N.C. 500E: I/O 1200E: I/O

3

IO_L18N_3

IO_L18N_3

IO_L18N_3

P1

I/O

3

IO_L18P_3

IO_L18P_3

IO_L18P_3

P2

I/O

3

IO_L19N_3

IO_L19N_3

IO_L19N_3

R1

I/O

3

IO_L19P_3

IO_L19P_3

IO_L19P_3

R2

I/O

3

IP

IP

IP

D2

INPUT

3

IP

IP

IP

F2

INPUT

3

IO

IO

IP

F5

250E: I/O 500E: I/O 1200E: INPUT

3

IP

IP

IP

H1

INPUT

3

IP

IP

IP

J6

INPUT

3

IP

IP

IP

K4

INPUT

3

IP

IP

IP

M3

INPUT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 191

Spartan-3E FPGA Family: Pinout Descriptions Table 143: FT256 Package Pinout (Cont’d) Bank

XC3S250E Pin Name

XC3S500E Pin Name

XC3S1200E Pin Name

FT256 Ball

Type INPUT

3

IP

IP

IP

N3

3

IP/VREF_3

IP/VREF_3

IP/VREF_3

G1

VREF

3

IO/VREF_3

IO/VREF_3

IP/VREF_3

N2

250E: VREF(I/O) 500E: VREF(I/O) 1200E: VREF(INPUT)

3

VCCO_3

VCCO_3

VCCO_3

E2

VCCO

3

VCCO_3

VCCO_3

VCCO_3

G6

VCCO

3

VCCO_3

VCCO_3

VCCO_3

K6

VCCO

3

VCCO_3

VCCO_3

VCCO_3

M2

VCCO

GND

GND

GND

GND

A1

GND

GND

GND

GND

GND

A16

GND

GND

GND

GND

GND

B9

GND

GND

GND

GND

GND

F6

GND

GND

GND

GND

GND

F11

GND

GND

GND

GND

GND

G7

GND

GND

GND

GND

GND

G8

GND

GND

GND

GND

GND

G9

GND

GND

GND

GND

GND

G10

GND

GND

GND

GND

GND

H2

GND

GND

GND

GND

GND

H7

GND

GND

GND

GND

GND

H8

GND

GND

GND

GND

GND

H9

GND

GND

GND

GND

GND

H10

GND

GND

GND

GND

GND

J7

GND

GND

GND

GND

GND

J8

GND

GND

GND

GND

GND

J9

GND

GND

GND

GND

GND

J10

GND

GND

GND

GND

GND

J15

GND

GND

GND

GND

GND

K7

GND

GND

GND

GND

GND

K8

GND

GND

GND

GND

GND

K9

GND

GND

GND

GND

GND

K10

GND

GND

GND

GND

GND

L6

GND

GND

GND

GND

GND

L11

GND

GND

GND

GND

GND

R8

GND

GND

GND

GND

GND

T1

GND

GND

GND

GND

GND

T16

GND

VCCAUX

DONE

DONE

DONE

T15

CONFIG

VCCAUX

PROG_B

PROG_B

PROG_B

D3

CONFIG

VCCAUX

TCK

TCK

TCK

A15

JTAG

VCCAUX

TDI

TDI

TDI

A2

JTAG

VCCAUX

TDO

TDO

TDO

C14

JTAG

VCCAUX

TMS

TMS

TMS

B15

JTAG

VCCAUX

VCCAUX

VCCAUX

VCCAUX

A6

VCCAUX

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 192

Spartan-3E FPGA Family: Pinout Descriptions Table 143: FT256 Package Pinout (Cont’d) Bank

XC3S250E Pin Name

XC3S500E Pin Name

XC3S1200E Pin Name

FT256 Ball

Type

A11

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

F1

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

F16

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

L1

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

L16

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

T6

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

T11

VCCAUX

VCCINT

VCCINT

VCCINT

VCCINT

D4

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

D13

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

E5

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

E12

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

M5

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

M12

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

N4

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

N13

VCCINT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 193

Spartan-3E FPGA Family: Pinout Descriptions

User I/Os by Bank Table 144, Table 145, and Table 146 indicate how the available user-I/O pins are distributed between the four I/O banks on the FT256 package.

The XC3S250E FPGA in the FT256 package has 18 unconnected balls, labeled with an “N.C.” type. These pins are also indicated with the black diamond () symbol in Figure 85.

Table 144: User I/Os Per Bank on XC3S250E in the FT256 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

44

20

10

1

5

8

1

42

10

7

21

4

0(2)

Bottom

2

44

8

9

24

3

0(2)

Left

3

42

24

7

0

3

8

172

62

33

46

15

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

Table 145: User I/Os Per Bank on XC3S500E in the FT256 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

46

22

10

1

5

8

1

48

15

7

21

5

0(2)

Bottom

2

48

11

9

24

4

0(2)

Left

3

48

28

7

0

5

8

190

76

33

46

19

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

.

Table 146: User I/Os Per Bank on XC3S1200E in the FT256 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

46

24

8

1

5

8

1

48

14

8

21

5

0(2)

Bottom

2

48

13

7

24

4

0(2)

Left

3

48

27

8

0

5

8

190

78

31

46

19

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 194

Spartan-3E FPGA Family: Pinout Descriptions

Footprint Migration Differences Table 147 summarizes any footprint and functionality differences between the XC3S250E, the XC3S500E, and the XC3S1200E FPGAs that may affect easy migration between devices in the FG256 package. There are 26 such balls. All other pins not listed in Table 147 unconditionally migrate between Spartan-3E devices available in the FT256 package. The XC3S250E is duplicated on both the left and right sides of the table to show migrations to and from the XC3S500E

and the XC3S1200E. The arrows indicate the direction for easy migration. A double-ended arrow () indicates that the two pins have identical functionality. A left-facing arrow () indicates that the pin on the device on the right unconditionally migrates to the pin on the device on the left. It may be possible to migrate the opposite direction depending on the I/O configuration. For example, an I/O pin (Type = I/O) can migrate to an input-only pin (Type = INPUT) if the I/O pin is configured as an input.

Table 147: FT256 Footprint Migration Differences FT256 Ball

Bank

XC3S250E Type

B6

0

INPUT

B7

0

N.C.

B10

0

INPUT

Migration   

XC3S500E Type

Migration

INPUT I/O INPUT

XC3S1200E Type

Migration

XC3S250E Type



I/O



INPUT



I/O



N.C.



I/O



INPUT

C7

0

N.C.



I/O



I/O



N.C.

D16

1

VREF(I/O)



VREF(INPUT)



VREF(INPUT)



VREF(I/O)

E13

1

N.C.



I/O



I/O



N.C.

E16

1

N.C.



I/O



I/O



N.C.

F3

3

N.C.



I/O



I/O



N.C.

F4

3

N.C.



VREF



VREF



N.C.

F5

3

I/O



INPUT



I/O

L2

3

N.C.



VREF



VREF



N.C.

L3

3

N.C.



I/O



I/O



N.C.

L4

3

N.C.



I/O



I/O



N.C.

L12

1

N.C.



I/O



I/O



N.C.

L13

1

N.C.



I/O



I/O



N.C.

M4

3

N.C.



I/O



I/O



N.C.

M7

2

INPUT



INPUT



I/O



INPUT

M14

1

I/O



I/O



INPUT



I/O

N2

3

VREF(I/O)



VREF(I/O)



VREF(INPUT)



VREF(I/O)



I/O

N7

2

N.C.



I/O



I/O



N.C.

N14

1

N.C.



I/O



I/O



N.C.

N15

1

N.C.



VREF



VREF



N.C.

P7

2

N.C.



I/O



I/O



N.C.

P10

2

N.C.



I/O



I/O



N.C.

R10

2

N.C.



VREF



VREF



N.C.

T12

2

INPUT



INPUT



I/O



INPUT

DIFFERENCES

19

7

26

Legend: 

This pin is identical on the device on the left and the right.



This pin can unconditionally migrate from the device on the left to the device on the right. Migration in the other direction may be possible depending on how the pin is configured for the device on the right.



This pin can unconditionally migrate from the device on the right to the device on the left. Migration in the other direction may be possible depending on how the pin is configured for the device on the left.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 195

Spartan-3E FPGA Family: Pinout Descriptions

FT256 Footprint X-Ref Target - Figure 85

2

3

4 I/O

A

GND

B

I/O

I/O

L01P_3

L01N_3

C

D

E

F

Bank 3

G

I/O L02P_3

I/O L05P_3

I/O L05N_3

VCCAUX

INPUT

L17N_0 VREF_0

L17P_0

I/O

VCCO_0

I/O L19N_0 HSWAP

I/O L02N_3 VREF_3

I/O

I/O

I/O

L18P_0

L15P_0

I/O

I/O

L03P_3

L03N_3

I/O

I/O

L04P_3

L04N_3 VREF_3





I/O

I/O

L10P_0 GCLK8

L09N_0 GCLK7

L09P_0 GCLK6

I/O

INPUT

L13P_0

L10N_0 GCLK9

 I/O

I/O

L13N_0

L11P_0 GCLK10

 I/O

I/O

L14N_0 VREF_0

L11N_0 GCLK11

INPUT

I/O

I/O

L16N_0

L14P_0

L12P_0

GND

VCCO_0

VCCO_3

I/O

GND

INPUT



11

12

I/O VCCAUX

I/O

I/O L05N_0 VREF_0

VCCO_0

INPUT

INPUT

I/O

INPUT

L07N_0

L07P_0

L05P_0

L02N_0

I/O

I/O

I/O

INPUT

VREF_0

L06P_0

L04P_0

L02P_0

I/O L08P_0 GCLK4

13

I/O

I/O

L06N_0

L04N_0

I/O

L12N_0

L08N_0 GCLK5

VCCO_0

GND

GND

GND

GND

GND

VCCO_1

L03N_0 VREF_0

14 I/O L01N_0

I/O

I/O

L03P_0

L01P_0

INPUT

TDO

VCCINT L17P_1

L17N_1



I/O

I/O

I/O

I/O

L16P_1

L15P_1

L15N_1

I/O

I/O

I/O

I/O

L13P_1 A2

L13N_1 A1

I/O

I/O

I/O

I/O

I/O

L08P_3 LHCLK0

L08N_3 LHCLK1

GND

GND

GND

GND

L12N_1 A3 RHCLK7

L12P_1 A4 RHCLK6

INPUT

GND

GND

GND

GND

INPUT

INPUT I/O

I/O

I/O

VCCO_3

GND

GND

GND

GND

VCCO_1

L07N_1 A11

L07P_1 A12

L08N_1 VREF_1

I/O

I/O

I/O

I/O

GND

VCCO_2

L09N_2 D6 GCLK13

L13P_2 M0

VCCO_2

GND

L05P_1

L05N_1





I/O

INPUT

L12P_3

I/O L13N_3

I/O

I/O

I/O

L

VCCAUX

L14N_3 VREF_3

L14P_3

L17N_3







VCCO_3

INPUT

L17P_3

I/O L16P_3

I/O L16N_3

INPUT

I/O L15N_3

I/O VCCINT

 INPUT VREF_3



I/O

I/O

L18N_3

L18P_3

I/O INPUT VCCINT L03N_2 MOSI CSI_B

I/O

I/O

I/O

L01P_2 CSO_B

L01N_2 INIT_B

L03P_2 DOUT BUSY

I/O

I/O

INPUT

I/O

L19N_3

L19P_3

L02N_2

VREF_2

GND

I/O L15P_3

INPUT

VCCO_2

INPUT

I/O

I/O

L02P_2

L04P_2

L04N_2

L14P_1

INPUT VREF_1

I/O

I/O

I/O

L09P_2 D7 GCLK12

L13N_2 DIN D0

I/O

INPUT

L15N_2

L17N_2

I/O

INPUT

L15P_2

L17P_2

L18N_2 A20

I/O

I/O

I/O

L12P_2 D2 GCLK2

L14P_2

L16N_2 A22

L18P_2 A21

INPUT

I/O

L11N_2 M2 GCLK1

L14N_2 VREF_2

L05P_2



I/O

I/O

I/O

I/O

L07P_2



L10P_2 D4 GCLK14

L12N_2 D1 GCLK3

I/O

I/O

I/O

L07N_2

L10N_2 D3 GCLK15

L05N_2

I/O L06N_2



I/O

INPUT

L06P_2

L08P_2

INPUT VCCAUX

L08N_2 VREF_2

GND

I/O D5

INPUT L11P_2 RDWR_B GCLK0





I/O M1

VCCINT INPUT I/O

I/O L16P_2 A23

VCCAUX

L10N_1 A7 RHCLK3 TRDY1

VCCO_2

INPUT



I/O L11N_1 A5 RHCLK5

I/O L08P_1

I/O

I/O L06N_1

INPUT



INPUT I/O

GND

L06P_1



VREF_2

I/O

L11P_1 A6 RHCLK4 IRDY1

I/O L10P_1 A8 RHCLK2

I/O VCCINT L03P_1

I/O

VCCAUX

L14N_1 A0

L09N_3 LHCLK3 IRDY2

I/O



L16N_1

INPUT

 I/O

I/O

L11P_3 LHCLK6

I/O L19P_1 LDC1

VCCO_1

L09P_3 LHCLK2

I/O

I/O L19N_1 LDC2

INPUT

GND

L11N_3 LHCLK7

INPUT

LDC0

I/O

I/O

TMS

I/O

L06P_3

L10N_3 LHCLK5

GND

INPUT

I/O

I/O

TCK

VREF_1

L06N_3

L10P_3 LHCLK4 TRDY2

16

I/O

I/O

I/O

15

L18P_1 HDC

I/O VCCINT L18N_1

L07P_3

I/O

T



I/O

I/O

L13P_3

R

INPUT

10

INPUT

L07N_3

I/O

P

VCCINT

I/O L15N_0

Bank 0 8 9

7

INPUT

L12N_3

N



L18N_0

L16P_0

INPUT

INPUT

I/O

INPUT INPUT PROG_B VCCINT

VCCO_3

VCCAUX

L19P_0

K

M

I/O

6

VREF_3

H INPUT

J

TDI

5

L09N_1 A9 RHCLK1

Bank 1

1

I/O L09P_1 A10 RHCLK0 VCCAUX

I/O VCCO_1

I/O L03N_1 VREF_1



L04N_1 VREF_1

I/O L04P_1

I/O

I/O

I/O

L20P_2 VS0 A17

L02N_1 A13

L02P_1 A14

I/O

I/O

I/O

I/O

L19N_2 VS1 A18

L20N_2 CCLK

L01N_1 A15

L01P_1 A16

INPUT

DONE

GND

I/O L19P_2 VS2 A19

Bank 2 DS312-4_05_101805

Figure 85: FT256 Package Footprint (top view)

2 28 6 

CONFIG: Dedicated configuration pins

4

JTAG: Dedicated JTAG port pins

8

VCCINT: Internal core supply voltage (+1.2V)

GND: Ground

16

VCCO: Output voltage supply for bank

8

VCCAUX: Auxiliary supply voltage (+2.5V)

Migration Difference: For flexible package migration, use these pins as inputs.

18

Unconnected pins on XC3S250E

DS312 (v4.1) July 19, 2013 Product Specification

()

www.xilinx.com 196

Spartan-3E FPGA Family: Pinout Descriptions

FG320: 320-ball Fine-pitch Ball Grid Array The 320-ball fine-pitch ball grid array package, FG320, supports three different Spartan-3E FPGAs, including the XC3S500E, the XC3S1200E, and the XC3S1600E, as shown in Table 148 and Figure 86. The FG320 package is an 18 x 18 array of solder balls minus the four center balls. Table 148 lists all the package pins. They are sorted by bank number and then by pin name of the largest device. Pins that form a differential I/O pair appear together in the table. The table also shows the pin number for each pin and the pin type, as defined earlier. The highlighted rows indicate pinout differences between the XC3S500E, the XC3S1200E, and the XC3S1600E FPGAs. The XC3S500E has 18 unconnected balls, indicated as N.C. (No Connection) in Table 148 and with the black diamond character () in Table 148 and Figure 86.

If the table row is highlighted in tan, then this is an instance where an unconnected pin on the XC3S500E FPGA maps to a VREF pin on the XC3S1200E and XC3S1600E FPGA. If the FPGA application uses an I/O standard that requires a VREF voltage reference, connect the highlighted pin to the VREF voltage supply, even though this does not actually connect to the XC3S500E FPGA. This VREF connection on the board allows future migration to the larger devices without modifying the printed-circuit board. All other balls have nearly identical functionality on all three devices. Table 147 summarizes the Spartan-3E footprint migration differences for the FG320 package. An electronic version of this package pinout table and footprint diagram is available for download from the Xilinx web site at: http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip

Pinout Table Table 148: FG320 Package Pinout Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

0

IP

IO

IO

A7

500E: INPUT 1200E: I/O 1600E: I/O

0

IO

IO

IO

A8

I/O

0

IO

IO

IO

A11

I/O

0

N.C. ()

IO

IO

A12

500E: N.C. 1200E: I/O 1600E: I/O

0

IO

IO

IO

C4

I/O

0

IP

IO

IO

D13

500E: INPUT 1200E: I/O 1600E: I/O

0

IO

IO

IO

E13

I/O

0

IO

IO

IO

G9

I/O

0

IO/VREF_0

IO/VREF_0

IO/VREF_0

B11

VREF

0

IO_L01N_0

IO_L01N_0

IO_L01N_0

A16

I/O

0

IO_L01P_0

IO_L01P_0

IO_L01P_0

B16

I/O

0

IO_L03N_0/VREF_0

IO_L03N_0/VREF_0

IO_L03N_0/VREF_0

C14

VREF

0

IO_L03P_0

IO_L03P_0

IO_L03P_0

D14

I/O

0

IO_L04N_0

IO_L04N_0

IO_L04N_0

A14

I/O

0

IO_L04P_0

IO_L04P_0

IO_L04P_0

B14

I/O

0

IO_L05N_0/VREF_0

IO_L05N_0/VREF_0

IO_L05N_0/VREF_0

B13

VREF

0

IO_L05P_0

IO_L05P_0

IO_L05P_0

A13

I/O

0

IO_L06N_0

IO_L06N_0

IO_L06N_0

E12

I/O

0

IO_L06P_0

IO_L06P_0

IO_L06P_0

F12

I/O

0

IO_L08N_0

IO_L08N_0

IO_L08N_0

F11

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 197

Spartan-3E FPGA Family: Pinout Descriptions Table 148: FG320 Package Pinout (Cont’d) Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

0

IO_L08P_0

IO_L08P_0

IO_L08P_0

E11

I/O

0

IO_L09N_0

IO_L09N_0

IO_L09N_0

D11

I/O

0

IO_L09P_0

IO_L09P_0

IO_L09P_0

C11

I/O

0

IO_L11N_0/GCLK5

IO_L11N_0/GCLK5

IO_L11N_0/GCLK5

E10

GCLK

0

IO_L11P_0/GCLK4

IO_L11P_0/GCLK4

IO_L11P_0/GCLK4

D10

GCLK

0

IO_L12N_0/GCLK7

IO_L12N_0/GCLK7

IO_L12N_0/GCLK7

A10

GCLK

0

IO_L12P_0/GCLK6

IO_L12P_0/GCLK6

IO_L12P_0/GCLK6

B10

GCLK

0

IO_L14N_0/GCLK11

IO_L14N_0/GCLK11

IO_L14N_0/GCLK11

D9

GCLK

0

IO_L14P_0/GCLK10

IO_L14P_0/GCLK10

IO_L14P_0/GCLK10

C9

GCLK

0

IO_L15N_0

IO_L15N_0

IO_L15N_0

F9

I/O

0

IO_L15P_0

IO_L15P_0

IO_L15P_0

E9

I/O

0

IO_L17N_0

IO_L17N_0

IO_L17N_0

F8

I/O

0

IO_L17P_0

IO_L17P_0

IO_L17P_0

E8

I/O

0

IO_L18N_0/VREF_0

IO_L18N_0/VREF_0

IO_L18N_0/VREF_0

D7

VREF

0

IO_L18P_0

IO_L18P_0

IO_L18P_0

C7

I/O

0

IO_L19N_0/VREF_0

IO_L19N_0/VREF_0

IO_L19N_0/VREF_0

E7

VREF

0

IO_L19P_0

IO_L19P_0

IO_L19P_0

F7

I/O

0

IO_L20N_0

IO_L20N_0

IO_L20N_0

A6

I/O

0

IO_L20P_0

IO_L20P_0

IO_L20P_0

B6

I/O

0

N.C. ()

IO_L21N_0

IO_L21N_0

E6

500E: N.C. 1200E: I/O 1600E: I/O

0

N.C. ()

IO_L21P_0

IO_L21P_0

D6

500E: N.C. 1200E: I/O 1600E: I/O

0

IO_L23N_0/VREF_0

IO_L23N_0/VREF_0

IO_L23N_0/VREF_0

D5

VREF

0

IO_L23P_0

IO_L23P_0

IO_L23P_0

C5

I/O

0

IO_L24N_0

IO_L24N_0

IO_L24N_0

B4

I/O

0

IO_L24P_0

IO_L24P_0

IO_L24P_0

A4

I/O

0

IO_L25N_0/HSWAP

IO_L25N_0/HSWAP

IO_L25N_0/HSWAP

B3

DUAL

0

IO_L25P_0

IO_L25P_0

IO_L25P_0

C3

I/O

0

IP

IP

IP

A3

INPUT

0

IP

IP

IP

C15

INPUT

0

IP_L02N_0

IP_L02N_0

IP_L02N_0

A15

INPUT

0

IP_L02P_0

IP_L02P_0

IP_L02P_0

B15

INPUT

0

IP_L07N_0

IP_L07N_0

IP_L07N_0

D12

INPUT

0

IP_L07P_0

IP_L07P_0

IP_L07P_0

C12

INPUT

0

IP_L10N_0

IP_L10N_0

IP_L10N_0

G10

INPUT

0

IP_L10P_0

IP_L10P_0

IP_L10P_0

F10

INPUT

0

IP_L13N_0/GCLK9

IP_L13N_0/GCLK9

IP_L13N_0/GCLK9

B9

GCLK

0

IP_L13P_0/GCLK8

IP_L13P_0/GCLK8

IP_L13P_0/GCLK8

B8

GCLK

0

IP_L16N_0

IP_L16N_0

IP_L16N_0

D8

INPUT

0

IP_L16P_0

IP_L16P_0

IP_L16P_0

C8

INPUT

0

IP_L22N_0

IP_L22N_0

IP_L22N_0

B5

INPUT

0

IP_L22P_0

IP_L22P_0

IP_L22P_0

A5

INPUT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 198

Spartan-3E FPGA Family: Pinout Descriptions Table 148: FG320 Package Pinout (Cont’d) Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

0

VCCO_0

VCCO_0

VCCO_0

A9

VCCO

0

VCCO_0

VCCO_0

VCCO_0

C6

VCCO

0

VCCO_0

VCCO_0

VCCO_0

C13

VCCO

0

VCCO_0

VCCO_0

VCCO_0

G8

VCCO

0

VCCO_0

VCCO_0

VCCO_0

G11

VCCO

1

N.C. ()

IO

IO

P16

500E: N.C. 1200E: I/O 1600E: I/O

1

IO_L01N_1/A15

IO_L01N_1/A15

IO_L01N_1/A15

T17

DUAL

1

IO_L01P_1/A16

IO_L01P_1/A16

IO_L01P_1/A16

U18

DUAL

1

IO_L02N_1/A13

IO_L02N_1/A13

IO_L02N_1/A13

T18

DUAL

1

IO_L02P_1/A14

IO_L02P_1/A14

IO_L02P_1/A14

R18

DUAL

1

IO_L03N_1/VREF_1

IO_L03N_1/VREF_1

IO_L03N_1/VREF_1

R16

VREF

1

IO_L03P_1

IO_L03P_1

IO_L03P_1

R15

I/O

1

N.C. ()

IO_L04N_1

IO_L04N_1

N14

500E: N.C. 1200E: I/O 1600E: I/O

1

N.C. ()

IO_L04P_1

IO_L04P_1

N15

500E: N.C. 1200E: I/O 1600E: I/O

1

IO_L05N_1/VREF_1

IO_L05N_1/VREF_1

IO_L05N_1/VREF_1

M13

VREF

1

IO_L05P_1

IO_L05P_1

IO_L05P_1

M14

I/O

1

IO_L06N_1

IO_L06N_1

IO_L06N_1

P18

I/O

1

IO_L06P_1

IO_L06P_1

IO_L06P_1

P17

I/O

1

IO_L07N_1

IO_L07N_1

IO_L07N_1

M16

I/O

1

IO_L07P_1

IO_L07P_1

IO_L07P_1

M15

I/O

1

IO_L08N_1

IO_L08N_1

IO_L08N_1

M18

I/O

1

IO_L08P_1

IO_L08P_1

IO_L08P_1

N18

I/O

1

IO_L09N_1/A11

IO_L09N_1/A11

IO_L09N_1/A11

L15

DUAL

1

IO_L09P_1/A12

IO_L09P_1/A12

IO_L09P_1/A12

L16

DUAL

1

IO_L10N_1/VREF_1

IO_L10N_1/VREF_1

IO_L10N_1/VREF_1

L17

VREF

1

IO_L10P_1

IO_L10P_1

IO_L10P_1

L18

I/O

1

IO_L11N_1/A9/RHCLK1

IO_L11N_1/A9/RHCLK1

IO_L11N_1/A9/RHCLK1

K12

RHCLK/DUAL

1

IO_L11P_1/A10/RHCLK0

IO_L11P_1/A10/RHCLK0

IO_L11P_1/A10/RHCLK0

K13

RHCLK/DUAL

1

IO_L12N_1/A7/RHCLK3/ TRDY1

IO_L12N_1/A7/RHCLK3/ TRDY1

IO_L12N_1/A7/RHCLK3/ TRDY1

K14

RHCLK/DUAL

1

IO_L12P_1/A8/RHCLK2

IO_L12P_1/A8/RHCLK2

IO_L12P_1/A8/RHCLK2

K15

RHCLK/DUAL

1

IO_L13N_1/A5/RHCLK5

IO_L13N_1/A5/RHCLK5

IO_L13N_1/A5/RHCLK5

J16

RHCLK/DUAL

1

IO_L13P_1/A6/RHCLK4/ IRDY1

IO_L13P_1/A6/RHCLK4/ IRDY1

IO_L13P_1/A6/RHCLK4/ IRDY1

J17

RHCLK/DUAL

1

IO_L14N_1/A3/RHCLK7

IO_L14N_1/A3/RHCLK7

IO_L14N_1/A3/RHCLK7

J14

RHCLK/DUAL

1

IO_L14P_1/A4/RHCLK6

IO_L14P_1/A4/RHCLK6

IO_L14P_1/A4/RHCLK6

J15

RHCLK/DUAL

1

IO_L15N_1/A1

IO_L15N_1/A1

IO_L15N_1/A1

J13

DUAL

1

IO_L15P_1/A2

IO_L15P_1/A2

IO_L15P_1/A2

J12

DUAL

1

IO_L16N_1/A0

IO_L16N_1/A0

IO_L16N_1/A0

H17

DUAL

1

IO_L16P_1

IO_L16P_1

IO_L16P_1

H16

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 199

Spartan-3E FPGA Family: Pinout Descriptions Table 148: FG320 Package Pinout (Cont’d) Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

1

IO_L17N_1

IO_L17N_1

IO_L17N_1

H15

I/O

1

IO_L17P_1

IO_L17P_1

IO_L17P_1

H14

I/O

1

IO_L18N_1

IO_L18N_1

IO_L18N_1

G16

I/O

1

IO_L18P_1

IO_L18P_1

IO_L18P_1

G15

I/O

1

IO_L19N_1

IO_L19N_1

IO_L19N_1

F17

I/O

1

IO_L19P_1

IO_L19P_1

IO_L19P_1

F18

I/O

1

IO_L20N_1

IO_L20N_1

IO_L20N_1

G13

I/O

1

IO_L20P_1

IO_L20P_1

IO_L20P_1

G14

I/O

1

IO_L21N_1

IO_L21N_1

IO_L21N_1

F14

I/O

1

IO_L21P_1

IO_L21P_1

IO_L21P_1

F15

I/O

1

N.C. ()

IO_L22N_1

IO_L22N_1

E16

500E: N.C. 1200E: I/O 1600E: I/O

1

N.C. ()

IO_L22P_1

IO_L22P_1

E15

500E: N.C. 1200E: I/O 1600E: I/O

1

IO_L23N_1/LDC0

IO_L23N_1/LDC0

IO_L23N_1/LDC0

D16

DUAL

1

IO_L23P_1/HDC

IO_L23P_1/HDC

IO_L23P_1/HDC

D17

DUAL

1

IO_L24N_1/LDC2

IO_L24N_1/LDC2

IO_L24N_1/LDC2

C17

DUAL

1

IO_L24P_1/LDC1

IO_L24P_1/LDC1

IO_L24P_1/LDC1

C18

DUAL

1

IP

IP

IP

B18

INPUT

1

IO

IP

IP

E17

500E: I/O 1200E: INPUT 1600E: INPUT

1

IP

IP

IP

E18

INPUT

1

IP

IP

IP

G18

INPUT

1

IP

IP

IP

H13

INPUT

1

IP

IP

IP

K17

INPUT

1

IP

IP

IP

K18

INPUT

1

IP

IP

IP

L13

INPUT

1

IP

IP

IP

L14

INPUT

1

IP

IP

IP

N17

INPUT

1

IO

IP

IP

P15

500E: I/O 1200E: INPUT 1600E: INPUT

1

IP

IP

IP

R17

INPUT

1

IP/VREF_1

IP/VREF_1

IP/VREF_1

D18

VREF

1

IP/VREF_1

IP/VREF_1

IP/VREF_1

H18

VREF

1

VCCO_1

VCCO_1

VCCO_1

F16

VCCO

1

VCCO_1

VCCO_1

VCCO_1

H12

VCCO

1

VCCO_1

VCCO_1

VCCO_1

J18

VCCO

1

VCCO_1

VCCO_1

VCCO_1

L12

VCCO

1

VCCO_1

VCCO_1

VCCO_1

N16

VCCO

2

IO

IO

IO

P9

I/O

2

IO

IO

IO

R11

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 200

Spartan-3E FPGA Family: Pinout Descriptions Table 148: FG320 Package Pinout (Cont’d) Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

2

IP

IO

IO

U6

500E: INPUT 1200E: I/O 1600E: I/O

2

IP

IO

IO

U13

500E: INPUT 1200E: I/O 1600E: I/O

2

N.C. ()

IO

IO

V7

500E: N.C. 1200E: I/O 1600E: I/O

2

IO/D5

IO/D5

IO/D5

R9

DUAL

2

IO/M1

IO/M1

IO/M1

V11

DUAL

2

IO/VREF_2

IO/VREF_2

IO/VREF_2

T15

VREF

2

IO/VREF_2

IO/VREF_2

IO/VREF_2

U5

VREF

2

IO_L01N_2/INIT_B

IO_L01N_2/INIT_B

IO_L01N_2/INIT_B

T3

DUAL

2

IO_L01P_2/CSO_B

IO_L01P_2/CSO_B

IO_L01P_2/CSO_B

U3

DUAL

2

IO_L03N_2/MOSI/CSI_B

IO_L03N_2/MOSI/CSI_B

IO_L03N_2/MOSI/CSI_B

T4

DUAL

2

IO_L03P_2/DOUT/BUSY

IO_L03P_2/DOUT/BUSY

IO_L03P_2/DOUT/BUSY

U4

DUAL

2

IO_L04N_2

IO_L04N_2

IO_L04N_2

T5

I/O

2

IO_L04P_2

IO_L04P_2

IO_L04P_2

R5

I/O

2

IO_L05N_2

IO_L05N_2

IO_L05N_2

P6

I/O

2

IO_L05P_2

IO_L05P_2

IO_L05P_2

R6

I/O

2

N.C. ()

IO_L06N_2/VREF_2

IO_L06N_2/VREF_2

V6

500E: N.C. 1200E: VREF 1600E: VREF

2

N.C. ()

IO_L06P_2

IO_L06P_2

V5

500E: N.C. 1200E: I/O 1600E: I/O

2

IO_L07N_2

IO_L07N_2

IO_L07N_2

P7

I/O

2

IO_L07P_2

IO_L07P_2

IO_L07P_2

N7

I/O

2

IO_L09N_2

IO_L09N_2

IO_L09N_2

N8

I/O

2

IO_L09P_2

IO_L09P_2

IO_L09P_2

P8

I/O

2

IO_L10N_2

IO_L10N_2

IO_L10N_2

T8

I/O

2

IO_L10P_2

IO_L10P_2

IO_L10P_2

R8

I/O

2

IO_L12N_2/D6/GCLK13

IO_L12N_2/D6/GCLK13

IO_L12N_2/D6/GCLK13

M9

DUAL/GCLK

2

IO_L12P_2/D7/GCLK12

IO_L12P_2/D7/GCLK12

IO_L12P_2/D7/GCLK12

N9

DUAL/GCLK

2

IO_L13N_2/D3/GCLK15

IO_L13N_2/D3/GCLK15

IO_L13N_2/D3/GCLK15

V9

DUAL/GCLK

2

IO_L13P_2/D4/GCLK14

IO_L13P_2/D4/GCLK14

IO_L13P_2/D4/GCLK14

U9

DUAL/GCLK

2

IO_L15N_2/D1/GCLK3

IO_L15N_2/D1/GCLK3

IO_L15N_2/D1/GCLK3

P10

DUAL/GCLK

2

IO_L15P_2/D2/GCLK2

IO_L15P_2/D2/GCLK2

IO_L15P_2/D2/GCLK2

R10

DUAL/GCLK

2

IO_L16N_2/DIN/D0

IO_L16N_2/DIN/D0

IO_L16N_2/DIN/D0

N10

DUAL

2

IO_L16P_2/M0

IO_L16P_2/M0

IO_L16P_2/M0

M10

DUAL

2

IO_L18N_2

IO_L18N_2

IO_L18N_2

N11

I/O

2

IO_L18P_2

IO_L18P_2

IO_L18P_2

P11

I/O

2

IO_L19N_2/VREF_2

IO_L19N_2/VREF_2

IO_L19N_2/VREF_2

V13

VREF

2

IO_L19P_2

IO_L19P_2

IO_L19P_2

V12

I/O

2

IO_L20N_2

IO_L20N_2

IO_L20N_2

R12

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 201

Spartan-3E FPGA Family: Pinout Descriptions Table 148: FG320 Package Pinout (Cont’d) Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

2

IO_L20P_2

IO_L20P_2

IO_L20P_2

T12

I/O

2

N.C. ()

IO_L21N_2

IO_L21N_2

P12

500E: N.C. 1200E: I/O 1600E: I/O

2

N.C. ()

IO_L21P_2

IO_L21P_2

N12

500E: N.C. 1200E: I/O 1600E: I/O

2

IO_L22N_2/A22

IO_L22N_2/A22

IO_L22N_2/A22

R13

DUAL

2

IO_L22P_2/A23

IO_L22P_2/A23

IO_L22P_2/A23

P13

DUAL

2

IO_L24N_2/A20

IO_L24N_2/A20

IO_L24N_2/A20

R14

DUAL

2

IO_L24P_2/A21

IO_L24P_2/A21

IO_L24P_2/A21

T14

DUAL

2

IO_L25N_2/VS1/A18

IO_L25N_2/VS1/A18

IO_L25N_2/VS1/A18

U15

DUAL

2

IO_L25P_2/VS2/A19

IO_L25P_2/VS2/A19

IO_L25P_2/VS2/A19

V15

DUAL

2

IO_L26N_2/CCLK

IO_L26N_2/CCLK

IO_L26N_2/CCLK

U16

DUAL

2

IO_L26P_2/VS0/A17

IO_L26P_2/VS0/A17

IO_L26P_2/VS0/A17

T16

DUAL

2

IP

IP

IP

V2

INPUT

2

IP

IP

IP

V16

INPUT

2

IP_L02N_2

IP_L02N_2

IP_L02N_2

V3

INPUT

2

IP_L02P_2

IP_L02P_2

IP_L02P_2

V4

INPUT

2

IP_L08N_2

IP_L08N_2

IP_L08N_2

R7

INPUT

2

IP_L08P_2

IP_L08P_2

IP_L08P_2

T7

INPUT

2

IP_L11N_2/VREF_2

IP_L11N_2/VREF_2

IP_L11N_2/VREF_2

V8

VREF

2

IP_L11P_2

IP_L11P_2

IP_L11P_2

U8

INPUT

2

IP_L14N_2/M2/GCLK1

IP_L14N_2/M2/GCLK1

IP_L14N_2/M2/GCLK1

T10

DUAL/GCLK

2

IP_L14P_2/RDWR_B/ GCLK0

IP_L14P_2/RDWR_B/ GCLK0

IP_L14P_2/RDWR_B/ GCLK0

U10

DUAL/GCLK

2

IP_L17N_2

IP_L17N_2

IP_L17N_2

U11

INPUT

2

IP_L17P_2

IP_L17P_2

IP_L17P_2

T11

INPUT

2

IP_L23N_2

IP_L23N_2

IP_L23N_2

U14

INPUT

2

IP_L23P_2

IP_L23P_2

IP_L23P_2

V14

INPUT

2

VCCO_2

VCCO_2

VCCO_2

M8

VCCO

2

VCCO_2

VCCO_2

VCCO_2

M11

VCCO

2

VCCO_2

VCCO_2

VCCO_2

T6

VCCO

2

VCCO_2

VCCO_2

VCCO_2

T13

VCCO

2

VCCO_2

VCCO_2

VCCO_2

V10

VCCO

3

N.C. ()

IO

IO

D4

500E: N.C. 1200E: I/O 1600E: I/O

3

IO_L01N_3

IO_L01N_3

IO_L01N_3

C2

I/O

3

IO_L01P_3

IO_L01P_3

IO_L01P_3

C1

I/O

3

IO_L02N_3/VREF_3

IO_L02N_3/VREF_3

IO_L02N_3/VREF_3

D2

VREF

3

IO_L02P_3

IO_L02P_3

IO_L02P_3

D1

I/O

3

IO_L03N_3

IO_L03N_3

IO_L03N_3

E1

I/O

3

IO_L03P_3

IO_L03P_3

IO_L03P_3

E2

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 202

Spartan-3E FPGA Family: Pinout Descriptions Table 148: FG320 Package Pinout (Cont’d) Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

3

N.C. ()

IO_L04N_3

IO_L04N_3

E3

500E: N.C. 1200E: I/O 1600E: I/O

3

N.C. ()

IO_L04P_3

IO_L04P_3

E4

500E: N.C. 1200E: I/O 1600E: I/O

3

IO_L05N_3

IO_L05N_3

IO_L05N_3

F2

I/O

3

IO_L05P_3

IO_L05P_3

IO_L05P_3

F1

I/O

3

IO_L06N_3/VREF_3

IO_L06N_3/VREF_3

IO_L06N_3/VREF_3

G4

VREF

3

IO_L06P_3

IO_L06P_3

IO_L06P_3

G3

I/O

3

IO_L07N_3

IO_L07N_3

IO_L07N_3

G5

I/O

3

IO_L07P_3

IO_L07P_3

IO_L07P_3

G6

I/O

3

IO_L08N_3

IO_L08N_3

IO_L08N_3

H5

I/O

3

IO_L08P_3

IO_L08P_3

IO_L08P_3

H6

I/O

3

IO_L09N_3

IO_L09N_3

IO_L09N_3

H3

I/O

3

IO_L09P_3

IO_L09P_3

IO_L09P_3

H4

I/O

3

IO_L10N_3

IO_L10N_3

IO_L10N_3

H1

I/O

3

IO_L10P_3

IO_L10P_3

IO_L10P_3

H2

I/O

3

IO_L11N_3/LHCLK1

IO_L11N_3/LHCLK1

IO_L11N_3/LHCLK1

J4

LHCLK

3

IO_L11P_3/LHCLK0

IO_L11P_3/LHCLK0

IO_L11P_3/LHCLK0

J5

LHCLK

3

IO_L12N_3/LHCLK3/ IRDY2

IO_L12N_3/LHCLK3/ IRDY2

IO_L12N_3/LHCLK3/ IRDY2

J2

LHCLK

3

IO_L12P_3/LHCLK2

IO_L12P_3/LHCLK2

IO_L12P_3/LHCLK2

J1

LHCLK

3

IO_L13N_3/LHCLK5

IO_L13N_3/LHCLK5

IO_L13N_3/LHCLK5

K4

LHCLK

3

IO_L13P_3/LHCLK4/ TRDY2

IO_L13P_3/LHCLK4/ TRDY2

IO_L13P_3/LHCLK4/ TRDY2

K3

LHCLK

3

IO_L14N_3/LHCLK7

IO_L14N_3/LHCLK7

IO_L14N_3/LHCLK7

K5

LHCLK

3

IO_L14P_3/LHCLK6

IO_L14P_3/LHCLK6

IO_L14P_3/LHCLK6

K6

LHCLK

3

IO_L15N_3

IO_L15N_3

IO_L15N_3

L2

I/O

3

IO_L15P_3

IO_L15P_3

IO_L15P_3

L1

I/O

3

IO_L16N_3

IO_L16N_3

IO_L16N_3

L4

I/O

3

IO_L16P_3

IO_L16P_3

IO_L16P_3

L3

I/O

3

IO_L17N_3/VREF_3

IO_L17N_3/VREF_3

IO_L17N_3/VREF_3

L5

VREF

3

IO_L17P_3

IO_L17P_3

IO_L17P_3

L6

I/O

3

IO_L18N_3

IO_L18N_3

IO_L18N_3

M3

I/O

3

IO_L18P_3

IO_L18P_3

IO_L18P_3

M4

I/O

3

IO_L19N_3

IO_L19N_3

IO_L19N_3

M6

I/O

3

IO_L19P_3

IO_L19P_3

IO_L19P_3

M5

I/O

3

IO_L20N_3

IO_L20N_3

IO_L20N_3

N5

I/O

3

IO_L20P_3

IO_L20P_3

IO_L20P_3

N4

I/O

3

IO_L21N_3

IO_L21N_3

IO_L21N_3

P1

I/O

3

IO_L21P_3

IO_L21P_3

IO_L21P_3

P2

I/O

3

N.C. ()

IO_L22N_3

IO_L22N_3

P4

500E: N.C. 1200E: I/O 1600E: I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 203

Spartan-3E FPGA Family: Pinout Descriptions Table 148: FG320 Package Pinout (Cont’d) Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

3

N.C. ()

IO_L22P_3

IO_L22P_3

P3

500E: N.C. 1200E: I/O 1600E: I/O

3

IO_L23N_3

IO_L23N_3

IO_L23N_3

R2

I/O

3

IO_L23P_3

IO_L23P_3

IO_L23P_3

R3

I/O

3

IO_L24N_3

IO_L24N_3

IO_L24N_3

T1

I/O

3

IO_L24P_3

IO_L24P_3

IO_L24P_3

T2

I/O

3

IP

IP

IP

D3

INPUT

3

IO

IP

IP

F4

500E: I/O 1200E: INPUT 1600E: INPUT

3

IP

IP

IP

F5

INPUT

3

IP

IP

IP

G1

INPUT

3

IP

IP

IP

J7

INPUT

3

IP

IP

IP

K2

INPUT

3

IP

IP

IP

K7

INPUT

3

IP

IP

IP

M1

INPUT

3

IP

IP

IP

N1

INPUT

3

IP

IP

IP

N2

INPUT

3

IP

IP

IP

R1

INPUT

3

IP

IP

IP

U1

INPUT

3

IP/VREF_3

IP/VREF_3

IP/VREF_3

J6

VREF

3

IO/VREF_3

IP/VREF_3

IP/VREF_3

R4

500E: VREF(I/O) 1200E: VREF(INPUT) 1600E: VREF(INPUT)

3

VCCO_3

VCCO_3

VCCO_3

F3

VCCO

3

VCCO_3

VCCO_3

VCCO_3

H7

VCCO

3

VCCO_3

VCCO_3

VCCO_3

K1

VCCO

3

VCCO_3

VCCO_3

VCCO_3

L7

VCCO

3

VCCO_3

VCCO_3

VCCO_3

N3

VCCO

GND

GND

GND

GND

A1

GND

GND

GND

GND

GND

A18

GND

GND

GND

GND

GND

B2

GND

GND

GND

GND

GND

B17

GND

GND

GND

GND

GND

C10

GND

GND

GND

GND

GND

G7

GND

GND

GND

GND

GND

G12

GND

GND

GND

GND

GND

H8

GND

GND

GND

GND

GND

H9

GND

GND

GND

GND

GND

H10

GND

GND

GND

GND

GND

H11

GND

GND

GND

GND

GND

J3

GND

GND

GND

GND

GND

J8

GND

GND

GND

GND

GND

J11

GND

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 204

Spartan-3E FPGA Family: Pinout Descriptions Table 148: FG320 Package Pinout (Cont’d) Bank

XC3S500E Pin Name

XC3S1200E Pin Name

XC3S1600E Pin Name

FG320 Ball

Type

GND

GND

GND

GND

K8

GND

GND

GND

GND

GND

K11

GND

GND

GND

GND

GND

K16

GND

GND

GND

GND

GND

L8

GND

GND

GND

GND

GND

L9

GND

GND

GND

GND

GND

L10

GND

GND

GND

GND

GND

L11

GND

GND

GND

GND

GND

M7

GND

GND

GND

GND

GND

M12

GND

GND

GND

GND

GND

T9

GND

GND

GND

GND

GND

U2

GND

GND

GND

GND

GND

U17

GND

GND

GND

GND

GND

V1

GND

GND

GND

GND

GND

V18

GND

VCCAUX

DONE

DONE

DONE

V17

CONFIG

VCCAUX

PROG_B

PROG_B

PROG_B

B1

CONFIG

VCCAUX

TCK

TCK

TCK

A17

JTAG

VCCAUX

TDI

TDI

TDI

A2

JTAG

VCCAUX

TDO

TDO

TDO

C16

JTAG

VCCAUX

TMS

TMS

TMS

D15

JTAG

VCCAUX

VCCAUX

VCCAUX

VCCAUX

B7

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

B12

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

G2

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

G17

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

M2

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

M17

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

U7

VCCAUX

VCCAUX

VCCAUX

VCCAUX

VCCAUX

U12

VCCAUX

VCCINT

VCCINT

VCCINT

VCCINT

E5

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

E14

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

F6

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

F13

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

N6

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

N13

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

P5

VCCINT

VCCINT

VCCINT

VCCINT

VCCINT

P14

VCCINT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 205

Spartan-3E FPGA Family: Pinout Descriptions

User I/Os by Bank Table 149 and Table 150 indicate how the available user-I/O pins are distributed between the four I/O banks on the FG320 package. Table 149: User I/Os Per Bank for XC3S500E in the FG320 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

58

29

14

1

6

8

1

58

22

10

21

5

0(2)

Bottom

2

58

17

13

24

4

0(2)

Left

3

58

34

11

0

5

8

232

102

48

46

20

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

Table 150: User I/Os Per Bank for XC3S1200E and XC3S1600E in the FG320 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

61

34

12

1

6

8

1

63

25

12

21

5

0(2)

Bottom

2

63

23

11

24

5

0(2)

Left

3

63

38

12

0

5

8

250

120

47

46

21

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 206

Spartan-3E FPGA Family: Pinout Descriptions

Footprint Migration Differences Table 151 summarizes any footprint and functionality differences between the XC3S500E, the XC3S1200E, and the XC3S1600E FPGAs that may affect easy migration between devices available in the FG320 package. There are 26 such balls. All other pins not listed in Table 151 unconditionally migrate between Spartan-3E devices available in the FG320 package. The XC3S500E is duplicated on both the left and right sides of the table to show migrations to and from the XC3S1200E

and the XC3S1600E. The arrows indicate the direction for easy migration. A double-ended arrow () indicates that the two pins have identical functionality. A left-facing arrow () indicates that the pin on the device on the right unconditionally migrates to the pin on the device on the left. It may be possible to migrate the opposite direction depending on the I/O configuration. For example, an I/O pin (Type = I/O) can migrate to an input-only pin (Type = INPUT) if the I/O pin is configured as an input.

Table 151: FG320 Footprint Migration Differences Pin

Bank

XC3S500E

Migration

XC3S1200E

Migration

XC3S1600E

Migration

XC3S500E

A7

0

INPUT



I/O



I/O



INPUT

A12

0

N.C.



I/O



I/O



N.C.

D4

3

N.C.



I/O



I/O



N.C.

D6

0

N.C.



I/O



I/O



N.C.

D13

0

INPUT



I/O



I/O



INPUT

E3

3

N.C.



I/O



I/O



N.C.

E4

3

N.C.



I/O



I/O



N.C.

E6

0

N.C.



I/O



I/O



N.C.

E15

1

N.C.



I/O



I/O



N.C.

E16

1

N.C.



I/O



I/O



N.C.

E17

1

I/O



INPUT



INPUT



I/O

F4

3

I/O



INPUT



INPUT



I/O

N12

2

N.C.



I/O



I/O



N.C.

N14

1

N.C.



I/O



I/O



N.C.

N15

1

N.C.



I/O



I/O



N.C.

P3

3

N.C.



I/O



I/O



N.C.

P4

3

N.C.



I/O



I/O



N.C.

P12

2

N.C.



I/O



I/O



N.C.

P15

1

I/O



INPUT



INPUT



I/O

P16

1

N.C.



I/O



I/O



N.C.

R4

3

VREF(I/O)



VREF(INPUT)



VREF(INPUT)



VREF(I/O)

U6

2

INPUT



I/O



I/O



INPUT

U13

2

INPUT



I/O



I/O



INPUT

V5

2

N.C.



I/O



I/O



N.C.

V6

2

N.C.



VREF



VREF



N.C.

2

N.C.



I/O



I/O



N.C.

V7

DIFFERENCES

26

0

26

Legend: 

This pin is identical on the device on the left and the right.



This pin can unconditionally migrate from the device on the left to the device on the right. Migration in the other direction may be possible depending on how the pin is configured for the device on the right.



This pin can unconditionally migrate from the device on the right to the device on the left. Migration in the other direction may be possible depending on how the pin is configured for the device on the left.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 207

Spartan-3E FPGA Family: Pinout Descriptions

FG320 Footprint X-Ref Target - Figure 86

Bank 0 2

3

A

GND

TDI

INPUT

B

PROG_B

GND

L25N_0 HSWAP

I/O

C

D

E

F

G

Bank 3

H

I/O

I/O

I/O

L01P_3

L01N_3

L25P_0

I/O L02P_3

I/O L02N_3 VREF_3

I/O

I/O

L03N_3

L03P_3

I/O

I/O

L05P_3

L05N_3

INPUT

VCCAUX

INPUT

4

5

6

7

I/O

INPUT

I/O

INPUT

L24P_0

L22P_0

L20N_0

I/O

INPUT

I/O

L24N_0

L22N_0

L20P_0

I/O

INPUT

 I/O L06N_3 VREF_3

I/O

I/O

L07N_3

L07P_3

I/O

I/O

I/O

I/O

I/O

I/O

L10P_3

L09N_3

L09P_3

L08N_3

L08P_3

I/O

I/O

L11N_3 LHCLK1

L11P_3 LHCLK0

I/O

I/O L12N_3 LHCLK3 IRDY2

GND I/O

I/O

I/O

I/O

K

VCCO_3

INPUT

L13P_3 LHCLK4 TRDY2

L13N_3 LHCLK5

L14N_3 LHCLK7

L14P_3 LHCLK6

I/O

I/O

I/O

I/O

L15P_3

L15N_3

L16P_3

L16N_3

I/O

I/O

I/O

L18P_3

L19P_3

L19N_3

N

INPUT

VCCO_3

I/O

I/O

I/O

I/O

L21N_3

L21P_3

L22P_3

L22N_3





I/O

I/O

L23N_3

L23P_3

VREF_3

INPUT

I/O

I/O

L24N_3

L24P_3

U

INPUT

GND

V

GND

INPUT

T

I/O L17P_3

I/O

I/O

L20P_3

L20N_3

INPUT



I/O

I/O

L01N_2 INIT_B

L03N_2 MOSI CSI_B

I/O

I/O

L01P_2 CSO_B

L03P_2 DOUT BUSY

INPUT

INPUT

L02N_2

L02P_2

I/O

I/O

I/O

L14N_0 GCLK11

L11P_0 GCLK4

I/O L15P_0

L11N_0 GCLK5

I/O

INPUT

I/O

L04P_0

L02P_0

L01P_0

INPUT

TDO I/O

I/O

TMS

L23N_1 LDC0

L23P_1 HDC

I/O

INPUT

L09N_0

L07N_0

I/O

I/O

L08P_0

L06N_0

I/O VCCO_0

INPUT

 I/O

L03N_0 VREF_0

I/O L03P_0

I/O VCCINT L22P_1



I/O L24P_1 LDC1

INPUT



I/O

VCCO_0

GND

VCCO_3

GND

GND

GND

VCCO_1

I/O

I/O

I/O

I/O

I/O

INPUT

GND

GND

L15P_1 A2

L15N_1 A1

L14N_1 A3 RHCLK7

L14P_1 A4 4 RHCLK6

L13N_1 A5 RHCLK5

L13P_1 A6 RHCLK4 IRDY1

I/O

I/O

INPUT

GND

GND

L11N_1 A9 RHCLK1

L11P_1 A10 RHCLK0

L12N_1 A7 RHCLK3 TRDY1

GND

INPUT

VCCO_3

GND

GND

GND

VCCO_1

INPUT

INPUT

I/O

I/O

GND

VCCO_2

L12N_2 D6 GCLK13

L16P_2 M0

VCCO_2

GND

L05N_1 VREF_1

I/O

L21P_2

I/O

I/O

L07P_2

L09N_2

I/O L16N_2 DIN D0

I/O

L15N_2 D1 GCLK3

I/O D5

I/O

L08P_2

L10N_2



INPUT L11P_2

I/O

L14N_2 M2 GCLK1

GND I/O

INPUT

L13P_2 D4 GCLK14

L14P_2 RDWR_B GCLK0

INPUT

I/O

L11N_2 VREF_2

L13N_2 D3 GCLK15

I/O L18P_2

L15P_2 D2 GCLK2

INPUT

INPUT

I/O

L18N_2

I/O

I/O



I/O

I/O

I/O

I/O

L20P_1

L18P_1

L18N_1

INPUT

I/O

L17P_2

L20P_2

INPUT L17N_2

VCCO_2

VCCAUX

I/O

I/O

M1

L19P_2

I/O

I/O L24N_2 A20

VCCO_2

L24P_2 A21

INPUT

INPUT

I/O

 I/O L19N_2 VREF_2

L23N_2

INPUT L23P_2

VCCAUX

INPUT

I/O L16N_1 A0

INPUT VREF_1

I/O

I/O

I/O L10N_1 VREF_1

L04P_1

I/O

I/O L19P_1

L09P_1 A12

I/O VCCINT L04N_1

L22N_2 A22

I/O

I/O

I/O

VCCINT

INPUT

L19N_1

L09N_1 A11

L07N_1



INPUT VREF_1

VCCO_1

I/O L12P_1 A8 RHCLK2

I/O

I/O

INPUT

I/O L16P_1

L07P_1

L22P_2 A23

I/O

I/O L17N_1

I/O

I/O

L20N_2

I/O L17P_1

L05P_1

L21N_2



VCCO_1

L20N_1

I/O

I/O

I/O



GND

I/O

L10P_2

VCCAUX

GND

L12P_2 D7 GCLK12

L08N_2

VCCO_2

L10N_0

I/O L21P_1

I/O L24N_1 LDC2

VCCO_0

INPUT

I/O



INPUT

GND

VCCINT

L21N_1

I/O L22N_1

GND

I/O

INPUT



L05N_0 VREF_0

L07P_0

GND

L06P_0

I/O

I/O

VCCAUX

INPUT

TCK

I/O

L05P_2

L06N_2 VREF_2

L01N_0

L08N_0

I/O

I/O

L02N_0

L10P_0

L04P_2

L06P_2

L04N_0

I/O

18

INPUT

I/O



L05P_0

I/O

17

I/O

VCCINT

INPUT



I/O

L15N_0

L09P_2

I/O

16

INPUT

I/O

I/O

VREF_2

15

I/O

L17N_0

L07N_2

I/O

14

I/O

L09P_0

I/O

I/O L17P_0

I/O

L04N_2

GND

L14P_0 GCLK10

L05N_2

VCCINT

I/O VREF_0

13

I/O

I/O

INPUT

I/O

VCCAUX

L16N_0

I/O

12

L19P_0

VREF_3

L18N_3

M INPUT

R

I/O L17N_3 VREF_3

INPUT

I/O

INPUT VCCINT

L12P_3 LHCLK2

P

L16P_0

L19N_0 VREF_0



L10N_3

INPUT

INPUT

I/O VCCINT L21N_0

J

L

I/O L18P_0

I/O



I/O

L12P_0 GCLK6

L18N_0 VREF_0

I/O

L06P_3

I/O

L13N_0 GCLK9

I/O

11

L12N_0 GCLK7

INPUT

L21P_0

L04P_3

VCCO_0

L13P_0 GCLK8

I/O



I/O INPUT

L23N_0 VREF_0

I/O

10

VCCAUX

VCCO_0



9

I/O





I/O

L04N_3

VCCO_3

I/O L23P_0

8

VCCAUX

I/O VCCO_1

 INPUT

I/O





I/O L03P_1

I/O VREF_2

INPUT

I/O L10P_1

I/O L08N_1

I/O L08P_1

I/O

I/O

L06P_1

L06N_1

INPUT

L02P_1 A14

I/O L03N_1 VREF_1

INPUT

Bank 1

1

I/O

I/O

I/O

I/O

L26P_2 VS0 A17

L01N_1 A15

L02N_1 A13

I/O

I/O

L25N_2 VS1 A18

L26N_2 CCLK

GND

L01P_1 A16

INPUT

DONE

GND

I/O

I/O L25P_2 VS2 A19

Bank 2 DS312-4_06_022106

Figure 86: FG320 Package Footprint (top view)

102120 4748 2 18

I/O: Unrestricted, general-purpose user I/O

46

DUAL: Configuration pin, then possible user-I/O

2021

VREF: User I/O or input voltage reference for bank

INPUT: Unrestricted, general-purpose input pin

16

CLK: User I/O, input, or global buffer input

20

VCCO: Output voltage supply for bank

CONFIG: Dedicated configuration pins N.C.: Not connected. Only the XC3S500E has these pins ().

DS312 (v4.1) July 19, 2013 Product Specification

4 28

JTAG: Dedicated JTAG port pins

8

VCCINT: Internal core supply voltage (+1.2V)

GND: Ground

8

VCCAUX: Auxiliary supply voltage (+2.5V)

www.xilinx.com 208

Spartan-3E FPGA Family: Pinout Descriptions

FG400: 400-ball Fine-pitch Ball Grid Array The 400-ball fine-pitch ball grid array, FG400, supports two different Spartan-3E FPGAs, including the XC3S1200E and the XC3S1600E. Both devices share a common footprint for this package as shown in Table 152 and Figure 87.

Table 152: FG400 Package Pinout (Cont’d) XC3S1200E XC3S1600E Pin Name

Bank

FG400 Ball

Type I/O

Table 152 lists all the FG400 package pins. They are sorted by bank number and then by pin name. Pairs of pins that form a differential I/O pair appear together in the table. The table also shows the pin number for each pin and the pin type, as defined earlier.

0

IO_L12P_0

D12

0

IO_L13N_0

E12

I/O

0

IO_L13P_0

F12

I/O

0

IO_L15N_0/GCLK5

G11

GCLK

0

IO_L15P_0/GCLK4

F11

GCLK

An electronic version of this package pinout table and footprint diagram is available for download from the Xilinx website at:

0

IO_L16N_0/GCLK7

E10

GCLK

0

IO_L16P_0/GCLK6

E11

GCLK

0

IO_L18N_0/GCLK11

A9

GCLK

http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip

0

IO_L18P_0/GCLK10

A10

GCLK

0

IO_L19N_0

F9

I/O

Pinout Table

0

IO_L19P_0

E9

I/O

0

IO_L21N_0

C9

I/O

0

IO_L21P_0

D9

I/O

0

IO_L22N_0/VREF_0

B8

VREF

0

IO_L22P_0

B9

I/O

Table 152: FG400 Package Pinout XC3S1200E XC3S1600E Pin Name

Bank 0

IO

FG400 Ball

Type

A3

I/O

0

IO_L24N_0/VREF_0

F7

VREF

IO_L24P_0

F8

I/O

0

IO

A8

I/O

0

0

IO

A12

I/O

0

IO_L25N_0

A6

I/O

IO_L25P_0

A7

I/O

B5

I/O

0

IO

C7

I/O

0

0

IO

C10

I/O

0

IO_L27N_0

0

IO

E8

I/O

0

IO_L27P_0

B6

I/O

IO_L28N_0

D6

I/O

0

IO

E13

I/O

0

0

IO

E16

I/O

0

IO_L28P_0

C6

I/O

0

IO

F13

I/O

0

IO_L30N_0/VREF_0

C5

VREF

IO_L30P_0

D5

I/O

0

IO

F14

I/O

0

0

IO

G7

I/O

0

IO_L31N_0

A2

I/O

IO_L31P_0

B2

I/O

D4

DUAL

0

IO/VREF_0

C11

VREF

0

0

IO_L01N_0

B17

I/O

0

IO_L32N_0/HSWAP

0

IO_L01P_0

C17

I/O

0

IO_L32P_0

C4

I/O

IP

B18

INPUT

E5

INPUT

0

IO_L03N_0/VREF_0

A18

VREF

0

0

IO_L03P_0

A19

I/O

0

IP

0

IO_L04N_0

A17

I/O

0

IP_L02N_0

C16

INPUT

IP_L02P_0

D16

INPUT

0

IO_L04P_0

A16

I/O

0

0

IO_L06N_0

A15

I/O

0

IP_L05N_0

D15

INPUT

IP_L05P_0

C15

INPUT

E14

INPUT

0

IO_L06P_0

B15

I/O

0

0

IO_L07N_0

C14

I/O

0

IP_L08N_0

0

IO_L07P_0

D14

I/O

0

IP_L08P_0

E15

INPUT

IP_L11N_0

G14

INPUT

G13

INPUT

0

IO_L09N_0/VREF_0

A13

VREF

0

0

IO_L09P_0

A14

I/O

0

IP_L11P_0

0

IO_L10N_0

B13

I/O

0

IP_L14N_0

B11

INPUT

IP_L14P_0

B12

INPUT

IP_L17N_0/GCLK9

G10

GCLK

0

IO_L10P_0

C13

I/O

0

0

IO_L12N_0

C12

I/O

0

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 209

Spartan-3E FPGA Family: Pinout Descriptions Table 152: FG400 Package Pinout (Cont’d) Bank

XC3S1200E XC3S1600E Pin Name

FG400 Ball

Table 152: FG400 Package Pinout (Cont’d) XC3S1200E XC3S1600E Pin Name

FG400 Ball

Type

Bank 1

IO_L14P_1/A10/RHCLK0

M16

RHCLK/ DUAL

1

IO_L15N_1/A7/RHCLK3/ TRDY1

L14

RHCLK/ DUAL

1

IO_L15P_1/A8/RHCLK2

L15

RHCLK/ DUAL

1

IO_L16N_1/A5/RHCLK5

K14

RHCLK/ DUAL

1

IO_L16P_1/A6/RHCLK4/ IRDY1

K13

RHCLK/ DUAL

1

IO_L17N_1/A3/RHCLK7

J20

RHCLK/ DUAL

1

IO_L17P_1/A4/RHCLK6

K20

RHCLK/ DUAL

0

IP_L17P_0/GCLK8

H10

GCLK

0

IP_L20N_0

G9

INPUT

0

IP_L20P_0

G8

INPUT

0

IP_L23N_0

C8

INPUT

0

IP_L23P_0

D8

INPUT

Type

0

IP_L26N_0

E6

INPUT

0

IP_L26P_0

E7

INPUT

0

IP_L29N_0

A4

INPUT

0

IP_L29P_0

A5

INPUT

0

VCCO_0

B4

VCCO

0

VCCO_0

B10

VCCO

0

VCCO_0

B16

VCCO

0

VCCO_0

D7

VCCO

1

IO_L18N_1/A1

K16

DUAL

IO_L18P_1/A2

J16

DUAL

0

VCCO_0

D13

VCCO

1

0

VCCO_0

F10

VCCO

1

IO_L19N_1/A0

J13

DUAL

IO_L19P_1

J14

I/O

J17

I/O

1

IO_L01N_1/A15

U18

DUAL

1

1

IO_L01P_1/A16

U17

DUAL

1

IO_L20N_1

1

IO_L02N_1/A13

T18

DUAL

1

IO_L20P_1

J18

I/O

IO_L21N_1

H19

I/O

1

IO_L02P_1/A14

T17

DUAL

1

1

IO_L03N_1/VREF_1

V19

VREF

1

IO_L21P_1

J19

I/O

1

IO_L03P_1

U19

I/O

1

IO_L22N_1

H15

I/O

IO_L22P_1

H16

I/O

1

IO_L04N_1

W20

I/O

1

1

IO_L04P_1

V20

I/O

1

IO_L23N_1

H18

I/O

IO_L23P_1

H17

I/O

H20

VREF

1

IO_L05N_1

R18

I/O

1

1

IO_L05P_1

R17

I/O

1

IO_L24N_1/VREF_1

1

IO_L06N_1

T20

I/O

1

IO_L24P_1

G20

I/O

IO_L25N_1

G16

I/O

F16

I/O

1

IO_L06P_1

U20

I/O

1

1

IO_L07N_1

P18

I/O

1

IO_L25P_1

1

IO_L07P_1

P17

I/O

1

IO_L26N_1

F19

I/O

IO_L26P_1

F20

I/O

1

IO_L08N_1/VREF_1

P20

VREF

1

1

IO_L08P_1

R20

I/O

1

IO_L27N_1

F18

I/O

IO_L27P_1

F17

I/O

D20

I/O

1

IO_L09N_1

P16

I/O

1

1

IO_L09P_1

N16

I/O

1

IO_L28N_1

1

IO_L10N_1

N19

I/O

1

IO_L28P_1

E20

I/O

IO_L29N_1/LDC0

D18

DUAL

1

IO_L10P_1

N18

I/O

1

1

IO_L11N_1

N15

I/O

1

IO_L29P_1/HDC

E18

DUAL

1

IO_L11P_1

M15

I/O

1

IO_L30N_1/LDC2

C19

DUAL

IO_L30P_1/LDC1

C20

DUAL

1

IO_L12N_1/A11

M18

DUAL

1

1

IO_L12P_1/A12

M17

DUAL

1

IP

B20

INPUT

IP

G15

INPUT INPUT

1

IO_L13N_1/VREF_1

L19

VREF

1

1

IO_L13P_1

M19

I/O

1

IP

G18

1

IO_L14N_1/A9/RHCLK1

L16

RHCLK/ DUAL

1

IP

H14

INPUT

1

IP

J15

INPUT

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 210

Spartan-3E FPGA Family: Pinout Descriptions Table 152: FG400 Package Pinout (Cont’d) XC3S1200E XC3S1600E Pin Name

Bank

FG400 Ball

Table 152: FG400 Package Pinout (Cont’d) Type

Bank

XC3S1200E XC3S1600E Pin Name

FG400 Ball

Type

1

IP

L18

INPUT

2

IO_L13N_2

Y8

I/O

1

IP

M20

INPUT

2

IO_L13P_2

Y9

I/O

1

IP

N14

INPUT

2

IO_L15N_2/D6/GCLK13

W10

1

IP

N20

INPUT

DUAL/ GCLK

1

IP

P15

INPUT

2

IO_L15P_2/D7/GCLK12

W9

DUAL/ GCLK

1

IP

R16

INPUT

2

IO_L16N_2/D3/GCLK15

P10

1

IP

R19

INPUT

DUAL/ GCLK

1

IP/VREF_1

E19

VREF

2

IO_L16P_2/D4/GCLK14

R10

1

IP/VREF_1

K18

VREF

DUAL/ GCLK

1

VCCO_1

D19

VCCO

2

IO_L18N_2/D1/GCLK3

V11

1

VCCO_1

G17

VCCO

DUAL/ GCLK

1

VCCO_1

K15

VCCO

2

IO_L18P_2/D2/GCLK2

V10

DUAL/ GCLK

1

VCCO_1

K19

VCCO

2

IO_L19N_2/DIN/D0

Y12

DUAL

1

VCCO_1

N17

VCCO

2

IO_L19P_2/M0

Y11

DUAL

1

VCCO_1

T19

VCCO

2

IO_L21N_2

U12

I/O

2

IO

P8

I/O

2

IO_L21P_2

V12

I/O

2

IO

P13

I/O

2

IO_L22N_2/VREF_2

W12

VREF

2

IO

R9

I/O

2

IO_L22P_2

W13

I/O

2

IO

R13

I/O

2

IO_L24N_2

U13

I/O

2

IO

W15

I/O

2

IO_L24P_2

V13

I/O

2

IO

Y5

I/O

2

IO_L25N_2

P14

I/O

2

IO

Y7

I/O

2

IO_L25P_2

R14

I/O

2

IO

Y13

I/O

2

IO_L27N_2/A22

Y14

DUAL

2

IO/D5

N11

DUAL

2

IO_L27P_2/A23

Y15

DUAL

2

IO/M1

T11

DUAL

2

IO_L28N_2

T15

I/O

2

IO/VREF_2

Y3

VREF

2

IO_L28P_2

U15

I/O

2

IO/VREF_2

Y17

VREF

2

IO_L30N_2/A20

V16

DUAL

U16

DUAL

2

IO_L01N_2/INIT_B

V4

DUAL

2

IO_L30P_2/A21

2

IO_L01P_2/CSO_B

U4

DUAL

2

IO_L31N_2/VS1/A18

Y18

DUAL

2

IO_L03N_2/MOSI/CSI_B

V5

DUAL

2

IO_L31P_2/VS2/A19

W18

DUAL

2

IO_L03P_2/DOUT/BUSY

U5

DUAL

2

IO_L32N_2/CCLK

W19

DUAL

2

IO_L04N_2

Y4

I/O

2

IO_L32P_2/VS0/A17

Y19

DUAL

2

IO_L04P_2

W4

I/O

2

IP

T16

INPUT

2

IO_L06N_2

T6

I/O

2

IP

W3

INPUT

2

IO_L06P_2

T5

I/O

2

IP_L02N_2

Y2

INPUT

2

IO_L07N_2

U7

I/O

2

IP_L02P_2

W2

INPUT

2

IO_L07P_2

V7

I/O

2

IP_L05N_2

V6

INPUT

2

IO_L09N_2/VREF_2

R7

VREF

2

IP_L05P_2

U6

INPUT

2

IO_L09P_2

T7

I/O

2

IP_L08N_2

Y6

INPUT

2

IO_L10N_2

V8

I/O

2

IP_L08P_2

W6

INPUT

2

IO_L10P_2

W8

I/O

2

IP_L11N_2

R8

INPUT

2

IO_L12N_2

U9

I/O

2

IP_L11P_2

T8

INPUT

2

IO_L12P_2

V9

I/O

2

IP_L14N_2/VREF_2

T10

VREF

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 211

Spartan-3E FPGA Family: Pinout Descriptions Table 152: FG400 Package Pinout (Cont’d) Bank

XC3S1200E XC3S1600E Pin Name

Table 152: FG400 Package Pinout (Cont’d)

FG400 Ball

Type

Bank

XC3S1200E XC3S1600E Pin Name

FG400 Ball

Type

2

IP_L14P_2

T9

INPUT

3

IO_L13P_3

K6

I/O

2

IP_L17N_2/M2/GCLK1

P12

DUAL/ GCLK

3

IO_L14N_3/LHCLK1

K2

LHCLK

3

IO_L14P_3/LHCLK0

K3

LHCLK

2

IP_L17P_2/RDWR_B/ GCLK0

P11

DUAL/ GCLK

3

IO_L15N_3/LHCLK3/IRDY2

L7

LHCLK

3

IO_L15P_3/LHCLK2

K7

LHCLK

3

IO_L16N_3/LHCLK5

L1

LHCLK

3

IO_L16P_3/LHCLK4/TRDY2

M1

LHCLK

3

IO_L17N_3/LHCLK7

L3

LHCLK

3

IO_L17P_3/LHCLK6

M3

LHCLK

3

IO_L18N_3

M7

I/O

3

IO_L18P_3

M8

I/O

3

IO_L19N_3

M4

I/O

3

IO_L19P_3

M5

I/O

3

IO_L20N_3/VREF_3

N6

VREF

3

IO_L20P_3

M6

I/O

3

IO_L21N_3

N2

I/O

3

IO_L21P_3

N1

I/O

3

IO_L22N_3

P7

I/O

3

IO_L22P_3

N7

I/O

3

IO_L23N_3

N4

I/O

3

IO_L23P_3

N3

I/O

3

IO_L24N_3

R1

I/O

3

IO_L24P_3

P1

I/O

3

IO_L25N_3

R5

I/O

3

IO_L25P_3

P5

I/O

3

IO_L26N_3

T2

I/O

3

IO_L26P_3

R2

I/O

3

IO_L27N_3

R4

I/O

3

IO_L27P_3

R3

I/O

3

IO_L28N_3/VREF_3

T1

VREF

3

IO_L28P_3

U1

I/O

3

IO_L29N_3

T3

I/O

3

IO_L29P_3

U3

I/O

3

IO_L30N_3

V1

I/O

3

IO_L30P_3

V2

I/O

3

IP

F5

INPUT

3

IP

G1

INPUT

3

IP

G6

INPUT

3

IP

H1

INPUT

3

IP

J5

INPUT

3

IP

L5

INPUT

3

IP

L8

INPUT

3

IP

M2

INPUT

2

IP_L20N_2

T12

INPUT

2

IP_L20P_2

R12

INPUT

2

IP_L23N_2/VREF_2

T13

VREF

2

IP_L23P_2

T14

INPUT

2

IP_L26N_2

V14

INPUT

2

IP_L26P_2

V15

INPUT

2

IP_L29N_2

W16

INPUT

2

IP_L29P_2

Y16

INPUT

2

VCCO_2

R11

VCCO

2

VCCO_2

U8

VCCO

2

VCCO_2

U14

VCCO

2

VCCO_2

W5

VCCO

2

VCCO_2

W11

VCCO

2

VCCO_2

W17

VCCO

3

IO_L01N_3

D2

I/O

3

IO_L01P_3

D3

I/O

3

IO_L02N_3/VREF_3

E3

VREF

3

IO_L02P_3

E4

I/O

3

IO_L03N_3

C1

I/O

3

IO_L03P_3

B1

I/O

3

IO_L04N_3

E1

I/O

3

IO_L04P_3

D1

I/O

3

IO_L05N_3

F3

I/O

3

IO_L05P_3

F4

I/O

3

IO_L06N_3

F1

I/O

3

IO_L06P_3

F2

I/O

3

IO_L07N_3

G4

I/O

3

IO_L07P_3

G3

I/O

3

IO_L08N_3

G5

I/O

3

IO_L08P_3

H5

I/O

3

IO_L09N_3/VREF_3

H3

VREF

3

IO_L09P_3

H2

I/O

3

IO_L10N_3

H7

I/O

3

IO_L10P_3

H6

I/O

3

IO_L11N_3

J4

I/O

3

IO_L11P_3

J3

I/O

3

IO_L12N_3

J1

I/O

3

IO_L12P_3

J2

I/O

3

IO_L13N_3

J6

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 212

Spartan-3E FPGA Family: Pinout Descriptions Table 152: FG400 Package Pinout (Cont’d) XC3S1200E XC3S1600E Pin Name

Bank

Table 152: FG400 Package Pinout (Cont’d)

FG400 Ball

Type

Bank

XC3S1200E XC3S1600E Pin Name

FG400 Ball

Type

3

IP

N5

INPUT

GND

GND

P19

GND

3

IP

P3

INPUT

GND

GND

R6

GND

3

IP

T4

INPUT

GND

GND

R15

GND

3

IP

W1

INPUT

GND

GND

U11

GND

3

IP/VREF_3

K5

VREF

GND

GND

V3

GND

3

IP/VREF_3

P6

VREF

GND

GND

V18

GND

3

VCCO_3

E2

VCCO

GND

GND

W7

GND

3

VCCO_3

H4

VCCO

GND

GND

W14

GND

3

VCCO_3

L2

VCCO

GND

GND

Y1

GND

3

VCCO_3

L6

VCCO

GND

GND

Y10

GND

3

VCCO_3

P4

VCCO

GND

GND

Y20

GND

VCCO_3

U2

VCCO

VCCAUX DONE

V17

CONFIG

GND

3

GND

A1

GND

VCCAUX PROG_B

C2

CONFIG

GND

GND

A11

GND

VCCAUX TCK

D17

JTAG

GND

GND

A20

GND

VCCAUX TDI

B3

JTAG

GND

GND

B7

GND

VCCAUX TDO

B19

JTAG

GND

GND

B14

GND

VCCAUX TMS

E17

JTAG

GND

GND

C3

GND

VCCAUX VCCAUX

D11

VCCAUX

GND

GND

C18

GND

VCCAUX VCCAUX

H12

VCCAUX

GND

GND

D10

GND

VCCAUX VCCAUX

J7

VCCAUX

GND

GND

F6

GND

VCCAUX VCCAUX

K4

VCCAUX

GND

GND

F15

GND

VCCAUX VCCAUX

L17

VCCAUX

GND

GND

G2

GND

VCCAUX VCCAUX

M14

VCCAUX

GND

GND

G12

GND

VCCAUX VCCAUX

N9

VCCAUX

GND

GND

G19

GND

VCCAUX VCCAUX

U10

VCCAUX

GND

GND

H8

GND

VCCINT

VCCINT

H9

VCCINT

GND

GND

J9

GND

VCCINT

VCCINT

H11

VCCINT

GND

GND

J11

GND

VCCINT

VCCINT

H13

VCCINT

GND

GND

K1

GND

VCCINT

VCCINT

J8

VCCINT

GND

GND

K8

GND

VCCINT

VCCINT

J10

VCCINT

GND

GND

K10

GND

VCCINT

VCCINT

J12

VCCINT

GND

GND

K12

GND

VCCINT

VCCINT

K9

VCCINT

GND

GND

K17

GND

VCCINT

VCCINT

K11

VCCINT

GND

GND

L4

GND

VCCINT

VCCINT

L10

VCCINT

GND

GND

L9

GND

VCCINT

VCCINT

L12

VCCINT

GND

GND

L11

GND

VCCINT

VCCINT

M9

VCCINT

GND

GND

L13

GND

VCCINT

VCCINT

M11

VCCINT

GND

GND

L20

GND

VCCINT

VCCINT

M13

VCCINT

GND

GND

M10

GND

VCCINT

VCCINT

N8

VCCINT

GND

GND

M12

GND

VCCINT

VCCINT

N10

VCCINT

GND

GND

N13

GND

VCCINT

VCCINT

N12

VCCINT

GND

GND

P2

GND

GND

GND

P9

GND

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 213

Spartan-3E FPGA Family: Pinout Descriptions

User I/Os by Bank Table 153 indicates how the 304 available user-I/O pins are distributed between the four I/O banks on the FG400 package. Table 153: User I/Os Per Bank for the XC3S1200E and XC3S1600E in the FG400 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

78

43

20

1

6

8

1

74

35

12

21

6

0(2)

Bottom

2

78

30

18

24

6

0(2)

Left

3

74

48

12

0

6

8

304

156

62

46

24

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

Footprint Migration Differences The XC3S1200E and XC3S1600E FPGAs have identical footprints in the FG400 package. Designs can migrate between the XC3S1200E and XC3S1600E FPGAs without further consideration.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 214

Spartan-3E FPGA Family: Pinout Descriptions

FG400 Footprint

X-Ref Target - Figure 87

Bank 0

Left Half of Package (top view)

1

2 I/O

3

4

INPUT

I/O

I/O

L29P_0

L25N_0

L25P_0

B

I/O

I/O

I/O: Unrestricted, 156 general-purpose user I/O

L03P_3

L31P_0

INPUT: Unrestricted, 62 general-purpose input pin

C

L03N_3

DUAL: Configuration pin, 46 then possible user I/O

D

I/O

I/O

I/O

L04P_3

L01N_3

L01P_3

VREF: User I/O or input

E

L04N_3

VCCO_3

L02N_3 VREF_3

CLK: User I/O, input, or 16 clock buffer input

F

I/O

I/O

I/O

I/O

L06N_3

L06P_3

L05N_3

L05P_3

GND

24 voltage reference for bank

I/O

PROG_B

TDI

GND

I/O

I/O

VCCO_0

I/O L32P_0

I/O L32N_0 HSWAP

I/O L02P_3

INPUT

GND: Ground

J

I/O

I/O

I/O

I/O

L12N_3

L12P_3

L11P_3

L11N_3

VCCO: Output voltage

I/O

I/O

K

GND

L14N_3 LHCLK1

L14P_3 LHCLK0

L

L16N_3 LHCLK5

VCCO_3

L17N_3 LHCLK7

L16P_3 LHCLK4 TRDY2

INPUT

L17P_3 LHCLK6

Bank 3

H

VCCINT: Internal core

I/O

I/O L28N_0

INPUT

I/O L09N_3 VREF_3

VCCO_3

VCCAUX

I/O

GND

L24N_0 VREF_0

INPUT

I/O

I/O

I/O L10N_3

I/O L13N_3

INPUT

I/O

VREF_3

L13P_3

INPUT

VCCO_3

L24P_3

GND

INPUT

VCCO_3

R

I/O

I/O

I/O

I/O

I/O

L24N_3

L26P_3

L27P_3

L27N_3

L25N_3

I/O

I/O

L30N_3

L30P_3

W

INPUT

Y

GND

INPUT L02P_2

GND

INPUT

GND I/O L16N_0 GCLK7

I/O L19N_0

INPUT

INPUT

L20P_0

L20N_0

GND

VCCINT

L17P_0 GCLK8

VCCINT

GND

VCCINT

GND

VCCINT

GND

INPUT

GND

VCCINT

VCCINT

GND

VCCO_0

INPUT L17N_0 GCLK9

INPUT

I/O L15P_3 LHCLK2 L15N_3 LHCLK3 IRDY2

L20N_3 VREF_3

P

V

I/O

I/O

INPUT

I/O

L29P_3

I/O L19P_0

VCCO_0

L24P_0

I/O

L23N_3

L28P_3

I/O

L18P_3

I/O

I/O

L21P_0

I/O

L23P_3

VCCO_3

I/O

L23P_0

L18N_3

I/O

U

INPUT

I/O

L21N_3

I/O

I/O L22P_0

I/O

L20P_3

I/O

L29N_3

L18P_0 GCLK10

L21N_0

I/O

L21P_3

I/O

L18N_0 GCLK11

L23N_0

L19P_3

N

L26N_3

10 I/O

INPUT

I/O

N.C.: Not connected

I/O

VCCAUX

L22N_0 VREF_0

L19N_3

0

L28N_3 VREF_3

I/O

9 I/O

I/O GND

M

I/O

L26P_0

L10P_3

VCCAUX: Auxiliary supply voltage (+2.5V)

T

INPUT

L26N_0

I/O

8

I/O

VCCO_0

INPUT

I/O

I/O

I/O

L08P_3

INPUT

8

I/O GND

I/O INPUT

I/O

JTAG: Dedicated JTAG port pins

16 supply voltage (+1.2V)

I/O

L08N_3

4

I/O L28P_0

L30P_0

I/O

INPUT

24 supply for bank

I/O L30N_0 VREF_0

L07N_3

G

42

I/O L27P_0

I/O

CONFIG: Dedicated configuration pins

I/O

I/O L27N_0

L07P_3

2

L09P_3

7

L29N_0

GND

I/O

6

INPUT

A

L31N_0

5

INPUT

I/O

I/O

INPUT

I/O

L25P_3

VREF_3

L22N_3

GND

L09N_2 VREF_2

INPUT

L11P_2

L14P_2

I/O

I/O

I/O

INPUT

L03N_2 MOSI CSI_B

L04N_2

L16P_2 D4 GCLK14

I/O

I/O

I/O

I/O

L09P_2

L01N_2 INIT_B

VREF_2

L11N_2

L16N_2 D3 GCLK15

I/O

I/O

L02N_2

INPUT

GND

L06N_2

L03P_2 DOUT BUSY

INPUT

I/O I/O

I/O

I/O

I/O

I/O

VCCINT VCCAUX VCCINT

L06P_2

L01P_2 CSO_B

L04P_2

I/O L22P_3

INPUT

I/O

L05P_2

L07N_2

I/O

I/O

I/O

L05N_2

L07P_2

L10N_2

L12P_2

L08P_2

INPUT

I/O

I/O L12N_2

INPUT

INPUT

VCCO_2

VCCO_2

L08N_2

Bank 2

GND

I/O

I/O L10P_2

INPUT L14N_2 VREF_2

VCCAUX

I/O L18P_2 D2 GCLK2

I/O

I/O

L15P_2 D7 GCLK12

L15N_2 D6 GCLK13

I/O

I/O

L13N_2

L13P_2

GND

DS312-4_08_101905

Figure 87: FG400 Package Footprint (top view)

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 215

Spartan-3E FPGA Family: Pinout Descriptions

FG400 Footprint

Bank 0 12

13

14

I/O GND

I/O

INPUT

INPUT

I/O

L14N_0

L14P_0

L10N_0

L09N_0 VREF_0

15

16

17

I/O

I/O

I/O

I/O

L09P_0

L06N_0

L04P_0

L04N_0

GND

I/O L06P_0

VCCO_0

I/O L01N_0

I/O

I/O

I/O

I/O

INPUT

INPUT

I/O

VREF_0

L12N_0

L10P_0

L07N_0

L05P_0

L02N_0

L01P_0

VCCAUX

I/O L16P_0 GCLK6

I/O L15P_0 GCLK4

I/O L12P_0

I/O L13N_0

I/O L13P_0

I/O L15N_0 GCLK5

GND

I/O

INPUT

INPUT

L07P_0

L05N_0

L02P_0

INPUT

INPUT

L08N_0

L08P_0

I/O

I/O

GND

INPUT

INPUT

L11P_0

L11N_0

VCCO_0

I/O

VCCINT VCCAUX VCCINT

INPUT

I/O GND

VCCINT

VCCINT

GND

GND

VCCINT

VCCINT

GND

L19N_1 A0

I/O L19P_1

I/O

L16P_1 A6 RHCLK4 IRDY1

I/O D5

VCCINT

INPUT

INPUT

L17P_2 RDWR_B GCLK0

L17N_2 M2 GCLK1

VCCO_2

INPUT L20P_2

I/O

INPUT

M1

L20N_2

GND I/O L18N_2 D1 GCLK3

VCCINT VCCAUX

GND

I/O

I/O INPUT L23N_2 VREF_2

I/O

I/O

L21N_2

L24N_2

INPUT

I/O L25N_2

I/O L25P_2

I/O

I/O

I/O

I/O

I/O

L27P_1

L27N_1

L26N_1

L26P_1

VCCO_1

INPUT

GND

I/O L25N_1

I/O

I/O

I/O

L20N_1

L20P_1

L21P_1

I/O

I/O

I/O

L15P_1 A8 RHCLK2

L14N_1 A9 RHCLK1

I/O

I/O

I/O

I/O

L27N_2 A22

L27P_2 A23

INPUT I/O L12N_1 A11

VCCO_1

I/O L07N_1

J

K

GND

L

INPUT

M

INPUT

N

I/O

I/O

L05P_1

L05N_1

I/O

I/O

L02P_1 A14

L02N_1 A13

INPUT

VCCO_1

I/O

I/O

I/O

L01P_1 A16

L01N_1 A15

DONE

GND I/O

I/O

VCCO_2

L31P_2 VS2 A19

L32N_2 CCLK

I/O

L08N_1 VREF_1

I/O

L29P_2

VREF_2

I/O L06N_1

I/O

I/O L06P_1

I/O

INPUT

I/O L08P_1

L03P_1

L03N_1 VREF_1

I/O

I/O

L31N_2 VS1 A18

L32P_2 VS0 A17

Bank 2

DS312 (v4.1) July 19, 2013 Product Specification

H

I/O GND

L30P_2 A21

L29N_2

G

L17P_1 A4 RHCLK6

I/O

I/O

I/O

INPUT

F

I/O L17N_1 A3 RHCLK7

L13P_1

L10N_1

L07P_1

L30N_2 A20

E

I/O L24N_1 VREF_1

L13N_1 VREF_1

I/O

I/O

INPUT

D

I/O VCCO_1

L10P_1

L09N_1

INPUT

I/O L24P_1

Right Half of Package (top view)

C

I/O VCCAUX

I/O

I/O

L28P_2

VREF_1

L12P_1 A12

L09P_1

I/O

INPUT

I/O

I/O

L28N_2

GND

L14P_1 A10 RHCLK0

L11N_1

GND

I/O

I/O L28P_1

L18N_1 A1

L26P_2

I/O

INPUT VREF_1

VCCO_1

INPUT

L19N_2 DIN D0

L29P_1 HDC

L28N_1

L25P_1

I/O

L26N_2

I/O

TMS

I/O

VCCO_1

L18P_1 A2

INPUT

L19P_2 M0

L29N_1 LDC0

INPUT

I/O

I/O

I/O TCK

I/O

L24P_2

L22P_2

I/O L30P_1 LDC1

L21N_1

I/O

L22N_2 VREF_2

I/O

I/O

L23P_2

B

L30N_1 LDC2

L23N_1

GND

INPUT

GND

I/O

INPUT

A

TDO

L23P_1

I/O

GND

INPUT

I/O

INPUT

VCCO_2

I/O L03P_0

L22P_1

L11P_1

20

L03N_0 VREF_0

I/O I/O

19

I/O

L21P_2

I/O VCCO_2

L15N_1 A7 RHCLK3 TRDY1

I/O

L22N_1

I/O L16N_1 A5 RHCLK5

I/O

GND

INPUT

18

Bank 1

11

I/O L04P_1

I/O

P

R

T

U

V

L04N_1

W

GND

Y

DS312-4_09_101905

www.xilinx.com 216

Spartan-3E FPGA Family: Pinout Descriptions

FG484: 484-ball Fine-pitch Ball Grid Array The 484-ball fine-pitch ball grid array, FG484, supports the XC3S1600E FPGA.

Table 154: FG484 Package Pinout (Cont’d) Bank

Table 154 lists all the FG484 package pins. They are sorted by bank number and then by pin name. Pairs of pins that form a differential I/O pair appear together in the table. The table also shows the pin number for each pin and the pin type, as defined earlier.

XC3S1600E Pin Name

FG484 Ball

Type

0

IO_L12P_0

A15

I/O

0

IO_L13N_0

H14

I/O

0

IO_L13P_0

G14

I/O

0

IO_L15N_0

G13

I/O

An electronic version of this package pinout table and footprint diagram is available for download from the Xilinx website at:

0

IO_L15P_0

F13

I/O

0

IO_L16N_0

J13

I/O

0

IO_L16P_0

H13

I/O

http://www.xilinx.com/support/documentation/data_sheets /s3e_pin.zip

0

IO_L18N_0/GCLK5

E12

GCLK

0

IO_L18P_0/GCLK4

F12

GCLK

Pinout Table

0

IO_L19N_0/GCLK7

C12

GCLK

0

IO_L19P_0/GCLK6

B12

GCLK

0

IO_L21N_0/GCLK11

B11

GCLK

0

IO_L21P_0/GCLK10

C11

GCLK

0

IO_L22N_0

D11

I/O

0

IO_L22P_0

E11

I/O

0

IO_L24N_0

A9

I/O

Table 154: FG484 Package Pinout Bank

XC3S1600E Pin Name

FG484 Ball

Type

0

IO

B6

I/O

0

IO

B13

I/O

0

IO

C5

I/O

0

IO

C14

I/O

0

IO

E16

I/O

0

IO

F9

I/O

0

IO

F16

I/O

0

IO

G8

I/O

0

IO

H10

I/O

0

IO

H15

I/O

0

IO

J11

I/O

0

IO/VREF_0

G12

VREF

0

IO_L01N_0

C18

I/O

0

IO_L01P_0

C19

I/O

0

IO_L03N_0/VREF_0

A20

VREF

0

IO_L03P_0

A21

I/O

0

IO_L04N_0

A19

I/O

0

IO_L04P_0

A18

I/O

0

IO_L06N_0

C16

I/O

0

IO_L06P_0

D16

I/O

0

IO_L07N_0

A16

I/O

0

IO_L07P_0

A17

I/O

0

IO_L09N_0/VREF_0

B15

VREF

0

IO_L09P_0

C15

I/O

0

IO_L10N_0

G15

I/O

0

IO_L10P_0

F15

I/O

0

IO_L11N_0

D14

I/O

0

IO_L11P_0

E14

I/O

0

IO_L12N_0/VREF_0

A14

VREF

DS312 (v4.1) July 19, 2013 Product Specification

0

IO_L24P_0

A10

I/O

0

IO_L25N_0/VREF_0

D10

VREF

0

IO_L25P_0

C10

I/O

0

IO_L27N_0

H8

I/O

0

IO_L27P_0

H9

I/O

0

IO_L28N_0

C9

I/O

0

IO_L28P_0

B9

I/O

0

IO_L29N_0

E9

I/O

0

IO_L29P_0

D9

I/O

0

IO_L30N_0

B8

I/O

0

IO_L30P_0

A8

I/O

0

IO_L32N_0/VREF_0

F7

VREF

0

IO_L32P_0

F8

I/O

0

IO_L33N_0

A6

I/O

0

IO_L33P_0

A7

I/O

0

IO_L35N_0

A4

I/O

0

IO_L35P_0

A5

I/O

0

IO_L36N_0

E7

I/O

0

IO_L36P_0

D7

I/O

0

IO_L38N_0/VREF_0

D6

VREF

0

IO_L38P_0

D5

I/O

0

IO_L39N_0

B4

I/O

0

IO_L39P_0

B3

I/O

0

IO_L40N_0/HSWAP

D4

DUAL

0

IO_L40P_0

C4

I/O

0

IP

B19

INPUT

www.xilinx.com 217

Spartan-3E FPGA Family: Pinout Descriptions Table 154: FG484 Package Pinout (Cont’d)

Table 154: FG484 Package Pinout (Cont’d)

Bank

XC3S1600E Pin Name

FG484 Ball

Type

Bank

XC3S1600E Pin Name

FG484 Ball

Type

0

IP

E6

INPUT

1

IO_L08N_1

T22

I/O

0

IP_L02N_0

D17

INPUT

1

IO_L08P_1

U22

I/O

0

IP_L02P_0

D18

INPUT

1

IO_L09N_1

R19

I/O

0

IP_L05N_0

C17

INPUT

1

IO_L09P_1

R18

I/O

0

IP_L05P_0

B17

INPUT

1

IO_L10N_1

R16

I/O

0

IP_L08N_0

E15

INPUT

1

IO_L10P_1

T16

I/O

0

IP_L08P_0

D15

INPUT

1

IO_L11N_1

R21

I/O

0

IP_L14N_0

D13

INPUT

1

IO_L11P_1

R20

I/O

0

IP_L14P_0

C13

INPUT

1

IO_L12N_1/VREF_1

P18

VREF

0

IP_L17N_0

A12

INPUT

1

IO_L12P_1

P17

I/O

0

IP_L17P_0

A13

INPUT

1

IO_L13N_1

P22

I/O

0

IP_L20N_0/GCLK9

H11

GCLK

1

IO_L13P_1

R22

I/O

0

IP_L20P_0/GCLK8

H12

GCLK

1

IO_L14N_1

P15

I/O

0

IP_L23N_0

F10

INPUT

1

IO_L14P_1

P16

I/O

0

IP_L23P_0

F11

INPUT

1

IO_L15N_1

N18

I/O

0

IP_L26N_0

G9

INPUT

1

IO_L15P_1

N19

I/O

0

IP_L26P_0

G10

INPUT

1

IO_L16N_1/A11

N16

DUAL

0

IP_L31N_0

C8

INPUT

1

IO_L16P_1/A12

N17

DUAL

0

IP_L31P_0

D8

INPUT

1

IO_L17N_1/VREF_1

M20

VREF

0

IP_L34N_0

C7

INPUT

1

IO_L17P_1

N20

I/O

0

IP_L34P_0

C6

INPUT

1

IO_L18N_1/A9/RHCLK1

M22

0

IP_L37N_0

A3

INPUT

RHCLK/ DUAL

0

IP_L37P_0

A2

INPUT

1

IO_L18P_1/A10/RHCLK0

N22

RHCLK/ DUAL

0

VCCO_0

B5

VCCO

1

VCCO_0

B10

VCCO

IO_L19N_1/A7/RHCLK3/ TRDY1

M16

0

RHCLK/ DUAL

0

VCCO_0

B14

VCCO

1

IO_L19P_1/A8/RHCLK2

M15

0

VCCO_0

B18

VCCO

RHCLK/ DUAL

0

VCCO_0

E8

VCCO

1

IO_L20N_1/A5/RHCLK5

L21

0

VCCO_0

F14

VCCO

RHCLK/ DUAL

0

VCCO_0

G11

VCCO

1

IO_L20P_1/A6/RHCLK4/ IRDY1

L20

RHCLK/ DUAL

1

IO_L01N_1/A15

Y22

DUAL

1

IO_L21N_1/A3/RHCLK7

L19

1

IO_L01P_1/A16

AA22

DUAL

RHCLK/ DUAL

1

IO_L02N_1/A13

W21

DUAL

1

IO_L21P_1/A4/RHCLK6

L18

RHCLK/ DUAL

1

IO_L22N_1/A1

K22

DUAL

1

IO_L22P_1/A2

L22

DUAL

1

IO_L23N_1/A0

K17

DUAL

1

IO_L23P_1

K16

I/O

1

IO_L24N_1

K19

I/O

1

IO_L24P_1

K18

I/O

1

IO_L25N_1

K15

I/O

1

IO_L25P_1

J15

I/O

1

IO_L26N_1

J20

I/O

1

IO_L26P_1

J21

I/O

1

IO_L02P_1/A14

Y21

DUAL

1

IO_L03N_1/VREF_1

W20

VREF

1

IO_L03P_1

V20

I/O

1

IO_L04N_1

U19

I/O

1

IO_L04P_1

V19

I/O

1

IO_L05N_1

V22

I/O

1

IO_L05P_1

W22

I/O

1

IO_L06N_1

T19

I/O

1

IO_L06P_1

T18

I/O

1

IO_L07N_1/VREF_1

U20

VREF

1

IO_L07P_1

U21

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 218

Spartan-3E FPGA Family: Pinout Descriptions Table 154: FG484 Package Pinout (Cont’d)

Table 154: FG484 Package Pinout (Cont’d)

Bank

XC3S1600E Pin Name

FG484 Ball

Type

Bank

XC3S1600E Pin Name

FG484 Ball

Type

1

IO_L27N_1

J17

I/O

1

VCCO_1

K21

VCCO

1

IO_L27P_1

J18

I/O

1

VCCO_1

L16

VCCO

1

IO_L28N_1/VREF_1

H21

VREF

1

VCCO_1

P21

VCCO

1

IO_L28P_1

H22

I/O

1

VCCO_1

R17

VCCO

1

IO_L29N_1

H20

I/O

1

VCCO_1

V21

VCCO

1

IO_L29P_1

H19

I/O

2

IO

Y8

I/O

1

IO_L30N_1

H17

I/O

2

IO

Y9

I/O

1

IO_L30P_1

G17

I/O

2

IO

AA10

I/O

1

IO_L31N_1

F22

I/O

2

IO

AB5

I/O

1

IO_L31P_1

G22

I/O

2

IO

AB13

I/O

1

IO_L32N_1

F20

I/O

2

IO

AB14

I/O

1

IO_L32P_1

G20

I/O

2

IO

AB16

I/O

1

IO_L33N_1

G18

I/O

2

IO

AB18

I/O

1

IO_L33P_1

G19

I/O

2

IO/D5

AB11

DUAL

1

IO_L34N_1

D22

I/O

2

IO/M1

AA12

DUAL

1

IO_L34P_1

E22

I/O

2

IO/VREF_2

AB4

VREF

1

IO_L35N_1

F19

I/O

2

IO/VREF_2

AB21

VREF

1

IO_L35P_1

F18

I/O

2

IO_L01N_2/INIT_B

AB3

DUAL

1

IO_L36N_1

E20

I/O

2

IO_L01P_2/CSO_B

AA3

DUAL

1

IO_L36P_1

E19

I/O

2

IO_L03N_2/MOSI/CSI_B

Y5

DUAL

1

IO_L37N_1/LDC0

C21

DUAL

2

IO_L03P_2/DOUT/BUSY

W5

DUAL

1

IO_L37P_1/HDC

C22

DUAL

2

IO_L04N_2

W6

I/O

1

IO_L38N_1/LDC2

B21

DUAL

2

IO_L04P_2

V6

I/O

1

IO_L38P_1/LDC1

B22

DUAL

2

IO_L06N_2

W7

I/O

1

IP

D20

INPUT

2

IO_L06P_2

Y7

I/O

1

IP

F21

INPUT

2

IO_L07N_2

U7

I/O

1

IP

G16

INPUT

2

IO_L07P_2

V7

I/O

1

IP

H16

INPUT

2

IO_L09N_2/VREF_2

V8

VREF

1

IP

J16

INPUT

2

IO_L09P_2

W8

I/O

1

IP

J22

INPUT

2

IO_L10N_2

T8

I/O

1

IP

K20

INPUT

2

IO_L10P_2

U8

I/O

1

IP

L15

INPUT

2

IO_L11N_2

AB8

I/O

1

IP

M18

INPUT

2

IO_L11P_2

AA8

I/O

1

IP

N15

INPUT

2

IO_L12N_2

W9

I/O

1

IP

N21

INPUT

2

IO_L12P_2

V9

I/O

1

IP

P20

INPUT

2

IO_L13N_2/VREF_2

R9

VREF

1

IP

R15

INPUT

2

IO_L13P_2

T9

I/O

1

IP

T17

INPUT

2

IO_L14N_2

AB9

I/O

1

IP

T20

INPUT

2

IO_L14P_2

AB10

I/O

1

IP

U18

INPUT

2

IO_L16N_2

U10

I/O

1

IP/VREF_1

D21

VREF

2

IO_L16P_2

T10

I/O

1

IP/VREF_1

L17

VREF

2

IO_L17N_2

R10

I/O

1

VCCO_1

E21

VCCO

2

IO_L17P_2

P10

I/O

1

VCCO_1

H18

VCCO

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 219

Spartan-3E FPGA Family: Pinout Descriptions Table 154: FG484 Package Pinout (Cont’d) Bank

XC3S1600E Pin Name

FG484 Ball

2

IO_L19N_2/D6/GCLK13

2 2

Table 154: FG484 Package Pinout (Cont’d) Type

Bank

XC3S1600E Pin Name

FG484 Ball

Type

U11

DUAL/ GCLK

2

IP_L08N_2

AB7

INPUT

2

IP_L08P_2

AB6

INPUT

IO_L19P_2/D7/GCLK12

V11

DUAL/ GCLK

2

IP_L15N_2

Y10

INPUT

IO_L20N_2/D3/GCLK15

T11

DUAL/ GCLK

2

IP_L15P_2

W10

INPUT

2

IP_L18N_2/VREF_2

AA11

VREF

2

IP_L18P_2

Y11

INPUT

2

IO_L20P_2/D4/GCLK14

R11

DUAL/ GCLK

2

IP_L21N_2/M2/GCLK1

P12

2

IO_L22N_2/D1/GCLK3

W12

DUAL/ GCLK

DUAL/ GCLK

2

IP_L21P_2/RDWR_B/ GCLK0

R12

2

IO_L22P_2/D2/GCLK2

Y12

DUAL/ GCLK

DUAL/ GCLK

2

IP_L24N_2

R13

INPUT

2

IO_L23N_2/DIN/D0

U12

DUAL

2

IP_L24P_2

T13

INPUT

2

IO_L23P_2/M0

V12

DUAL

2

IP_L31N_2/VREF_2

T15

VREF

2

IO_L25N_2

Y13

I/O

2

IP_L31P_2

U15

INPUT

2

IO_L25P_2

W13

I/O

2

IP_L34N_2

Y16

INPUT

2

IO_L26N_2/VREF_2

U14

VREF

2

IP_L34P_2

W16

INPUT

2

IO_L26P_2

U13

I/O

2

IP_L37N_2

AA19

INPUT

2

IO_L27N_2

T14

I/O

2

IP_L37P_2

AB19

INPUT

2

IO_L27P_2

R14

I/O

2

VCCO_2

T12

VCCO

2

IO_L28N_2

Y14

I/O

2

VCCO_2

U9

VCCO

2

IO_L28P_2

AA14

I/O

2

VCCO_2

V15

VCCO

2

IO_L29N_2

W14

I/O

2

VCCO_2

AA5

VCCO

2

IO_L29P_2

V14

I/O

2

VCCO_2

AA9

VCCO

2

IO_L30N_2

AB15

I/O

2

VCCO_2

AA13

VCCO

2

IO_L30P_2

AA15

I/O

2

VCCO_2

AA18

VCCO

2

IO_L32N_2

W15

I/O

3

IO_L01N_3

C1

I/O

2

IO_L32P_2

Y15

I/O

3

IO_L01P_3

C2

I/O

2

IO_L33N_2

U16

I/O

3

IO_L02N_3/VREF_3

D2

VREF

2

IO_L33P_2

V16

I/O

3

IO_L02P_3

D3

I/O

2

IO_L35N_2/A22

AB17

DUAL

3

IO_L03N_3

E3

I/O

2

IO_L35P_2/A23

AA17

DUAL

3

IO_L03P_3

E4

I/O

2

IO_L36N_2

W17

I/O

3

IO_L04N_3

E1

I/O

2

IO_L36P_2

Y17

I/O

3

IO_L04P_3

D1

I/O

2

IO_L38N_2/A20

Y18

DUAL

3

IO_L05N_3

F4

I/O

2

IO_L38P_2/A21

W18

DUAL

3

IO_L05P_3

F3

I/O

2

IO_L39N_2/VS1/A18

AA20

DUAL

3

IO_L06N_3

G5

I/O

2

IO_L39P_2/VS2/A19

AB20

DUAL

3

IO_L06P_3

G4

I/O

2

IO_L40N_2/CCLK

W19

DUAL

3

IO_L07N_3

F1

I/O

2

IO_L40P_2/VS0/A17

Y19

DUAL

3

IO_L07P_3

G1

I/O

2

IP

V17

INPUT

3

IO_L08N_3/VREF_3

G6

VREF

2

IP

AB2

INPUT

3

IO_L08P_3

G7

I/O

2

IP_L02N_2

AA4

INPUT

3

IO_L09N_3

H4

I/O

2

IP_L02P_2

Y4

INPUT

3

IO_L09P_3

H5

I/O

2

IP_L05N_2

Y6

INPUT

3

IO_L10N_3

H2

I/O

2

IP_L05P_2

AA6

INPUT

3

IO_L10P_3

H3

I/O

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 220

Spartan-3E FPGA Family: Pinout Descriptions Table 154: FG484 Package Pinout (Cont’d)

Table 154: FG484 Package Pinout (Cont’d)

Bank

XC3S1600E Pin Name

FG484 Ball

Type

Bank

XC3S1600E Pin Name

FG484 Ball

Type

3

IO_L11N_3

H1

I/O

3

IO_L33N_3

W1

I/O

3

IO_L11P_3

J1

I/O

3

IO_L33P_3

V1

I/O

3

IO_L12N_3

J6

I/O

3

IO_L34N_3

U4

I/O

3

IO_L12P_3

J5

I/O

3

IO_L34P_3

U3

I/O

3

IO_L13N_3/VREF_3

J3

VREF

3

IO_L35N_3

V4

I/O

3

IO_L13P_3

K3

I/O

3

IO_L35P_3

V3

I/O

3

IO_L14N_3

J8

I/O

3

IO_L36N_3/VREF_3

W3

VREF

3

IO_L14P_3

K8

I/O

3

IO_L36P_3

W2

I/O

3

IO_L15N_3

K4

I/O

3

IO_L37N_3

Y2

I/O

3

IO_L15P_3

K5

I/O

3

IO_L37P_3

Y1

I/O

3

IO_L16N_3

K1

I/O

3

IO_L38N_3

AA1

I/O

3

IO_L16P_3

L1

I/O

3

IO_L38P_3

AA2

I/O

3

IO_L17N_3

L7

I/O

3

IP

F2

INPUT

3

IO_L17P_3

K7

I/O

3

IP

F5

INPUT

3

IO_L18N_3/LHCLK1

L5

LHCLK

3

IP

G3

INPUT

3

IO_L18P_3/LHCLK0

M5

LHCLK

3

IP

H7

INPUT

3

IO_L19N_3/LHCLK3/IRDY2

M8

LHCLK

3

IP

J7

INPUT

3

IO_L19P_3/LHCLK2

L8

LHCLK

3

IP

K2

INPUT

3

IO_L20N_3/LHCLK5

N1

LHCLK

3

IP

K6

INPUT

3

IO_L20P_3/LHCLK4/TRDY2

M1

LHCLK

3

IP

M2

INPUT

3

IO_L21N_3/LHCLK7

M4

LHCLK

3

IP

M6

INPUT

3

IO_L21P_3/LHCLK6

M3

LHCLK

3

IP

N3

INPUT

3

IO_L22N_3

N6

I/O

3

IP

P3

INPUT

3

IO_L22P_3

N7

I/O

3

IP

R8

INPUT

3

IO_L23N_3

P8

I/O

3

IP

T1

INPUT

3

IO_L23P_3

N8

I/O

3

IP

T7

INPUT

3

IO_L24N_3/VREF_3

N4

VREF

3

IP

U5

INPUT

3

IO_L24P_3

N5

I/O

3

IP

W4

INPUT

3

IO_L25N_3

P2

I/O

3

IP/VREF_3

L3

VREF

3

IO_L25P_3

P1

I/O

3

IP/VREF_3

T3

VREF

3

IO_L26N_3

R7

I/O

3

VCCO_3

E2

VCCO

3

IO_L26P_3

P7

I/O

3

VCCO_3

H6

VCCO

3

IO_L27N_3

P6

I/O

3

VCCO_3

J2

VCCO

3

IO_L27P_3

P5

I/O

3

VCCO_3

M7

VCCO

3

IO_L28N_3

R2

I/O

3

VCCO_3

N2

VCCO

3

IO_L28P_3

R1

I/O

3

VCCO_3

R5

VCCO

3

IO_L29N_3

R3

I/O

3

VCCO_3

V2

VCCO

3

IO_L29P_3

R4

I/O

GND

GND

A1

GND

3

IO_L30N_3

T6

I/O

GND

GND

A11

GND

3

IO_L30P_3

R6

I/O

GND

GND

A22

GND

3

IO_L31N_3

U2

I/O

GND

GND

B7

GND

3

IO_L31P_3

U1

I/O

GND

GND

B16

GND

3

IO_L32N_3

T4

I/O

GND

GND

C3

GND

3

IO_L32P_3

T5

I/O

GND

GND

C20

GND

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 221

Spartan-3E FPGA Family: Pinout Descriptions Table 154: FG484 Package Pinout (Cont’d)

Table 154: FG484 Package Pinout (Cont’d)

Bank

XC3S1600E Pin Name

FG484 Ball

Type

Bank

XC3S1600E Pin Name

FG484 Ball

Type

GND

GND

E10

GND

GND

GND

AB1

GND

GND

GND

E13

GND

GND

GND

AB12

GND

GND

GND

F6

GND

GND

GND

AB22

GND

GND

GND

F17

GND

VCCAUX

DONE

AA21

CONFIG

GND

GND

G2

GND

VCCAUX

PROG_B

B1

CONFIG

GND

GND

G21

GND

VCCAUX

TCK

E17

JTAG

GND

GND

J4

GND

VCCAUX

TDI

B2

JTAG

GND

GND

J9

GND

VCCAUX

TDO

B20

JTAG

GND

GND

J12

GND

VCCAUX

TMS

D19

JTAG

GND

GND

J14

GND

VCCAUX

VCCAUX

D12

VCCAUX

GND

GND

J19

GND

VCCAUX

VCCAUX

E5

VCCAUX

GND

GND

K10

GND

VCCAUX

VCCAUX

E18

VCCAUX

GND

GND

K12

GND

VCCAUX

VCCAUX

K14

VCCAUX

GND

GND

L2

GND

VCCAUX

VCCAUX

L4

VCCAUX

GND

GND

L6

GND

VCCAUX

VCCAUX

M19

VCCAUX

GND

GND

L9

GND

VCCAUX

VCCAUX

N9

VCCAUX

GND

GND

L13

GND

VCCAUX

VCCAUX

V5

VCCAUX

GND

GND

M10

GND

VCCAUX

VCCAUX

V18

VCCAUX

GND

GND

M14

GND

VCCAUX

VCCAUX

W11

VCCAUX

GND

GND

M17

GND

VCCINT

VCCINT

J10

VCCINT

GND

GND

M21

GND

VCCINT

VCCINT

K9

VCCINT

GND

GND

N11

GND

VCCINT

VCCINT

K11

VCCINT

GND

GND

N13

GND

VCCINT

VCCINT

K13

VCCINT

GND

GND

P4

GND

VCCINT

VCCINT

L10

VCCINT

GND

GND

P9

GND

VCCINT

VCCINT

L11

VCCINT

GND

GND

P11

GND

VCCINT

VCCINT

L12

VCCINT

GND

GND

P14

GND

VCCINT

VCCINT

L14

VCCINT

GND

GND

P19

GND

VCCINT

VCCINT

M9

VCCINT

GND

GND

T2

GND

VCCINT

VCCINT

M11

VCCINT

GND

GND

T21

GND

VCCINT

VCCINT

M12

VCCINT

GND

GND

U6

GND

VCCINT

VCCINT

M13

VCCINT

GND

GND

U17

GND

VCCINT

VCCINT

N10

VCCINT

GND

GND

V10

GND

VCCINT

VCCINT

N12

VCCINT

GND

GND

V13

GND

VCCINT

VCCINT

N14

VCCINT

GND

GND

Y3

GND

VCCINT

VCCINT

P13

VCCINT

GND

GND

Y20

GND

GND

GND

AA7

GND

GND

GND

AA16

GND

User I/Os by Bank Table 155 indicates how the 304 available user-I/O pins are distributed between the four I/O banks on the FG484 package.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 222

Spartan-3E FPGA Family: Pinout Descriptions

Table 155: User I/Os Per Bank for the XC3S1600E in the FG484 Package Package Edge

I/O Bank

Maximum I/O

Top

0

Right

All Possible I/O Pins by Type VREF(1)

CLK(2)

I/O

INPUT

DUAL

94

56

22

1

7

8

1

94

50

16

21

7

0(2)

Bottom

2

94

45

18

24

7

0(2)

Left

3

94

63

16

0

7

8

376

214

72

46

28

16

TOTAL Notes: 1. 2.

Some VREF and CLK pins are on INPUT pins. The eight global clock pins in this bank have optional functionality during configuration and are counted in the DUAL column.

Footprint Migration Differences The XC3S1600E FPGA is the only Spartan-3E device offered in the FG484 package.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 223

Spartan-3E FPGA Family: Pinout Descriptions

FG484 Footprint

X-Ref Target - Figure 88

Bank 0 1

Left Half of Package (top view)

A

GND

B

PROG_B

2

3

INPUT

INPUT

I/O

I/O

I/O

I/O

I/O

I/O

I/O

L37P_0

L37N_0

L35N_0

L35P_0

L33N_0

L33P_0

L30P_0

L24N_0

L24P_0

VCCO_0

I/O

GND

INPUT

INPUT

INPUT

I/O

I/O

L34P_0

L34N_0

L31N_0

L28N_0

L25P_0

I/O

INPUT

I/O

L36P_0

L31P_0

L29P_0

TDI

4

I/O

I/O

L39P_0

L39N_0

5

6

7

8

9

I/O

I/O

L30N_0

L28P_0

10

C

I/O

I/O

L01N_3

L01P_3

GND

I/O L40P_0

I/O

INPUT: User I/O or

72 reference resistor input for bank

D

DUAL: Configuration pin,

E

46 then possible user I/O

VREF: User I/O or input

F

CLK: User I/O, input, or

G

2

CONFIG: Dedicated configuration pins

H

4

JTAG: Dedicated JTAG port pins

28 voltage reference for bank 16 clock buffer input

K

GND: Ground

VCCO: Output voltage 28 supply for bank

Bank 3

48

J

L

0

I/O L04N_3

I/O L07N_3

I/O L07P_3

I/O L02N_3 VREF_3

VCCO_3

INPUT

GND

I/O L02P_3

I/O

I/O

L03N_3

L03P_3

I/O

I/O

L05P_3

L05N_3

INPUT

I/O

L38N_0 VREF_0

VCCAUX

INPUT

INPUT

GND

I/O

I/O

L06P_3

L06N_3

I/O

I/O

I/O

I/O

L10P_3

L09N_3

L09P_3

VCCO_3

L13N_3 VREF_3

I/O

I/O L16N_3

I/O L16P_3

I/O

INPUT

GND

I/O

N

L20N_3 LHCLK5

GND

I/O L15P_3

VCCAUX

L18N_3 LHCLK1

I/O

I/O

I/O

L21P_3 LHCLK6

L21N_3 LHCLK7

L18P_3 LHCLK0

VCCO_3

INPUT

L24N_3 VREF_3

INPUT

GND

I/O

I/O

I/O L25N_3

INPUT

I/O

INPUT

L25P_3

INPUT

I/O

I/O

I/O

VCCO_3

L12N_3

L15N_3

I/O L08P_3

I/O

I/O

INPUT

I/O

L32N_0 VREF_0

L08N_3 VREF_3

L12P_3

L13P_3

VREF_3

I/O L36N_0

I/O

L10N_3

L11P_3

I/O

L38P_0

I/O

L20P_3 LHCLK4 TRDY2

P

I/O L40N_0 HSWAP

L11N_3

M

VCCINT: Internal core 16 supply voltage (+1.2V) VCCAUX: Auxiliary supply 10 voltage (+2.5V)

I/O L04P_3

GND

INPUT

VCCO_0

I/O L32P_0

I/O

I/O L14P_3

T

U

V

W

Y A A A B

I/O

I/O

I/O

I/O

L28P_3

L28N_3

L29N_3

L29P_3

INPUT

GND

VCCO_3

L19N_3 LHCLK3 IRDY2

I/O

I/O

I/O

I/O

L22N_3

L22P_3

L23P_3

I/O

I/O

I/O

I/O

L27P_3

L27N_3

L26P_3

L23N_3

I/O

I/O

I/O

L32N_3

L32P_3

L30N_3

INPUT

GND

I/O

I/O

I/O

L31N_3

L34P_3

L34N_3

I/O

VCCO_3

I/O

I/O

L33N_3

L36P_3

I/O

I/O

L37P_3

L37N_3

I/O

I/O

L38N_3

L38P_3

GND

INPUT

I/O L26N_3

INPUT

I/O

L33P_3

I/O L30P_3

VREF_3

L31P_3

I/O

I/O

L35P_3

L35N_3

GND I/O L01P_2 CSO_B

I/O L01N_2 INIT_B

INPUT

INPUT L02P_2

INPUT L02N_2

I/O VREF_2

L03P_2 DOUT BUSY

I/O L03N_2 MOSI CSI_B VCCO_2

I/O

INPUT

I/O L22P_0

INPUT

L23N_0

L23P_0

L26P_0

VCCO_0

INPUT I/O

L20N_0 GCLK9

GND

VCCINT

I/O

VCCINT

GND

VCCINT

GND

VCCINT VCCINT

VCCAUX

VCCINT

GND

GND

L13N_2 VREF_2

I/O L17P_2

I/O L17N_2

I/O

I/O

L13P_2

L16P_2

I/O

I/O

VCCINT

I/O

L10P_2

L07P_2

GND

L10N_2

I/O

I/O

VCCINT

I/O INPUT

L07N_2

L04P_2

I/O

I/O L36N_3 VREF_3

VCCAUX

I/O L22N_0

I/O INPUT

L24P_3

VCCO_3

I/O L21P_0 GCLK10

I/O L19P_3 LHCLK2

N.C.: Not connected R

L21N_0 GCLK11

INPUT

INPUT

I/O

I/O

GND

L26N_0

L27P_0

L14N_3

I/O L25N_0 VREF_0

INPUT

I/O

I/O

I/O

I/O

L27N_0

L17P_3

L17N_3

I/O L29N_0

GND I/O

VCCO_0

I/O: Unrestricted,

214 general-purpose user I/O

11

I/O L09N_2 VREF_2

VCCO_2

I/O L12P_2

I/O L16N_2

I/O

I/O

I/O

I/O

INPUT

L06N_2

L09P_2

L12N_2

L15P_2

I/O

I/O

I/O

L05N_2

L06P_2

INPUT L05P_2

GND

I/O L11P_2

I/O L20P_2 D4 GCLK14

I/O L20N_2 D3 GCLK15

I/O L19N_2 D6 GCLK13

I/O GND

L04N_2

INPUT

GND

L19P_2 D7 GCLK12 VCCAUX

INPUT

INPUT

L15N_2

L18P_2

I/O

L18N_2 VREF_2

INPUT VCCO_2

INPUT

INPUT

I/O

I/O

I/O

I/O

L08P_2

L08N_2

L11N_2

L14N_2

L14P_2

D5

Bank 2

DS312_10_101905

Figure 88: FG484 Package Footprint (top view)

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 224

Spartan-3E FPGA Family: Pinout Descriptions

FG484 Footprint

Bank 0 13

14 I/O

INPUT

INPUT

L17N_0

L17P_0

L12N_0 VREF_0

I/O

VCCO_0

I/O L19P_0 GCLK6

I/O L19N_0 GCLK7

VCCAUX

I/O L18P_0 GCLK4

INPUT L14P_0

I/O

L07N_0

L07P_0

L04P_0

L04N_0

L03N_0 VREF_0

I/O

I/O

VCCO_0

INPUT

TDO

L38N_1 LDC2

L38P_1 LDC1

I/O

I/O

GND

L37N_1 LDC0

L37P_1 HDC

L09N_0 VREF_0

I/O

INPUT

I/O

I/O

L06N_0

L05N_0

L01N_0

L01P_0

I/O

INPUT

I/O

INPUT

INPUT

L08P_0

L06P_0

L02N_0

L02P_0

I/O

INPUT

L11P_0

L08N_0

I/O

TCK

VCCAUX

I/O

GND

VCCO_0

I/O L10P_0

I/O

I/O L10N_0

I/O

I/O

L16P_0

L13N_0

I/O L16N_0

GND

GND

I/O

I/O L25P_1

INPUT L21P_2 RDWR_B GCLK0 VCCO_2

I/O L23N_2 DIN D0

VCCINT

I/O

VCCINT INPUT

VCCO_1

GND

I/O L27P_2

INPUT

I/O

L24P_2

L27N_2

I/O L23P_2 M0

I/O L22N_2 D1 GCLK3

I/O L22P_2 D2 GCLK2

I/O M1

GND

GND

L24N_2

I/O

GND

L19P_1 A8 RHCLK2

VCCINT INPUT

INPUT

L26P_2

INPUT

L23P_1

INPUT L21N_2 M2 GCLK1

INPUT

I/O

I/O

GND

INPUT

L25N_1

VCCINT VCCAUX

VCCINT VCCINT

VCCINT

L05P_0

I/O

L13P_0

VCCINT

INPUT

L09P_0

I/O

GND

GND

I/O L26N_2 VREF_2

I/O L29P_2

I/O

I/O L32P_1

I/O L30N_1

I/O

I/O L27P_1

I/O L23N_1 A0

GND

INPUT

VCCAUX

I/O

I/O L10N_1

I/O L10P_1

I/O

I/O L33P_2

VCCO_1

INPUT

I/O L34N_1

VCCO_1

INPUT

GND I/O L28N_1 VREF_1

I/O L26P_1

INPUT

VCCO_1

I/O

L20P_1 A6 RHCLK4 IRDY1

I/O L17P_1

I/O

L34P_2

L36N_2

I/O

I/O

I/O

INPUT

I/O

L25N_2

L28N_2

L32P_2

L34N_2

L36P_2

GND

L35P_2 A23

I/O

L35N_2 A22

GND

INPUT

I/O L31P_1

I/O L28P_1

INPUT

L22N_1 A1

I/O

I/O L22P_1 A2

GND

L18N_1 A9 RHCLK1

INPUT

L18P_1 A10 RHCLK0

VCCO_1

I/O L13N_1

I/O

I/O

I/O

I/O

L09N_1

L11P_1

L11N_1

L13P_1

INPUT

GND

I/O

I/O L06N_1

I/O L04N_1

B

C

D

E

F

G

H

J

I/O L07N_1 VREF_1

I/O

I/O

L04P_1

L03P_1

K

L

M

I/O

I/O

L06P_1

A

I/O

L09P_1

I/O L08N_1

I/O

I/O

L07P_1

L08P_1

VCCO_1

I/O L05N_1

N

P

R

T

U

V

I/O

I/O

I/O

I/O

L38P_2 A21

L40N_2 CCLK

L03N_1 VREF_1

L02N_1 A13

I/O

I/O

GND

L02P_1 A14

L01N_1 A15

Y

I/O DONE

L01P_1 A16

A A

I/O

I/O

L38N_2 A20

L40P_2 VS0 A17

I/O VCCO_2

I/O

Bank 2

I/O L31N_1

L20N_1 A5 RHCLK5

I/O

VCCAUX

INPUT

L17N_1 VREF_1

I/O

INPUT

I/O

I/O L34P_1

I/O

INPUT L37N_2

INPUT L37P_2

Right Half of Package (top view)

I/O

L15P_1

INPUT

L32N_2

DS312 (v4.1) July 19, 2013 Product Specification

INPUT

I/O

I/O

L12N_1 VREF_1

GND

VREF_1

L26N_1

L15N_1

GND

I/O

I/O

L03P_0

I/O

L16P_1 A12

L33N_2

L30N_2

I/O L24N_1

VREF_1

L29N_2

I/O

I/O L24P_1

I/O

I/O

I/O

GND

L21N_1 A3 RHCLK7

I/O

L31P_2

I/O

I/O L29N_1

I/O

L16N_1 A11

INPUT

L30P_2

I/O L29P_1

L21P_1 A4 RHCLK6

INPUT

I/O

I/O

VCCO_1

L27N_1

L12P_1

L28P_2

I/O L32N_1

L33P_1

L25P_2

VCCO_2

I/O L35N_1

I/O

I/O

VCCO_2

I/O L35P_1

L33N_1

L14P_1

INPUT

I/O L36N_1

I/O

I/O

L31N_2 VREF_2

I/O L36P_1

I/O

L19N_1 A7 RHCLK3 TRDY1

INPUT

L30P_1

L14N_1

INPUT

TMS

I/O

22

L12P_0

L11N_0

I/O

21

I/O

L14N_0

L15P_0

20 I/O

I/O

INPUT

GND

19

I/O

L15N_0

GND

18

I/O

I/O

L20P_0 GCLK8

17

I/O

VREF_0

INPUT

16

I/O

I/O L18N_0 GCLK5

15

I/O L39N_2 VS1 A18

I/O L39P_2 VS2 A19

Bank 1

12

I/O VREF_2

I/O L05P_1

GND

W

A B

DS312_11_101905

www.xilinx.com 225

Spartan-3E FPGA Family: Pinout Descriptions

Revision History The following table shows the revision history for this document. Date

Version

03/01/2005

1.0

Initial Xilinx release.

03/21/2005

1.1

Added XC3S250E in the CP132 package to Table 129. Corrected number of differential I/O pairs on CP132. Added pinout and footprint information for the CP132, FG400, and FG484 packages. Removed IRDY and TRDY pins from the VQ100, TQ144, and PQ208 packages.

11/23/2005

2.0

Corrected title of Table 153. Updated differential pair numbering for some pins in Bank 0 of the FG400 package, affecting Table 152 and Figure 87. Pin functionality and ball assignment were not affected. Added Package Thermal Characteristics section. Added package mass values to Table 125.

03/22/2006

3.0

Included I/O pins, not just input-only pins under the VREF description in Table 124. Clarified that some global clock inputs are Input-only pins in Table 124. Added information on the XC3S100E in the CP132 package, affecting Table 129, Table 130, Table 133, Table 134, Table 136, and Figure 81. Ball A12 on the XC3S1600E in the FG320 package a full I/O pin, not an Input-only pin. Corrected the I/O counts for the XC3S1600E in the FG320 package, affecting Table 129, Table 150, Table 151, and Figure 86. Corrected pin type for XC3S1600E balls N14 and N15 in Table 148.

05/19/2006

3.1

Minor text edits.

11/09/2006

3.4

Added package thermal data for the XC3S100E in the CP132 package to Table 130. Corrected pin migration arrows for balls E17 and F4 between the XC3S500E and XC3S1600E in Table 151. Promoted Module 4 to Production status. Synchronized all modules to v3.4.

03/16/2007

3.5

Minor formatting changes.

05/29/2007

3.6

Corrected ‘Lxx’ to ‘Lxxy’ in Table 124. Noted that some GCLK and VREF pins are on INPUT pins in Table 124 and Table 129. Added link before Table 127 to Material Declaration Data Sheets.

04/18/2008

3.7

Added XC3S500E VQG100 package. Added Material Declaration Data Sheet links in Table 127. Updated Thermal Characteristics in Table 130. Updated links.

08/26/2009

3.8

Minor typographical updates.

10/29/2012

4.0

Added Notice of Disclaimer. This product is not recommended for new designs. Updated the XC3S250E-FT256 in Table 129.

07/19/2013

4.1

Removed banner. This product IS recommended for new designs.

DS312 (v4.1) July 19, 2013 Product Specification

Revision

www.xilinx.com 226

Spartan-3E FPGA Family: Pinout Descriptions

Notice of Disclaimer THE XILINX HARDWARE FPGA AND CPLD DEVICES REFERRED TO HEREIN (“PRODUCTS”) ARE SUBJECT TO THE TERMS AND CONDITIONS OF THE XILINX LIMITED WARRANTY WHICH CAN BE VIEWED AT http://www.xilinx.com/warranty.htm. THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY USE OF PRODUCTS IN AN APPLICATION OR ENVIRONMENT THAT IS NOT WITHIN THE SPECIFICATIONS STATED IN THE XILINX DATA SHEET. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, OR ANY OTHER APPLICATION THAT INVOKES THE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). USE OF PRODUCTS IN CRITICAL APPLICATIONS IS AT THE SOLE RISK OF CUSTOMER, SUBJECT TO APPLICABLE LAWS AND REGULATIONS. CRITICAL APPLICATIONS DISCLAIMER XILINX PRODUCTS (INCLUDING HARDWARE, SOFTWARE AND/OR IP CORES) ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS IN LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, CLASS III MEDICAL DEVICES, NUCLEAR FACILITIES, APPLICATIONS RELATED TO THE DEPLOYMENT OF AIRBAGS, OR ANY OTHER APPLICATIONS THAT COULD LEAD TO DEATH, PERSONAL INJURY OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (INDIVIDUALLY AND COLLECTIVELY, “CRITICAL APPLICATIONS”). FURTHERMORE, XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN ANY APPLICATIONS THAT AFFECT CONTROL OF A VEHICLE OR AIRCRAFT, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE OPERATOR. CUSTOMER AGREES, PRIOR TO USING OR DISTRIBUTING ANY SYSTEMS THAT INCORPORATE XILINX PRODUCTS, TO THOROUGHLY TEST THE SAME FOR SAFETY PURPOSES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN CRITICAL APPLICATIONS. AUTOMOTIVE APPLICATIONS DISCLAIMER XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS APPLICATIONS RELATED TO: (I) THE DEPLOYMENT OF AIRBAGS, (II) CONTROL OF A VEHICLE, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE OPERATOR, OR (III) USES THAT COULD LEAD TO DEATH OR PERSONAL INJURY. CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN SUCH APPLICATIONS.

DS312 (v4.1) July 19, 2013 Product Specification

www.xilinx.com 227

Loading...

Xilinx DS312 Spartan-3E FPGA Family Data Sheet, Data Sheet

1 Spartan-3E FPGA Family Data Sheet DS312 July 19, 2013 Product Specification Module 1: Introduction and Ordering Information Module 3: DC and Sw...

6MB Sizes 3 Downloads 0 Views

Recommend Documents

Xilinx DS312 Spartan-3E FPGA Family Data Sheet, Data Sheet
Aug 26, 2009 - Spartan-3E FPGAs support the following single-ended standards: ...... Figure 57, page 84 demonstrates how

PIC24FJ256GB210 Family Data Sheet - Geeetech
Code protection does not ...... If you have any questions or comments regarding this publication, please contact the Mar

Data sheet
start of lifetime: 66 W, end of lifetime: 66 W, reduction: 33 W, luminaire housing, of diecast aluminium, powder-coated,

Data sheet
Jan 24, 2013 - Acceptance standard. None; tolerances to ISO 9906. Class 2A / 3B; below 10 kW acc. to paragraph 4.4.2. Wa

DATA SHEET
April 2017. ITEM. PART NUMBERS. DESCRIPTION. QTY. 5CP6120. 5CP6120CSSG1. MATL. 283. 34334. —. Kit, Oil Drain (3/8” x

DATA SHEET
Application. The kWh meters types WQR96 MKII and WQ2R96 MKII are intended for energy measurement in single-phase and 3-

PIC16F84A Data Sheet - Microchip
High Performance RISC CPU Features: • Only 35 single word instructions to learn. • All instructions single-cycle exc

Major Works Data Sheet
Albert Camus was born in French colonial. Algiers. His father was killed in WWI, and he, his brother, mother, grandmothe

safety data sheet - Betco
Precautionary statements. Prevention. : Wear protective gloves: < 1 hour (breakthrough time): disposable vinyl. Wear eye

data sheet - Digital Fire
DESCRIPTION. HFC-227ea provides superior fire protection in a wide range of applications from sensitive electrical equip

Interpersonal Communications - 2119 Words | Knightfall | El ministerio del tiempo (7)